Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Strength of Materials: Columns, Pressure Vessels & Joints

Civil Engineering · Strength of Materials

40 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

A column is a structural member that mainly carries

  1. a twisting moment about its axis
  2. axial tensile load
  3. a transverse load causing bending
  4. axial compressive load
Show answer & solution

Answer: (D) axial compressive load

Columns are compression members and may fail by buckling.

Question 2

The slenderness ratio of a column is defined as

  1. the length divided by the cross-sectional area
  2. the radius of gyration divided by the effective length
  3. the effective length divided by the least lateral dimension
  4. effective length divided by least radius of gyration
Show answer & solution

Answer: (D) effective length divided by least radius of gyration

λ = Le/r_min; buckling behaviour is governed by it.

Question 3

A column with a high slenderness ratio fails mainly by

  1. tensile rupture of the material at the extreme fibre
  2. buckling, at a stress well below the crushing strength
  3. shear along planes at 45° to the axis
  4. crushing of the material at a stress equal to its crushing strength
Show answer & solution

Answer: (B) buckling, at a stress well below the crushing strength

Short columns crush, but slender columns become unstable at a load that stresses the material below its crushing strength.

Question 4

Euler's formula for the buckling load is applicable to

  1. short, stocky columns that fail by crushing
  2. beams carrying combined bending and torsion
  3. long, slender columns that buckle elastically
  4. columns of every slenderness, provided the load is axial
Show answer & solution

Answer: (C) long, slender columns that buckle elastically

Euler assumes elastic buckling, which is valid only when the slenderness ratio is large enough.

Question 5

Euler's crippling load for a column of effective length Le, least second moment of area I and modulus E is

  1. Pcr = π²EI/Le²
  2. Pcr = π²EI/Le
  3. Pcr = πEI/Le
  4. Pcr = π²EA/Le²
Show answer & solution

Answer: (A) Pcr = π²EI/Le²

Solving EI y'' + Py = 0 with hinged ends gives Pcr = π²EI/L²; Le replaces L for other end conditions.

Question 6

The effective length of a column of length L with fixed ends is

  1. 0.5L
  2. 0.7L
  3. 1.0L
  4. 2.0L
Show answer & solution

Answer: (A) 0.5L

Full end fixity gives the smallest effective length, Le = L/2.

Question 7

The effective length of a column of length L with one end fixed and the other free is

  1. 0.5L
  2. 0.7L
  3. 1.0L
  4. 2.0L
Show answer & solution

Answer: (D) 2.0L

The fixed-free column buckles like half of a pinned column of length 2L, so Le = 2L.

Question 8

The effective length of a column of length L with hinged ends is

  1. 0.5L
  2. 0.7L
  3. 1.0L
  4. 2.0L
Show answer & solution

Answer: (C) 1.0L

The pinned-pinned case is the Euler baseline: Le = L.

Question 9

The effective length of a column of length L with one end fixed and the other hinged is

  1. 0.5L
  2. 0.7L
  3. 1.0L
  4. 2.0L
Show answer & solution

Answer: (B) 0.7L

The fixed-hinged column has an intermediate effective length of about 0.7L.

Question 10

Rankine's formula for columns is often preferred to Euler's formula because it

  1. applies only to columns with fixed ends
  2. applies only to very long columns where Euler's formula fails
  3. is empirical and covers short as well as long columns
  4. ignores the effect of the slenderness ratio
Show answer & solution

Answer: (C) is empirical and covers short as well as long columns

Rankine-Gordon interpolates between crushing (short columns) and Euler buckling (long columns).

Question 11

According to Euler's theory, the buckling load of a column is inversely proportional to the

  1. square of its effective length
  2. square root of its effective length
  3. effective length itself (first power)
  4. cube of its effective length
Show answer & solution

Answer: (A) square of its effective length

Pcr = π²EI/Le², so doubling the effective length cuts Pcr to one quarter.

Question 12

A strut differs from a column in that a strut

  1. is short and stocky, whereas a column is slender
  2. carries tension only, whereas a column carries compression only
  3. carries bending only, whereas a column carries axial load
  4. may be inclined or horizontal, a column being typically vertical
Show answer & solution

Answer: (D) may be inclined or horizontal, a column being typically vertical

The two are compression members; the distinction is mainly one of orientation.

