Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Heat Transfer: Evaporators

Chemical Engineering · Heat Transfer

35 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the main purpose of an evaporator?

  1. To dry solids completely
  2. To crystallise without heating
  3. To cool gases
  4. To concentrate a solution by vaporising part of the solvent
Show answer & solution

Answer: (D) To concentrate a solution by vaporising part of the solvent

Examples include concentrating cane juice and caustic soda.

Question 2

In which Pakistani industry are multiple-effect evaporators widely used to concentrate juice?

  1. Sugar industry
  2. Textile weaving
  3. Cement industry
  4. Steel industry
Show answer & solution

Answer: (A) Sugar industry

Clarified cane juice is concentrated to syrup before crystallisation in vacuum pans.

Question 3

What is boiling point elevation in evaporation?

  1. The increase in steam temperature
  2. The rise in boiling point of a solution above that of the pure solvent at the same pressure
  3. The rise in liquid level
  4. The rise in pressure
Show answer & solution

Answer: (B) The rise in boiling point of a solution above that of the pure solvent at the same pressure

It reduces the available temperature difference.

Question 4

What is Dühring's rule used for in evaporation?

  1. Estimating the boiling point of a solution from the boiling point of water at the same pressure
  2. Finding the fouling factor
  3. Finding the steam economy
  4. Finding the heat transfer coefficient
Show answer & solution

Answer: (A) Estimating the boiling point of a solution from the boiling point of water at the same pressure

Dühring lines are nearly straight.

Question 5

What is steam economy of an evaporator?

  1. The cost of steam
  2. The steam pressure
  3. The area per effect
  4. The mass of water evaporated per unit mass of steam supplied
Show answer & solution

Answer: (D) The mass of water evaporated per unit mass of steam supplied

It rises roughly in proportion to the number of effects.

Question 6

What is the approximate steam economy of a single-effect evaporator?

  1. About 0.1
  2. About 5
  3. Slightly less than 1
  4. About 3
Show answer & solution

Answer: (C) Slightly less than 1

Each kg of steam evaporates nearly one kg of water.

Question 7

What is the main advantage of multiple-effect evaporation?

  1. No need for vacuum
  2. Higher steam economy, since vapour from one effect heats the next
  3. Higher capacity per unit area
  4. Lower capital cost
Show answer & solution

Answer: (B) Higher steam economy, since vapour from one effect heats the next

Total area increases with the number of effects.

Question 8

How does the capacity of a multiple-effect evaporator compare with a single effect of the same area per effect operating over the same overall temperature range?

  1. Proportionally greater capacity
  2. Zero capacity
  3. Much lower steam economy
  4. Roughly the same total capacity, though steam economy is higher
Show answer & solution

Answer: (D) Roughly the same total capacity, though steam economy is higher

The overall temperature drop is shared among the effects.

Question 9

What is forward feed in a multiple-effect evaporator?

  1. Feed enters every effect separately
  2. Feed and steam both enter the first effect and liquor flows in the same direction as vapour
  3. Feed enters the last effect
  4. Feed is recycled only
Show answer & solution

Answer: (B) Feed and steam both enter the first effect and liquor flows in the same direction as vapour

No pump is needed between effects because pressure falls along the train.

Question 10

When is backward feed preferred in multiple-effect evaporators?

  1. When the feed is cold or the concentrated product is very viscous
  2. When there is no vacuum
  3. When steam is free
  4. When the feed is hot and dilute
Show answer & solution

Answer: (A) When the feed is cold or the concentrated product is very viscous

The most concentrated liquor meets the hottest effect, keeping viscosity manageable.

Question 11

Why is the last effect of a multiple-effect evaporator operated under vacuum?

  1. To increase boiling point
  2. To stop boiling
  3. To lower the boiling point and increase the overall temperature difference
  4. To raise steam pressure
Show answer & solution

Answer: (C) To lower the boiling point and increase the overall temperature difference

A barometric or surface condenser and ejector maintain the vacuum.

Question 12

What is the main advantage of a falling-film evaporator?

  1. Use only for scaling liquids
  2. Short residence time and small temperature difference, suitable for heat-sensitive liquids
  3. High hydrostatic head
  4. Very long residence time
Show answer & solution

Answer: (B) Short residence time and small temperature difference, suitable for heat-sensitive liquids

Used for milk, juices and pharmaceuticals.

