What is pool boiling?
Show answer & solution
Answer: (D) Boiling of a stagnant liquid on a heated surface immersed in it
Flow boiling occurs in tubes.
Chemical Engineering · Heat Transfer
32 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is pool boiling?
Answer: (D) Boiling of a stagnant liquid on a heated surface immersed in it
Flow boiling occurs in tubes.
Which regime of pool boiling has the highest heat transfer coefficients in practice?
Answer: (B) Nucleate boiling
Bubbles agitate the liquid near the surface.
What is the critical (peak) heat flux in boiling?
Answer: (A) The maximum heat flux in nucleate boiling, beyond which a vapour film forms
Exceeding it can cause tube burnout.
What is film boiling?
Answer: (B) Boiling in which a continuous vapour film covers the heated surface
The vapour film acts as insulation.
What is the Leidenfrost effect?
Answer: (D) A liquid drop skating on a very hot surface on a cushion of its own vapour
It shows the onset of film boiling.
What is the excess temperature in boiling?
Answer: (A) The difference between surface temperature and saturation temperature of the liquid
The boiling curve plots heat flux against excess temperature.
Which chart shows heat flux against excess temperature in pool boiling?
Answer: (C) The boiling (Nukiyama) curve
Nukiyama first obtained it with electrically heated wires.
What is filmwise condensation?
Answer: (D) Condensation in which the condensate forms a continuous liquid film on the surface
Most condensers are designed for filmwise condensation.
Which type of condensation gives a higher heat transfer coefficient?
Answer: (B) Dropwise condensation
Drops leave bare surface exposed to vapour, but dropwise is hard to sustain.
Whose theory gives heat transfer coefficients for laminar film condensation on vertical surfaces?
Answer: (A) Nusselt
It assumes a laminar film draining by gravity.
Why is a horizontal tube preferred to a vertical tube for condensation on the outside?
Answer: (C) The condensate film is thinner, giving a higher coefficient
For tube bundles, condensate dripping from upper rows thickens films lower down.
What is the effect of non-condensable gases such as air in a steam condenser?
Answer: (C) They greatly reduce the condensing heat transfer coefficient
Air accumulates at the surface and adds resistance; vents remove it.
Why is superheat in steam of little benefit for heat transfer in process heating?
Answer: (D) Most heat is given up as latent heat at constant temperature, and superheated vapour has a low coefficient
Saturated steam is preferred for process heating.
What is a steam trap?
Answer: (B) A device that discharges condensate and non-condensables while retaining live steam
Thermostatic, thermodynamic and float traps are common.
What is subcooled boiling?
Answer: (A) Boiling at a heated surface while the bulk liquid is below saturation temperature
Bubbles collapse in the cooler bulk liquid.
What is burnout in boiling?
Answer: (B) Damage to a heated surface when heat flux exceeds the critical heat flux under controlled flux
It is a key safety limit in boilers and nuclear reactors.
What is the latent heat released by condensing 1 kg of steam at 100 °C?
Answer: (D) About 2,257 kJ
Higher-pressure steam releases less latent heat per kilogram.
How does the latent heat of steam change as pressure increases?
Answer: (C) It decreases
At the critical point it becomes zero.
What is flow boiling?
Answer: (A) Boiling of a liquid flowing through a heated channel or tube
Regimes include bubbly, slug, annular and mist flow.
What is the effect of surface roughness on nucleate boiling?
Answer: (A) More cavities give more nucleation sites and higher heat transfer
Enhanced boiling surfaces exploit this.
What is the minimum heat flux (Leidenfrost point) on the boiling curve?
Answer: (A) The lowest heat flux in the film boiling regime, between transition and stable film boiling
Below it the vapour film becomes unstable.
In which pool boiling regime does heat flux fall as excess temperature rises?
Answer: (D) Transition boiling
The surface alternates between nucleate and film boiling.
What heat transfer mechanism becomes important in film boiling at very high surface temperatures?
Answer: (B) Radiation across the vapour film
Radiation adds significantly above about 300 °C excess temperature.
Which correlation is commonly used for nucleate pool boiling heat flux?
Answer: (B) Rohsenow correlation
It includes a surface–fluid constant Csf.
Which correlation estimates the critical heat flux in pool boiling?
Answer: (A) Zuber (Kutateladze) correlation
It depends on latent heat, densities and surface tension.
How does increasing system pressure generally affect the critical heat flux of water up to moderate pressures?
Answer: (C) It increases it
CHF peaks at about one-third of the critical pressure.
What is the effect of condensate film thickness on the condensing heat transfer coefficient?
Answer: (D) A thicker film reduces the coefficient
The film is the main resistance to heat flow.
How does the condensing coefficient on a vertical surface vary with height in laminar film condensation?
Answer: (A) It decreases as the film thickens down the surface
The local coefficient varies with height to the power −1/4.
What can promote dropwise condensation on a surface?
Answer: (D) Coating the surface with a non-wetting (hydrophobic) promoter
Promoters wear off, so filmwise design is normally used.
Where is condensation heat transfer used in a thermal power plant?
Answer: (B) In the surface condenser at the turbine exhaust
Condensing under vacuum lets the turbine expand steam further.
What is the approximate saturation temperature of steam at 10 bar absolute?
Answer: (C) About 180 °C
Steam tables give 179.9 °C.
What is a total condenser in a distillation column?
Answer: (C) A condenser that condenses all the overhead vapour to liquid
A partial condenser acts as an extra equilibrium stage.