Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Heat Transfer: Conduction

Chemical Engineering · Heat Transfer

36 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What are the three basic modes of heat transfer?

  1. Radiation, boiling and condensation
  2. Convection, absorption and reflection
  3. Conduction, evaporation and diffusion
  4. Conduction, convection and radiation
Show answer & solution

Answer: (D) Conduction, convection and radiation

Boiling and condensation are forms of convection with phase change.

Question 2

What does Fourier's law of heat conduction state?

  1. Heat flux is independent of the material
  2. Heat flux is proportional to the negative temperature gradient
  3. Heat flux is proportional to fluid velocity
  4. Heat flux is proportional to the temperature difference to the fourth power
Show answer & solution

Answer: (B) Heat flux is proportional to the negative temperature gradient

q = −k (dT/dx).

Question 3

What is the SI unit of thermal conductivity?

  1. W/(m²·K)
  2. J/(kg·K)
  3. W/(m·K)
  4. m²/s
Show answer & solution

Answer: (C) W/(m·K)

Heat transfer coefficients use W/(m²·K).

Question 4

Which material has the highest thermal conductivity among these?

  1. Copper
  2. Brick
  3. Stainless steel
  4. Glass
Show answer & solution

Answer: (A) Copper

Copper is about 385–400 W/(m·K).

Question 5

What is the approximate thermal conductivity of still air at room temperature?

  1. About 0.026 W/(m·K)
  2. About 0.6 W/(m·K)
  3. About 50 W/(m·K)
  4. About 400 W/(m·K)
Show answer & solution

Answer: (A) About 0.026 W/(m·K)

Trapped air makes insulating materials effective.

Question 6

What is the approximate thermal conductivity of water at room temperature?

  1. About 0.026 W/(m·K)
  2. About 0.6 W/(m·K)
  3. About 45 W/(m·K)
  4. About 385 W/(m·K)
Show answer & solution

Answer: (B) About 0.6 W/(m·K)

Liquids conduct better than gases but far worse than metals.

Question 7

How does the thermal conductivity of most pure metals change with rising temperature?

  1. It increases sharply
  2. It becomes zero
  3. It decreases
  4. It stays exactly constant
Show answer & solution

Answer: (C) It decreases

For gases conductivity rises with temperature.

Question 8

What is the rate of heat conduction through a plane wall 0.2 m thick, 10 m² in area, with k = 1 W/(m·K) and a temperature difference of 40 K?

  1. 80 W
  2. 200 W
  3. 2,000 W
  4. 8,000 W
Show answer & solution

Answer: (C) 2,000 W

Q = kAΔT/L = 1 × 10 × 40/0.2.

Question 9

What is the thermal resistance of a plane wall?

  1. hA
  2. kA/L
  3. L/k only
  4. L/(kA)
Show answer & solution

Answer: (D) L/(kA)

Resistances in series add, like electrical resistances.

Question 10

How is the total thermal resistance of a composite wall of layers in series found?

  1. By adding the individual layer resistances
  2. By adding the conductivities
  3. By taking the largest resistance only
  4. By multiplying the resistances
Show answer & solution

Answer: (A) By adding the individual layer resistances

Q = ΔT_overall/ΣR.

Question 11

What is the thermal resistance for radial conduction through a cylindrical shell?

  1. (r₂ − r₁)/(kA)
  2. ln(r₂/r₁)/(2πkL)
  3. 1/(hA)
  4. 2πkL/ln(r₂/r₁)
Show answer & solution

Answer: (B) ln(r₂/r₁)/(2πkL)

The temperature profile is logarithmic.

Question 12

What is the temperature profile for steady one-dimensional conduction through a plane wall with constant k and no heat generation?

  1. Parabolic
  2. Exponential
  3. Logarithmic
  4. Linear
Show answer & solution

Answer: (D) Linear

It is logarithmic in a cylinder.

Question 13

What is thermal diffusivity?

