Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Strength of Materials: Simple Stresses, Strains & Strain Energy

Civil Engineering · Strength of Materials

25 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Stress at a section of a loaded member is defined as

  1. change in length per unit original length of the member
  2. internal resisting force per unit cross-sectional area
  3. applied load per unit volume of the member
  4. internal resisting force per unit length of the member
Show answer & solution

Answer: (B) internal resisting force per unit cross-sectional area

σ = P/A, the internal resisting force divided by the cross-sectional area; its SI unit is N/m² (Pa).

Question 2

Normal (linear) strain in a loaded bar is defined as the

  1. applied force divided by the change in length
  2. original length divided by the change in length
  3. change in length divided by the original length
  4. change in length divided by the cross-sectional area
Show answer & solution

Answer: (C) change in length divided by the original length

ε = δL/L is a ratio of two lengths, so it is dimensionless.

Question 3

Hooke's law states that stress is proportional to strain within the

  1. strain-hardening range after yielding has started
  2. linear elastic range of the material
  3. fracture region just before the specimen breaks
  4. necking region beyond the ultimate stress
Show answer & solution

Answer: (B) linear elastic range of the material

Stress and strain are linearly related (σ = Eε) only up to the proportional limit, inside the elastic range.

Question 4

The SI unit of stress is the

  1. kilogram per square metre (kg/m²)
  2. newton per metre (N/m)
  3. pascal (N/m²)
  4. newton-metre (N·m)
Show answer & solution

Answer: (C) pascal (N/m²)

Stress = force/area = N/m², which is called the pascal (Pa).

Question 5

A material is called plastic when

  1. it keeps some permanent deformation after the load is removed
  2. it recovers its original shape completely once the load is removed
  3. it fractures with no measurable deformation under the load
  4. its strain stays proportional to stress right up to fracture
Show answer & solution

Answer: (A) it keeps some permanent deformation after the load is removed

Plastic behaviour is non-recoverable deformation; a perfectly elastic material returns fully to its original shape on unloading.

Question 6

The stress at which a ductile material begins to deform plastically, with a marked increase in strain, is called the

  1. permissible working stress
  2. ultimate tensile stress
  3. endurance stress under cyclic loading
  4. yield stress
Show answer & solution

Answer: (D) yield stress

Yield stress marks the transition from elastic to plastic behaviour.

Question 7

The maximum nominal stress reached on the stress-strain curve of a tensile test is called the

  1. permissible working stress adopted in design
  2. lower yield stress at the end of the yield plateau
  3. ultimate tensile stress
  4. 0.2% offset proof stress of the material
Show answer & solution

Answer: (C) ultimate tensile stress

Ultimate tensile stress is the peak of the engineering stress-strain curve (maximum load divided by original area).

Question 8

Factor of safety is defined as

  1. working load divided by the cross-sectional area of the member
  2. ultimate strain divided by the working strain at the yield point
  3. permissible working stress divided by the yield or ultimate stress
  4. yield or ultimate stress divided by the permissible working stress
Show answer & solution

Answer: (D) yield or ultimate stress divided by the permissible working stress

FoS = failure stress / permissible stress, so it is greater than 1.

Question 9

Permissible (working) stress is obtained by

  1. dividing the modulus of elasticity by the factor of safety
  2. adding the factor of safety to the yield stress of the material
  3. dividing the yield or ultimate stress by the factor of safety
  4. multiplying the yield or ultimate stress by the factor of safety
Show answer & solution

Answer: (C) dividing the yield or ultimate stress by the factor of safety

σ_perm = σ_failure / FoS, which keeps the working stress well below the failure stress.

Question 10

A bar of length L and cross-sectional area A, with modulus of elasticity E, carries an axial load P within the elastic limit. Its elongation is

  1. PL/(AE)
  2. PE/(AL)
  3. PA/(LE)
  4. AE/(PL)
Show answer & solution

Answer: (A) PL/(AE)

σ = P/A and ε = σ/E, so δ = εL = PL/(AE).

Question 11

Two bars of equal length but different materials are fixed side by side between two rigid end plates and carry a common axial load. Compatibility requires that they have

  1. the same elongation, so their stresses generally differ
  2. the same share of the load, whatever their stiffnesses
  3. the same stress, so their elongations generally differ
  4. the same modulus of elasticity, so only their strains differ
Show answer & solution

Answer: (A) the same elongation, so their stresses generally differ

Rigid connection forces equal elongation, hence equal strain; stresses then divide in proportion to the moduli (σ = Eε).

Question 12

On the stress-strain curve of mild steel, the point up to which stress remains proportional to strain is called the

  1. proportional limit
  2. upper yield point
  3. ultimate point
  4. breaking (fracture) point
Show answer & solution

Answer: (A) proportional limit

Beyond the proportional limit the curve is no longer a straight line.

Question 13

The greatest stress that can be applied to a material without leaving any permanent set after unloading is called the

  1. breaking point
  2. necking point
  3. ultimate point
  4. elastic limit
Show answer & solution

Answer: (D) elastic limit

Below the elastic limit all deformation is recovered on unloading; above it some permanent deformation remains.

Question 14

In the stress-strain diagram of mild steel, the region after the yield plateau in which stress rises again with strain up to the ultimate stress is called the

  1. linear elastic region
  2. necking region beyond the ultimate stress
  3. upper yield point region
  4. strain-hardening region
Show answer & solution

Answer: (D) strain-hardening region

After yielding, the material regains some load-carrying capacity as it strain-hardens, until the ultimate stress is reached.