Question 13

Buckling of a long column is considered more dangerous than crushing of a short column because it

  1. occurs at a higher stress than crushing, so the member is overloaded
  2. occurs below the crushing stress, often suddenly with little warning
  3. occurs only when the load acts transversely to the axis
  4. can be detected early because deflections grow slowly before failure
Show answer & solution

Answer: (B) occurs below the crushing stress, often suddenly with little warning

Buckling is an instability; the member can collapse suddenly while its material stress is still modest.

Question 14

The Euler buckling load of a column of length l with fixed ends (effective length l/2) is

  1. 2π²EI/l²
  2. 4π²EI/l²
  3. π²EI/l²
  4. π²EI/(4l²)
Show answer & solution

Answer: (B) 4π²EI/l²

Pcr = π²EI/Le² with Le = l/2 gives 4π²EI/l², four times the pinned-pinned value.

Question 15

A cylindrical shell is treated as thin when the ratio of wall thickness to diameter is less than about

  1. 1/2
  2. 1/5
  3. 1/20
  4. 1/500
Show answer & solution

Answer: (C) 1/20

Thin-shell theory assumes uniform stress across the wall, which is acceptable when t/d is less than about 1/20 (some texts use 1/10).

Question 16

A thin cylindrical shell of internal diameter d and thickness t carries internal pressure p. The hoop stress is

  1. 2pd/t
  2. pd/(4t)
  3. pd/(2t)
  4. pd/t
Show answer & solution

Answer: (C) pd/(2t)

Resolving forces on a half-ring: σ_h × 2t = p × d, so σ_h = pd/(2t).

Question 17

A thin cylindrical shell of internal diameter d and thickness t carries internal pressure p. The longitudinal stress is

  1. pd/(4t)
  2. pd/t
  3. pd/(2t)
  4. pd/(8t)
Show answer & solution

Answer: (A) pd/(4t)

Axial force pπd²/4 acts on the ring area πdt, so σ_l = pd/(4t).

Question 18

In a thin cylindrical shell under internal pressure, the ratio of hoop stress to longitudinal stress is

  1. 1 : 1
  2. 1 : 2
  3. 2 : 1
  4. 4 : 1
Show answer & solution

Answer: (C) 2 : 1

σ_h/σ_l = [pd/(2t)]/[pd/(4t)] = 2.

Question 19

The wall thickness of a thin cylindrical shell is normally designed on the basis of

  1. the shear stress at the inner surface
  2. the longitudinal stress, because it acts along the axis
  3. hoop stress, because it is the larger principal stress
  4. the radial stress, because it is the largest of the three
Show answer & solution

Answer: (C) hoop stress, because it is the larger principal stress

The hoop stress is twice the longitudinal stress, so it governs the required thickness.

Question 20

A thin spherical shell of internal diameter d and thickness t carries internal pressure p. The wall stress is

  1. pd/(2t) circumferentially and pd/(4t) along the axis
  2. pd/(4t), equal in every direction in the plane of the wall
  3. pd/(2t), equal in every direction in the plane of the wall
  4. pd/(4t) circumferentially and pd/(2t) meridionally
Show answer & solution

Answer: (B) pd/(4t), equal in every direction in the plane of the wall

Cutting the sphere in half: σ × πdt = p × πd²/4, so σ = pd/(4t).

Question 21

A thin sphere and a thin cylinder have the same diameter, thickness and internal pressure. The wall stress in the sphere compared with the hoop stress in the cylinder is

  1. one quarter
  2. one half
  3. equal
  4. double
Show answer & solution

Answer: (B) one half

Sphere: pd/(4t); cylinder hoop: pd/(2t). The sphere's stress is half as large.

Question 22

Thick cylinders, whose wall is not thin compared with the diameter, are analysed using

  1. Lamé's equations, which allow for stress variation across the wall
  2. the torsion formula for hollow circular shafts
  3. simple bending theory applied to the wall as a beam
  4. the thin-cylinder formulas, assuming uniform stress across the wall
Show answer & solution

Answer: (A) Lamé's equations, which allow for stress variation across the wall

Lamé's theory gives hoop and radial stresses that vary with radius.

