Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Heat Transfer: Convection

Chemical Engineering · Heat Transfer

36 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is convection?

  1. Heat transfer between a surface and a moving fluid, combining conduction and fluid motion
  2. Heat transfer through a solid only
  3. Heat transfer by electromagnetic waves only
  4. Heat transfer through vacuum
Show answer & solution

Answer: (A) Heat transfer between a surface and a moving fluid, combining conduction and fluid motion

It is described by Newton's law of cooling.

Question 2

What does Newton's law of cooling state?

  1. Heat flux equals σT⁴
  2. Heat transfer rate equals hAΔT
  3. Heat flux equals −k dT/dx
  4. Heat transfer rate equals ṁλ
Show answer & solution

Answer: (B) Heat transfer rate equals hAΔT

h is the convective heat transfer coefficient.

Question 3

What is the difference between natural and forced convection?

  1. Natural convection needs a fan
  2. Natural convection is driven by buoyancy from density differences; forced convection uses pumps or fans
  3. They are identical
  4. Forced convection needs gravity
Show answer & solution

Answer: (B) Natural convection is driven by buoyancy from density differences; forced convection uses pumps or fans

Forced convection gives much higher coefficients.

Question 4

What is the Nusselt number?

  1. ρVL/μ
  2. Cpμ/k
  3. hL/k_fluid, the ratio of convective to conductive heat transfer
  4. hL/k_solid
Show answer & solution

Answer: (C) hL/k_fluid, the ratio of convective to conductive heat transfer

Correlations express Nu in terms of Re and Pr.

Question 5

What is the Prandtl number?

  1. Cpμ/k, the ratio of momentum diffusivity to thermal diffusivity
  2. ρVL/μ
  3. hL/k
  4. gβΔTL³/ν²
Show answer & solution

Answer: (A) Cpμ/k, the ratio of momentum diffusivity to thermal diffusivity

It is about 0.7 for gases and about 7 for water at room temperature.

Question 6

What is the approximate Prandtl number of air?

  1. About 0.01
  2. About 0.7
  3. About 7
  4. About 100
Show answer & solution

Answer: (B) About 0.7

Liquid metals have very low Prandtl numbers.

Question 7

Which fluids have very low Prandtl numbers (much less than 1)?

  1. Water
  2. Glycerine
  3. Heavy oils
  4. Liquid metals
Show answer & solution

Answer: (D) Liquid metals

Their conduction is very high relative to momentum diffusion.

Question 8

What is the Grashof number?

  1. Cpμ/k
  2. ρVL/μ
  3. gβΔTL³/ν², the ratio of buoyancy to viscous forces
  4. hL/k
Show answer & solution

Answer: (C) gβΔTL³/ν², the ratio of buoyancy to viscous forces

It governs natural convection.

Question 9

What is the Rayleigh number?

  1. The ratio of Nu to Re
  2. Bi × Fo
  3. Re × Pr
  4. The product of the Grashof and Prandtl numbers
Show answer & solution

Answer: (D) The product of the Grashof and Prandtl numbers

Natural convection correlations use Ra.

Question 10

Which correlation is widely used for turbulent forced convection inside tubes?

  1. Dittus–Boelter equation, Nu = 0.023Re^0.8 Prⁿ
  2. Stokes' law
  3. Antoine equation
  4. Kozeny–Carman equation
Show answer & solution

Answer: (A) Dittus–Boelter equation, Nu = 0.023Re^0.8 Prⁿ

n = 0.4 for heating and 0.3 for cooling of the fluid.

Question 11

In the Dittus–Boelter equation, what exponent is used on the Prandtl number when the fluid is being heated?

  1. 0.3
  2. 0.33
  3. 0.4
  4. 0.8
Show answer & solution

Answer: (C) 0.4

0.3 is used when the fluid is being cooled.

Question 12

What is the Nusselt number for fully developed laminar flow in a tube with constant wall temperature?

  1. About 0.023
  2. About 3.66
  3. About 4.36
  4. About 100
Show answer & solution

Answer: (B) About 3.66

It is about 4.36 for constant heat flux.

Question 13

What is the Stanton number?

  1. Nu/(Re × Pr), or h/(ρVCp)
  2. Re × Pr
  3. hL/k
  4. Gr × Pr
Show answer & solution

Answer: (A) Nu/(Re × Pr), or h/(ρVCp)

It appears in the Colburn analogy.

Question 14

What does the Colburn j-factor analogy relate?

  1. Conduction to radiation
  2. Boiling to condensation
  3. Mass transfer to radiation
  4. Heat transfer to fluid friction: jH = St Pr^(2/3) = f/2 (Fanning)
Show answer & solution

Answer: (D) Heat transfer to fluid friction: jH = St Pr^(2/3) = f/2 (Fanning)

It allows h to be estimated from friction data.

Question 15

What is the Reynolds analogy?

  1. A law of radiation
  2. An analogy between momentum transfer and heat transfer, valid for Pr = 1
  3. A law of boiling
  4. An analogy between conduction and radiation
Show answer & solution

Answer: (B) An analogy between momentum transfer and heat transfer, valid for Pr = 1

St = f/2 for Pr = 1.

