What is thermal radiation?
Show answer & solution
Answer: (B) Energy emitted by matter as electromagnetic waves due to its temperature
It needs no medium and travels through vacuum.
Chemical Engineering · Heat Transfer
34 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is thermal radiation?
Answer: (B) Energy emitted by matter as electromagnetic waves due to its temperature
It needs no medium and travels through vacuum.
What does the Stefan–Boltzmann law state for a black body?
Answer: (C) Emissive power is proportional to the fourth power of absolute temperature
E = σT⁴, with σ = 5.67 × 10⁻⁸ W/(m²·K⁴).
What is the value of the Stefan–Boltzmann constant?
Answer: (C) 5.67 × 10⁻⁸ W/(m²·K⁴)
It applies to an ideal black body.
By what factor does the emissive power of a black body increase when its absolute temperature doubles?
Answer: (D) 16
E is proportional to T⁴.
What is a black body?
Answer: (B) An ideal surface that absorbs all incident radiation and emits the maximum possible at each temperature
Its absorptivity and emissivity are both 1.
What is a grey body?
Answer: (A) A surface whose emissivity is less than 1 but the same at all wavelengths
Real surfaces are often approximated as grey.
What does Kirchhoff's law of radiation state?
Answer: (D) At thermal equilibrium, emissivity of a surface equals its absorptivity
It applies at the same temperature and wavelength.
What is the sum of absorptivity, reflectivity and transmissivity of a surface?
Answer: (A) 1
For opaque surfaces, transmissivity is zero.
What does Wien's displacement law state?
Answer: (B) The wavelength of maximum emission is inversely proportional to absolute temperature
λmax T ≈ 2,898 μm·K.
At about what wavelength does the Sun (about 5,800 K) emit most strongly?
Answer: (B) About 0.5 μm (visible light)
Earth at about 300 K emits most near 10 μm.
What is the view factor (shape factor) in radiation?
Answer: (D) The fraction of radiation leaving one surface that reaches another directly
It depends only on geometry.
What does the reciprocity relation for view factors state?
Answer: (C) A₁F₁₂ = A₂F₂₁
It is used to find unknown view factors.
What is the view factor of a flat or convex surface to itself?
Answer: (A) Zero
A concave surface can see itself.
What is the effect of placing a radiation shield between two parallel surfaces?
Answer: (C) It reduces radiation heat transfer between them
One shield of the same emissivity halves the exchange.
Why are polished metal surfaces used to reduce radiation losses?
Answer: (D) They have low emissivity
Polished aluminium has emissivity around 0.05.
Which gases in furnace flue gas absorb and emit significant thermal radiation?
Answer: (A) Carbon dioxide and water vapour
Symmetric diatomic gases are nearly transparent.
What is the radiation heat flux from a black surface at 1,000 K to black surroundings at 0 K?
Answer: (C) About 56.7 kW/m²
σT⁴ = 5.67 × 10⁻⁸ × 10¹².
What is the radiation section of a fired heater?
Answer: (B) The firebox zone where tubes receive heat mainly by radiation from the flame
Most heat in refinery heaters is absorbed in the radiant section.
In which section of a fired heater is heat transferred mainly by convection from flue gas?
Answer: (D) Convection section above the radiant box
Finned tubes are often used in the convection section.
What is the emissivity of a surface?
Answer: (B) The ratio of its emissive power to that of a black body at the same temperature
It lies between 0 and 1.
What is the main principle of a solar water heater?
Answer: (A) Absorbing solar radiation on a dark selective surface under glass to heat water
Glass traps long-wave infrared radiation (greenhouse effect).
What is a selective surface in solar collectors?
Answer: (B) A surface with high absorptivity for solar radiation and low emissivity for infrared
It improves collector efficiency.
Why does a thermos (vacuum) flask keep liquids hot?
Answer: (D) The vacuum stops conduction and convection, and silvered walls reduce radiation
Losses occur mainly through the stopper.
What is the irradiation on a surface?
Answer: (C) The total radiant energy incident on the surface per unit area
Radiosity is the total radiation leaving a surface.
What is radiosity?
Answer: (A) The total radiation leaving a surface per unit area, emitted plus reflected
It is used in radiation network analysis.
Which instrument measures high temperatures in furnaces from emitted radiation without contact?
Answer: (C) Pyrometer
Optical and infrared pyrometers are common.
What is the net radiation exchange between two large parallel black plates at T₁ and T₂?
Answer: (B) σ(T₁⁴ − T₂⁴) per unit area
For grey plates, emissivities appear in the denominator.
What is the net radiation exchange between two large parallel grey plates with emissivities ε₁ and ε₂?
Answer: (A) σ(T₁⁴ − T₂⁴)/(1/ε₁ + 1/ε₂ − 1) per unit area
It reduces to the black-body case when both emissivities are 1.
What is the radiation loss from a small body of area A and emissivity ε in large surroundings?
Answer: (D) εσA(T⁴ − Tsurr⁴)
The surroundings act as a black body.
Why is snow nearly black to thermal infrared radiation although it looks white?
Answer: (B) Its emissivity in the infrared is very high, while it reflects visible light
Emissivity depends on wavelength.
What is Planck's law used for?
Answer: (A) Finding the spectral distribution of black body emissive power with wavelength
Integrating it over all wavelengths gives the Stefan–Boltzmann law.
What is the summation rule for view factors from a surface in an enclosure?
Answer: (D) The sum of view factors from that surface to all surfaces in the enclosure equals 1
All radiation leaving the surface must strike some surface.
What is a radiation heat transfer coefficient?
Answer: (C) A linearised coefficient hr so that radiation flux equals hr(T₁ − T₂)
hr ≈ 4εσTm³ for small temperature differences.
What fraction of radiation is reflected by an opaque surface with absorptivity 0.8?
Answer: (B) 0.2
For opaque surfaces α + ρ = 1.