Question 23

In a thick cylinder under internal pressure only, the Lamé hoop stress is

  1. zero at the inner surface and greatest at the outer surface
  2. greatest at the outer surface and decreasing towards the inner surface
  3. uniform across the wall thickness
  4. greatest at the inner surface and decreasing towards the outer surface
Show answer & solution

Answer: (D) greatest at the inner surface and decreasing towards the outer surface

σ_h = a + b/r² decreases with radius, so the bore is the critical location.

Question 24

In a thick cylinder with no external pressure, the radial stress at the outer surface is

  1. equal to the longitudinal stress
  2. equal to the internal pressure
  3. equal to the hoop stress at the outer surface
  4. zero, since there is no external pressure
Show answer & solution

Answer: (D) zero, since there is no external pressure

The boundary condition at the free outer surface is σ_r = 0; at the bore σ_r = −p.

Question 25

Autofrettage of a thick cylinder is used to

  1. induce residual compressive stress at the bore, raising pressure capacity
  2. reduce the longitudinal stress to zero
  3. remove the residual stresses left by casting
  4. induce residual tensile stress at the bore so that the yield stress rises
Show answer & solution

Answer: (A) induce residual compressive stress at the bore, raising pressure capacity

Overpressurising so the bore yields leaves it in compression on unloading, offsetting later tensile hoop stress.

Question 26

Wire winding on a thick cylinder is done mainly to

  1. increase the longitudinal stress so that it balances the hoop stress
  2. put the wall in initial compression to resist higher internal pressure
  3. put the wall in initial tension so as to equalise the hoop stress and radial stress
  4. raise the temperature of the wall so that the metal is annealed
Show answer & solution

Answer: (B) put the wall in initial compression to resist higher internal pressure

Pre-tensioned wire compresses the wall, so a larger internal pressure is needed before tensile hoop stress develops.

Question 27

For a thin cylindrical shell under internal pressure, the volumetric strain in terms of the hoop strain ε_h and longitudinal strain ε_l is

  1. ε_v = ε_h + 2ε_l
  2. ε_v = 2ε_h + ε_l
  3. ε_v = ε_h + ε_l
  4. ε_v = 2(ε_h + ε_l)
Show answer & solution

Answer: (B) ε_v = 2ε_h + ε_l

V = (π/4)d²L, so δV/V = 2(δd/d) + δL/L = 2ε_h + ε_l.

Question 28

For a thin cylindrical shell under internal pressure, the hoop strain is

  1. equal to the longitudinal strain, because the stresses act in the same plane
  2. smaller than the longitudinal strain, because of the Poisson effect
  3. unaffected by Poisson's ratio, since the hoop direction is unconstrained
  4. larger than the longitudinal strain, since hoop stress is the larger one
Show answer & solution

Answer: (D) larger than the longitudinal strain, since hoop stress is the larger one

ε_h = (pd/4tE)(2 − ν) exceeds ε_l = (pd/4tE)(1 − 2ν) for any ν.

Question 29

Rivet holes in the shell plates of a pressure vessel reduce the strength of the shell mainly because they

  1. add tensile load to the plate through the rivet shanks
  2. increase the wall thickness locally and raise the pressure
  3. raise the ductility of the plate near the hole
  4. remove material from the section and concentrate stress
Show answer & solution

Answer: (D) remove material from the section and concentrate stress

The weakened section and the stress concentrations lower the efficiency of the joint compared with solid plate.

Question 30

In pressure vessels, hemispherical ends are preferred to flat ends because

  1. they develop large bending stresses at the junction with the shell
  2. they are heavier and weaker than flat ends of the same thickness
  3. they remove the need for any stress analysis of the end
  4. the stress is lower and more uniform, so the end can be thinner
Show answer & solution

Answer: (D) the stress is lower and more uniform, so the end can be thinner

A hemisphere carries pressure by membrane stress pd/(4t), whereas a flat end must resist the pressure by bending.

Question 31

In a riveted lap joint, the plates

  1. are placed edge to edge and connected through cover plates on one or two sides
  2. overlap, and are joined by rivets passing through the overlap
  3. are placed at right angles and connected through an angle section
  4. overlap by a full width and are connected only by welds
Show answer & solution

Answer: (B) overlap, and are joined by rivets passing through the overlap

A lap joint has the plate edges overlapped and riveted through the overlapped region.

