Young's modulus E is the ratio of
Show answer & solution
Answer: (A) direct (axial) stress to the corresponding axial strain within the elastic limit
E = σ/ε relates direct stress to direct strain in the elastic range.
Civil Engineering · Strength of Materials
26 questions, each with the answer and a worked solution.
Practice interactively and track your score →Young's modulus E is the ratio of
Answer: (A) direct (axial) stress to the corresponding axial strain within the elastic limit
E = σ/ε relates direct stress to direct strain in the elastic range.
The modulus of rigidity G is the ratio of
Answer: (A) shear stress to shear strain within the elastic limit
G = τ/γ, the shear modulus.
The bulk modulus K, which governs the response to uniform pressure on all faces, is the ratio of
Answer: (B) hydrostatic (volumetric) stress to volumetric strain
K = p/ε_v; it measures resistance to uniform volumetric compression.
For axial loading, Poisson's ratio ν is defined as
Answer: (A) the lateral strain divided by the longitudinal strain, taken in magnitude
ν = |ε_lateral| / ε_longitudinal.
The relationship between Young's modulus E, modulus of rigidity G and Poisson's ratio ν is
Answer: (A) E = 2G(1 + ν)
Standard relation: G = E/[2(1 + ν)], so E = 2G(1 + ν). For E = 200 GPa and ν = 0.25, G = 80 GPa.
The relationship between Young's modulus E, bulk modulus K and Poisson's ratio ν is
Answer: (B) E = 3K(1 − 2ν)
Standard relation: K = E/[3(1 − 2ν)], so E = 3K(1 − 2ν). K is positive only if ν < 0.5.
Eliminating Poisson's ratio from E = 2G(1 + ν) and E = 3K(1 − 2ν) gives E in terms of K and G as
Answer: (C) E = 9KG/(3K + G)
Eliminating ν between the two relations gives E = 9KG/(3K + G); a check with ν = 0.3 returns E exactly.
For most engineering metals such as steel and aluminium, Poisson's ratio typically lies between
Answer: (B) 0.25 and 0.35
Common metals have ν of about 0.25 to 0.35; for any isotropic material ν lies between −1 and 0.5.
When a bar is stretched axially, the lateral strain is
Answer: (D) the fractional change in a transverse dimension, of opposite sign to axial strain
A bar that lengthens under tension contracts transversely; lateral strain = −νε.
Volumetric strain is defined as
Answer: (D) the change in volume divided by the original volume
ε_v = δV/V; for small strains it equals the sum of the three normal strains.
Poisson's ratio has the units of
Answer: (C) none (dimensionless ratio)
It is a ratio of two strains, each of which is dimensionless.
Percentage elongation at fracture in a tensile test is mainly a measure of a material's
Answer: (A) ductility
The greater the permanent elongation before fracture, the more ductile the material.
A brittle material typically
Answer: (B) fractures with little or no plastic deformation
Brittle materials break suddenly at small strain, with no significant yielding.
Which of the following is a typical brittle material?
Answer: (A) cast iron
Cast iron fractures with very little plastic strain, whereas the other metals listed are ductile.
Toughness of a material is its capacity to
Answer: (C) absorb energy up to fracture, including plastic deformation
Toughness is the total area under the stress-strain curve up to fracture.
Creep is
Answer: (C) slow time-dependent deformation under sustained stress, mostly at high temperature
Under constant stress, strain keeps increasing with time; the effect is pronounced at high temperature.
Fatigue failure occurs mainly when a member is subjected to
Answer: (A) repeated or cyclic stresses, often below the ultimate strength
Cracks initiate and grow under fluctuating stress, so failure can occur well below the static strength.
Hardness of a material is its resistance to
Answer: (B) indentation, scratching or abrasion of the surface
Brinell, Rockwell and Vickers tests all measure resistance to local surface indentation.
Malleability is the ability of a material to be
Answer: (D) hammered or rolled into thin sheets without fracture
Malleability is plastic deformation under compressive forming such as rolling or hammering.
Ductility is the ability of a material to be
Answer: (D) drawn into wire, with large tensile plastic strain, without fracture
Ductility is large permanent elongation under tension; wire drawing is the classic example.
The endurance (fatigue) limit of a material is the
Answer: (D) stress amplitude below which it withstands a very large number of cycles without failure
Below the endurance limit, fatigue failure does not occur for practical purposes (for steels, at about 10⁶ to 10⁷ cycles).
An S-N curve is mainly used to study
Answer: (B) fatigue life, as stress amplitude plotted against cycles to failure
S-N curves plot stress amplitude (S) against number of cycles to failure (N).
Stress concentration at a hole, notch or fillet means
Answer: (D) a local rise in stress at the discontinuity, well above nominal stress
Geometric discontinuities disturb the stress flow; peak stress = K_t × nominal stress, with K_t > 1.
Stress concentration factors are especially important in design against
Answer: (C) fatigue loading, where they markedly reduce the endurance strength
Local stress peaks start fatigue cracks; in static loading of ductile material, local yielding relieves them.
Rounding (filleting) a sharp internal corner in a machine part mainly
Answer: (C) reduces the local stress concentration at the corner
A generous fillet radius lets the stress flow smoothly round the change of section, lowering K_t.
The endurance ratio of a material is the ratio of its
Answer: (D) endurance limit to its ultimate tensile strength
Endurance ratio = σ_e/σ_u, commonly about 0.4 to 0.5 for steels.