Question 13

Which evaporator is suited to scaling or crystallising liquors?

  1. Short-tube natural circulation without pump
  2. Plate evaporator
  3. Forced-circulation evaporator
  4. Falling-film evaporator
Show answer & solution

Answer: (C) Forced-circulation evaporator

High tube velocities and suppressed boiling in tubes reduce scaling.

Question 14

What is a calandria evaporator?

  1. A short-tube vertical evaporator with a central downcomer
  2. A plate evaporator
  3. A forced-circulation evaporator
  4. A falling-film evaporator
Show answer & solution

Answer: (A) A short-tube vertical evaporator with a central downcomer

It is the standard vertical evaporator used in sugar mills.

Question 15

What is mechanical vapour recompression (MVR)?

  1. Recycling liquor
  2. Condensing vapour in cooling water
  3. Using fresh steam only
  4. Compressing vapour from the evaporator so it can be used as the heating medium again
Show answer & solution

Answer: (D) Compressing vapour from the evaporator so it can be used as the heating medium again

It greatly reduces steam consumption.

Question 16

What is thermal vapour recompression?

  1. Heating with electricity
  2. Using a steam jet ejector to compress part of the vapour with motive steam for reuse as heating medium
  3. Cooling vapour with water
  4. Mechanical compression with fans
Show answer & solution

Answer: (B) Using a steam jet ejector to compress part of the vapour with motive steam for reuse as heating medium

It is simpler but less efficient than MVR.

Question 17

Why does hydrostatic head in tall evaporators reduce performance?

  1. It lowers pressure
  2. It increases the temperature difference
  3. It reduces boiling point
  4. It raises the boiling point of liquid in the lower part of the tubes, reducing temperature difference
Show answer & solution

Answer: (D) It raises the boiling point of liquid in the lower part of the tubes, reducing temperature difference

Short-tube and film evaporators minimise this effect.

Question 18

How much steam does a single-effect evaporator with economy 0.9 need to evaporate 9,000 kg/h of water?

  1. About 900 kg/h
  2. About 8,100 kg/h
  3. About 9,000 kg/h
  4. About 10,000 kg/h
Show answer & solution

Answer: (D) About 10,000 kg/h

Steam = 9,000/0.9.

Question 19

What is a barometric condenser?

  1. A cooling tower
  2. A refrigerator
  3. A direct-contact condenser at height so that a water leg of about 10 m seals the vacuum
  4. A surface condenser
Show answer & solution

Answer: (C) A direct-contact condenser at height so that a water leg of about 10 m seals the vacuum

The tailpipe discharges into a hot well.

Question 20

What is the function of an entrainment separator in an evaporator?

  1. To remove liquid droplets carried with the vapour
  2. To remove solids
  3. To pump liquor
  4. To heat liquor
Show answer & solution

Answer: (A) To remove liquid droplets carried with the vapour

It prevents product loss and fouling of the next effect.

Question 21

Which evaporator type is widely used to concentrate caustic soda?

  1. Solar pond
  2. Cooling tower
  3. Forced-circulation or falling-film evaporator made of nickel alloys
  4. Open pan
Show answer & solution

Answer: (C) Forced-circulation or falling-film evaporator made of nickel alloys

Caustic soda is highly corrosive at high concentration.

Question 22

What is the total temperature difference available in a multiple-effect evaporator?

  1. Steam temperature minus the saturation temperature in the last effect, minus boiling point elevations
  2. Zero
  3. Feed temperature only
  4. Steam temperature only
Show answer & solution

Answer: (A) Steam temperature minus the saturation temperature in the last effect, minus boiling point elevations

BPE in each effect reduces the useful driving force.

Question 23

What is a vacuum pan in sugar mills?

  1. A filter
  2. A single-effect evaporating crystalliser operated under vacuum to grow sugar crystals
  3. A dryer
  4. A juice heater only
Show answer & solution

Answer: (B) A single-effect evaporating crystalliser operated under vacuum to grow sugar crystals

Low boiling temperature limits sucrose inversion and colour.