Question 32

In a riveted butt joint, the plates

  1. are placed at right angles and joined through an angle section
  2. overlap and are joined by a single row of rivets through the overlap
  3. overlap and are joined by caulked seams without rivets
  4. lie edge to edge and are riveted through one or two cover plates
Show answer & solution

Answer: (D) lie edge to edge and are riveted through one or two cover plates

The plates stay in the same plane and the load passes through the cover plates.

Question 33

The efficiency of a riveted joint is the ratio of

  1. the strength of the solid plate to the strength of the joint
  2. the strength of the joint to the strength of the solid plate
  3. the number of rivets to the thickness of the plate
  4. the diameter of the rivet to the pitch of the rivets
Show answer & solution

Answer: (B) the strength of the joint to the strength of the solid plate

η = (least strength of the joint per pitch) / (strength of solid plate per pitch), always less than 1.

Question 34

Which set lists the principal modes of failure of a riveted lap joint?

  1. plate tearing between rivet holes, rivet shearing, and crushing (bearing) of plate or rivet
  2. yielding of the rivet heads, twisting of the plate, and corrosion of the rivet shanks
  3. buckling of the rivets, thermal cracking of the plate, and fatigue of the rivet heads
  4. bending of the plate between rivets, torsion of the rivet shanks, and creep of the rivet heads
Show answer & solution

Answer: (A) plate tearing between rivet holes, rivet shearing, and crushing (bearing) of plate or rivet

A joint is designed against plate tearing, rivet shear and bearing; its strength is the least of these.

Question 35

Compared with a riveted joint of similar strength, a welded joint is generally

  1. lighter, since it needs no overlap, cover plates or weakening rivet holes
  2. weaker, because welding reduces the cross-section of the plate
  3. heavier, because the weld metal weighs more than rivet heads and cover plates
  4. unable to resist fatigue loading, unlike a riveted joint
Show answer & solution

Answer: (A) lighter, since it needs no overlap, cover plates or weakening rivet holes

Welding avoids section loss at holes and extra cover plates, so efficiency and weight are better.

Question 36

A fillet weld is typically used to join

  1. coplanar plates joined edge to edge with full penetration
  2. round bars butted end to end for full-strength joints
  3. plates that overlap or meet at an angle (lap and T-joints)
  4. plates that have first been bolted together
Show answer & solution

Answer: (C) plates that overlap or meet at an angle (lap and T-joints)

Fillet welds are laid in the corner of lap and T-joints and need no edge preparation.

Question 37

A butt weld typically joins plates that are

  1. joined through a plug of weld metal in a hole
  2. overlapping, with the weld along their edges
  3. in the same plane, edge to edge, often with bevelled edges
  4. at right angles to each other, as in a T-joint or corner joint
Show answer & solution

Answer: (C) in the same plane, edge to edge, often with bevelled edges

Butt welds join coplanar plate edges and often need bevelled edges for full penetration.

Question 38

Caulking of a riveted joint in a boiler or pressure vessel is done mainly to

  1. make the joint leak-proof against fluid pressure
  2. reduce the shear stress in the shanks of the rivets
  3. increase the pitch of the rivets
  4. increase the tensile strength of the plate
Show answer & solution

Answer: (A) make the joint leak-proof against fluid pressure

Caulking hammers the plate edge against the adjacent plate to form a tight seal; it does not add strength.

Question 39

A shaft coupling is used to

  1. take the end thrust of the shaft in a bearing
  2. support the shaft against bending between the bearings
  3. join two shafts end to end to transmit torque
  4. reduce the diameter of the shaft at a step
Show answer & solution

Answer: (C) join two shafts end to end to transmit torque

Couplings connect separate shaft sections so power flows through continuously.

Question 40

A key between a shaft and a hub (pulley or gear) is used mainly to

  1. stop the hub turning on the shaft, so torque is transmitted
  2. carry the weight of the hub and any belt loads on the shaft
  3. increase the diameter of the shaft locally at the hub position
  4. damp the torsional vibration set up in the shaft at the hub
Show answer & solution

Answer: (A) stop the hub turning on the shaft, so torque is transmitted

The key locks the hub to the shaft rotationally so torque passes without slip.

Practice these 40 questions interactively →