  1. k/(ρCp), indicating how fast temperature changes spread through a material
  2. h/k
  3. ρCp/k
  4. k × ρ
Show answer & solution

Answer: (A) k/(ρCp), indicating how fast temperature changes spread through a material

Its unit is m²/s.

Question 14

What is the critical radius of insulation for a cylinder?

  1. 2k/h
  2. h/k
  3. k/h, where k is the insulation conductivity and h the outside coefficient
  4. k × h
Show answer & solution

Answer: (C) k/h, where k is the insulation conductivity and h the outside coefficient

Adding insulation below this radius increases heat loss.

Question 15

What is the critical radius of insulation for a sphere?

  1. k/(2h)
  2. 2k/h
  3. h/k
  4. k/h
Show answer & solution

Answer: (B) 2k/h

It is twice the cylinder value.

Question 16

Why can adding thin insulation to a small electrical wire increase heat loss?

  1. Insulation conducts heat better than copper
  2. Air stops convection
  3. Insulation reflects heat inward
  4. The wire radius is below the critical radius, so added surface area outweighs added resistance
Show answer & solution

Answer: (D) The wire radius is below the critical radius, so added surface area outweighs added resistance

This helps cool electrical cables.

Question 17

What is the Biot number?

  1. hL/k_fluid
  2. ν/α
  3. ρVL/μ
  4. hL/k_solid, comparing internal conduction resistance with surface convection resistance
Show answer & solution

Answer: (D) hL/k_solid, comparing internal conduction resistance with surface convection resistance

Lumped analysis is valid when Bi < 0.1.

Question 18

When can the lumped-capacitance method be used for transient conduction?

  1. When the Biot number is greater than 10
  2. Only for liquids
  3. When the Biot number is less than about 0.1
  4. Only at steady state
Show answer & solution

Answer: (C) When the Biot number is less than about 0.1

Temperature inside the solid is then nearly uniform.

Question 19

What is the Fourier number?

  1. αt/L², a dimensionless time for transient conduction
  2. hL/k
  3. ρVL/μ
  4. Cpμ/k
Show answer & solution

Answer: (A) αt/L², a dimensionless time for transient conduction

Heisler charts use Bi and Fo.

Question 20

Which charts give centre temperatures in transient conduction of slabs, cylinders and spheres?

  1. Mollier charts
  2. Heisler charts
  3. Moody charts
  4. Cox charts
Show answer & solution

Answer: (B) Heisler charts

Gröber charts give heat transferred.

Question 21

What is the purpose of fins on a heat transfer surface?

  1. To increase the surface area and so the heat transfer rate
  2. To reduce the area
  3. To increase thermal resistance
  4. To prevent fouling
Show answer & solution

Answer: (A) To increase the surface area and so the heat transfer rate

Fins are most useful on the side with low heat transfer coefficient.

Question 22

What is fin efficiency?

  1. The conductivity of the fin
  2. The ratio of fin area to base area
  3. The ratio of fin length to thickness
  4. The ratio of actual fin heat transfer to the heat transfer if the whole fin were at base temperature
Show answer & solution

Answer: (D) The ratio of actual fin heat transfer to the heat transfer if the whole fin were at base temperature

Long thin fins of low-k material have low efficiency.

Question 23

On which side of an air-cooled heat exchanger are fins placed?

  1. Neither side
  2. The water side
  3. The air side
  4. Both sides equally always
Show answer & solution

Answer: (C) The air side

Air has a much lower heat transfer coefficient than liquids.

Question 24

Which material is commonly used to insulate high-temperature steam pipes?

  1. Aluminium sheet only
  2. Mineral wool or calcium silicate
  3. Glass panes
  4. Copper
Show answer & solution

Answer: (B) Mineral wool or calcium silicate

Aluminium cladding protects the insulation from weather.

Question 25

What is the main function of refractory bricks in a furnace?

  1. To withstand high temperatures and reduce heat loss through the walls
  2. To conduct heat out quickly
  3. To store fuel
  4. To measure temperature
Show answer & solution

Answer: (A) To withstand high temperatures and reduce heat loss through the walls

Fire clay and alumina bricks are common.