Question 15

Necking in a ductile tensile test specimen refers to

  1. an increase of cross-sectional area under tensile load
  2. a uniform lengthening along the whole gauge length before yielding
  3. a crack starting at the grips because of the clamping force
  4. a localised reduction of cross-sectional area just before fracture
Show answer & solution

Answer: (D) a localised reduction of cross-sectional area just before fracture

After the ultimate stress is reached, deformation concentrates in one region and the area there shrinks until fracture.

Question 16

Proof stress (for example the 0.2% offset stress) is used for materials that

  1. lack a clearly defined yield point, such as aluminium alloys
  2. fracture elastically with no plastic strain, such as glass
  3. show a long and sharp yield plateau, as annealed mild steel does
  4. are loaded only in compression, such as plain concrete
Show answer & solution

Answer: (A) lack a clearly defined yield point, such as aluminium alloys

Where there is no distinct yield point, the stress giving 0.2% permanent strain is used as a practical yield stress.

Question 17

Thermal stress develops in a bar when

  1. its free expansion or contraction under a temperature change is prevented
  2. it is heated uniformly while its two ends are free
  3. its temperature is held constant while an axial load acts
  4. it is free to expand or contract as its temperature changes along the length
Show answer & solution

Answer: (A) its free expansion or contraction under a temperature change is prevented

A temperature change alone produces strain without stress; stress arises only if that strain is restrained.

Question 18

A steel bar is fully restrained at its two ends and heated by ΔT. With coefficient of thermal expansion α and modulus E, the stress developed is

  1. σ = αΔT/E (compressive)
  2. σ = E/(αΔT) (tensile)
  3. σ = EαΔT (compressive)
  4. σ = Eα/ΔT (compressive)
Show answer & solution

Answer: (C) σ = EαΔT (compressive)

The prevented free strain is αΔT, so σ = Eε = EαΔT; on heating the stress is compressive.

Question 19

Two bars of different materials are rigidly joined side by side and heated uniformly. The material with the larger coefficient of thermal expansion develops

  1. tensile stress, while the other material develops compressive stress
  2. compressive stress, while the other material develops tensile stress
  3. tensile stress, and so does the other material
  4. no stress, because the two bars are at the same temperature
Show answer & solution

Answer: (B) compressive stress, while the other material develops tensile stress

The bar that tends to expand more is held back by its partner (compression); the partner is stretched (tension), and the two axial forces balance.

Question 20

The strain energy stored in a bar of volume V under a gradually applied axial stress σ (modulus E) is

  1. σV/(2E)
  2. σ²V/(2E)
  3. σ²V/E
  4. σ²V/(4E)
Show answer & solution

Answer: (B) σ²V/(2E)

U = ½ × σ × ε × V = σ²V/(2E).

Question 21

The proof resilience of a material is the

  1. total strain energy per unit volume absorbed until the specimen finally fractures
  2. energy dissipated as heat per unit volume during each complete load cycle
  3. strain energy stored per unit volume when the ultimate stress is just reached
  4. maximum strain energy stored without permanent deformation (up to the elastic limit)
Show answer & solution

Answer: (D) maximum strain energy stored without permanent deformation (up to the elastic limit)

Proof resilience is the strain energy stored when the material is stressed exactly to its elastic limit; resilience in general is recoverable energy.

Question 22

The modulus of resilience of a material is

  1. the proof resilience per unit volume
  2. the total energy absorbed per unit volume up to fracture
  3. the proof resilience multiplied by the volume of the member
  4. the strain energy per unit length stored up to fracture
Show answer & solution

Answer: (A) the proof resilience per unit volume

Modulus of resilience = σ_el²/(2E); dividing by volume lets materials be compared independently of size.

Question 23

A load is applied suddenly (with no initial velocity) to a bar. The maximum stress produced is

  1. equal to the stress due to the same load applied gradually
  2. twice the stress due to the same load applied gradually
  3. four times the stress due to the same load applied gradually
  4. half the stress due to the same load applied gradually
Show answer & solution

Answer: (B) twice the stress due to the same load applied gradually

Work done by P through the extension equals the strain energy: Pδ = σ²V/(2E) with δ = σL/E, giving σ = 2P/A.

Question 24

Compared with the same weight applied gradually, an impact load (weight falling from a height) produces a peak stress that is

  1. smaller, since the load acts on the bar for only a very short interval of time
  2. equal, since the weight and the area are unchanged
  3. larger, since kinetic energy must also be absorbed as strain energy
  4. lower, because the material hardens under rapid loading
Show answer & solution

Answer: (C) larger, since kinetic energy must also be absorbed as strain energy

The falling weight's energy adds to the energy to be stored, so σ_impact exceeds σ_static; the gradual load gives the lowest stress.

Question 25

A steel bar 1 m long with a cross-sectional area of 100 mm² and E = 200 GPa carries an axial tensile load of 20 kN. Its elongation is

  1. 0.5 mm
  2. 1.0 mm
  3. 2.0 mm
  4. 4.0 mm
Show answer & solution

Answer: (B) 1.0 mm

δ = PL/(AE) = (20 000 × 1000)/(100 × 200 000) = 1.0 mm.

Practice these 25 questions interactively →