Question 24

Why are heat-sensitive products such as milk evaporated under vacuum?

  1. Vacuum sterilises
  2. Vacuum increases the boiling point
  3. Lower boiling temperatures reduce thermal damage
  4. Vacuum adds flavour
Show answer & solution

Answer: (C) Lower boiling temperatures reduce thermal damage

Combined with short residence time in film evaporators.

Question 25

What does a rising-film (climbing-film) evaporator rely on?

  1. Vapour generated in long vertical tubes carrying a liquid film upward
  2. A pump for film flow
  3. Gravity for downward flow
  4. Mechanical wiping
Show answer & solution

Answer: (A) Vapour generated in long vertical tubes carrying a liquid film upward

It is used for low-viscosity foaming liquids.

Question 26

What is an agitated thin-film evaporator used for?

  1. Steam generation
  2. Very viscous or heat-sensitive materials, using wiper blades to spread a thin film
  3. Gas drying
  4. Low-viscosity water only
Show answer & solution

Answer: (B) Very viscous or heat-sensitive materials, using wiper blades to spread a thin film

It is used for polymers and pharmaceuticals.

Question 27

How does the heat transfer coefficient in evaporators change as liquor becomes more concentrated?

  1. It becomes infinite
  2. It increases sharply
  3. It stays constant
  4. It generally decreases due to higher viscosity
Show answer & solution

Answer: (D) It generally decreases due to higher viscosity

This is why backward feed suits viscous products.

Question 28

Why is condensate from evaporator steam chests returned to the boiler?

  1. It is cold
  2. It contains product
  3. It is hot, clean water that saves energy and treatment costs
  4. It is waste only
Show answer & solution

Answer: (C) It is hot, clean water that saves energy and treatment costs

Contaminated condensate must be checked first.

Question 29

What is the heat load of an evaporator mainly used for?

  1. Supplying latent heat to vaporise the solvent and sensible heat to bring feed to boiling
  2. Heating the shell only
  3. Pumping liquor
  4. Cooling the product
Show answer & solution

Answer: (A) Supplying latent heat to vaporise the solvent and sensible heat to bring feed to boiling

Q = steam flow × steam latent heat.

Question 30

How does preheating cold feed affect a single-effect evaporator?

  1. It stops boiling
  2. It increases steam consumption
  3. It has no effect
  4. It reduces steam needed per kg of water evaporated
Show answer & solution

Answer: (D) It reduces steam needed per kg of water evaporated

Less sensible heating is needed inside the evaporator.

Question 31

What causes foaming problems in evaporators?

  1. Clean steam
  2. Low viscosity water
  3. High vacuum only
  4. Surface-active substances in the liquor that stabilise bubbles
Show answer & solution

Answer: (D) Surface-active substances in the liquor that stabilise bubbles

Antifoam agents and foam breakers are used.

Question 32

What is the typical number of effects in a sugar mill evaporator station?

  1. One effect only
  2. About four or five effects
  3. About twenty effects
  4. Ten effects with no vacuum
Show answer & solution

Answer: (B) About four or five effects

Vapour from effects is also bled to juice heaters and vacuum pans.

Question 33

What is vapour bleeding in a multiple-effect evaporator?

  1. Withdrawing part of the vapour from an effect to heat other process equipment
  2. Venting non-condensables only
  3. Removing condensate
  4. Leaking of steam
Show answer & solution

Answer: (A) Withdrawing part of the vapour from an effect to heat other process equipment

It improves overall plant steam economy in sugar mills.

Question 34

Why must non-condensable gases be vented from evaporator steam chests?

  1. They increase heat transfer
  2. They lower the vacuum harmlessly
  3. They accumulate and reduce the condensing heat transfer coefficient
  4. They cause boiling point elevation
Show answer & solution

Answer: (C) They accumulate and reduce the condensing heat transfer coefficient

Ammonia and air are released from juice and steam.

Question 35

What is the most common material of construction for evaporators in sugar plants?

  1. Glass
  2. Concrete
  3. Mild steel with stainless steel or brass tubes
  4. Wood
Show answer & solution

Answer: (C) Mild steel with stainless steel or brass tubes

Tube material is chosen for heat transfer and corrosion resistance.

Practice these 35 questions interactively →