Question 26

What happens to heat loss if insulation thickness on a large pipe is increased?

  1. It becomes zero
  2. It increases continuously
  3. It decreases, but with diminishing returns
  4. It stays the same
Show answer & solution

Answer: (C) It decreases, but with diminishing returns

The economic thickness balances insulation cost and energy saving.

Question 27

What is the economic thickness of insulation?

  1. The maximum thickness available
  2. The thickness that minimises the total cost of insulation and lost heat
  3. The critical radius
  4. The thickness of the pipe wall
Show answer & solution

Answer: (B) The thickness that minimises the total cost of insulation and lost heat

It depends on fuel cost and insulation price.

Question 28

What is contact (interface) resistance?

  1. The resistance of a fluid film
  2. The resistance of insulation
  3. The resistance of radiation
  4. The extra resistance to heat flow at the joint between two solid surfaces
Show answer & solution

Answer: (D) The extra resistance to heat flow at the joint between two solid surfaces

It is reduced by thermal paste or higher contact pressure.

Question 29

How does heat flow through layers in parallel (side by side) combine?

  1. Heat flow is zero
  2. Resistances add
  3. Conductances add, so the reciprocal of total resistance is the sum of reciprocals
  4. Only the largest path conducts
Show answer & solution

Answer: (C) Conductances add, so the reciprocal of total resistance is the sum of reciprocals

This is like parallel electrical resistors.

Question 30

What is the heat generation term in Fourier's equation used for?

  1. Only radiation
  2. Only fluid flow
  3. Only fin analysis
  4. Situations such as electrical heating of wires or nuclear fuel rods
Show answer & solution

Answer: (D) Situations such as electrical heating of wires or nuclear fuel rods

It gives a parabolic temperature profile in a slab.

Question 31

What is the heat flow through a cylindrical pipe insulation with ln(r₂/r₁) = 0.5, k = 0.05 W/(m·K), length 1 m and temperature difference 100 K?

  1. About 10 W
  2. About 31.4 W
  3. About 62.8 W
  4. About 628 W
Show answer & solution

Answer: (C) About 62.8 W

Q = 2πkLΔT/ln(r₂/r₁) = 2π × 0.05 × 100/0.5.

Question 32

What is the temperature drop across each layer of a composite wall proportional to?

  1. Its thermal resistance
  2. Its density
  3. Its heat capacity
  4. Its area only
Show answer & solution

Answer: (A) Its thermal resistance

The same heat flow passes through each layer in series.

Question 33

What is the overall heat transfer through a wall with inside film, wall and outside film resistances?

  1. The difference of the resistances
  2. The product of the resistances
  3. The largest resistance only
  4. ΔT_overall divided by the sum of the three resistances
Show answer & solution

Answer: (D) ΔT_overall divided by the sum of the three resistances

This is the basis of the overall coefficient U.

Question 34

What is the semi-infinite solid assumption in transient conduction?

  1. A thin plate
  2. A body with no thermal mass
  3. A body so thick that the temperature disturbance does not reach its far side during the time considered
  4. A body with uniform temperature
Show answer & solution

Answer: (C) A body so thick that the temperature disturbance does not reach its far side during the time considered

The solution uses the error function.

Question 35

What is the difference between steady and unsteady state conduction?

  1. They are the same
  2. In steady state temperatures do not change with time; in unsteady state they do
  3. Unsteady state has constant temperature
  4. Steady state has no heat flow
Show answer & solution

Answer: (B) In steady state temperatures do not change with time; in unsteady state they do

Heating and cooling of solids are unsteady processes.

Question 36

Which equation governs transient conduction in a solid with constant properties and no generation?

  1. ∇²T = 0 only
  2. E = σT⁴
  3. q = hAΔT
  4. ∂T/∂t = α∇²T
Show answer & solution

Answer: (D) ∂T/∂t = α∇²T

At steady state it reduces to Laplace's equation.

Practice these 36 questions interactively →