Question 16

What is the Peclet number?

  1. The product of Grashof and Prandtl numbers
  2. The ratio of Nu to Pr
  3. The product of the Reynolds and Prandtl numbers
  4. The ratio of h to k
Show answer & solution

Answer: (C) The product of the Reynolds and Prandtl numbers

It compares advection to diffusion of heat.

Question 17

What is the Graetz number used for?

  1. Laminar heat transfer in the entrance region of tubes
  2. Boiling
  3. Radiation
  4. Natural convection
Show answer & solution

Answer: (A) Laminar heat transfer in the entrance region of tubes

Gz = Re Pr D/L.

Question 18

What is the thermal boundary layer?

  1. The insulation layer
  2. The scale layer
  3. The region of velocity change only
  4. The region near a surface where the fluid temperature changes from the wall value to the free-stream value
Show answer & solution

Answer: (D) The region near a surface where the fluid temperature changes from the wall value to the free-stream value

Its thickness relative to the velocity boundary layer depends on Pr.

Question 19

How does the convective heat transfer coefficient generally change as fluid velocity increases in forced convection?

  1. It becomes zero
  2. It increases
  3. It decreases
  4. It stays constant
Show answer & solution

Answer: (B) It increases

In turbulent tube flow h varies roughly with V^0.8.

Question 20

Which typically has the highest heat transfer coefficient?

  1. Natural convection in air
  2. Forced convection in oil
  3. Condensing steam
  4. Forced convection in air
Show answer & solution

Answer: (C) Condensing steam

Condensing steam has about 5,000–100,000 W/(m²·K).

Question 21

What is the typical range of heat transfer coefficient for natural convection in air?

  1. About 5 to 25 W/(m²·K)
  2. About 1,000 W/(m²·K)
  3. About 5,000 to 10,000 W/(m²·K)
  4. About 100,000 W/(m²·K)
Show answer & solution

Answer: (A) About 5 to 25 W/(m²·K)

This is why air coolers need large finned areas.

Question 22

What is the heat transfer rate from a surface of 2 m² at 80 °C to air at 30 °C with h = 10 W/(m²·K)?

  1. 100 W
  2. 500 W
  3. 1,000 W
  4. 1,600 W
Show answer & solution

Answer: (C) 1,000 W

Q = 10 × 2 × 50.

Question 23

What is the bulk (mixing-cup) temperature of a fluid in a tube?

  1. The average of inlet and outlet wall temperatures
  2. The centreline temperature only
  3. The wall temperature
  4. The temperature that the fluid would reach if fully mixed across the section
Show answer & solution

Answer: (D) The temperature that the fluid would reach if fully mixed across the section

It is used with h for tube flow.

Question 24

What is the Sieder–Tate correction for?

  1. Natural convection only
  2. The effect of viscosity variation between bulk and wall temperatures
  3. Fouling
  4. Radiation effects
Show answer & solution

Answer: (B) The effect of viscosity variation between bulk and wall temperatures

It multiplies Nu by (μ/μw)^0.14.

Question 25

In natural convection from a vertical plate, which flow regime occurs at Rayleigh numbers above about 10⁹?

  1. Stagnant
  2. Creeping
  3. Laminar
  4. Turbulent
Show answer & solution

Answer: (D) Turbulent

Below about 10⁹ the flow is laminar.

Question 26

What causes buoyancy in natural convection?

  1. Density differences due to temperature differences in the fluid
  2. Magnetic fields
  3. External pumps
  4. Radiation pressure
Show answer & solution

Answer: (A) Density differences due to temperature differences in the fluid

Hot fluid rises and cold fluid sinks.

Question 27

What is the coefficient of volumetric thermal expansion β for an ideal gas?

  1. Cp/Cv
  2. T
  3. R/P
  4. 1/T, with T in absolute units
Show answer & solution

Answer: (D) 1/T, with T in absolute units

It appears in the Grashof number.

Question 28

Why are tube-side velocities kept high in heat exchangers within pressure drop limits?

  1. To prevent turbulence
  2. To decrease heat transfer
  3. To increase heat transfer coefficients and reduce fouling
  4. To reduce pumping power
Show answer & solution

Answer: (C) To increase heat transfer coefficients and reduce fouling

Pressure drop rises roughly with velocity squared.

Question 29

How does heat transfer in turbulent flow compare with laminar flow at the same conditions?

  1. It is much higher due to eddy mixing
  2. It is the same
  3. It is zero
  4. It is lower
Show answer & solution

Answer: (A) It is much higher due to eddy mixing

Turbulence thins the laminar sublayer that controls resistance.

Question 30

What are typical heat transfer coefficients for forced convection of water?

  1. About 0.1 W/(m²·K)
  2. About 5 to 25 W/(m²·K)
  3. About 10⁶ W/(m²·K)
  4. About 500 to 10,000 W/(m²·K)
Show answer & solution

Answer: (D) About 500 to 10,000 W/(m²·K)

Values depend strongly on velocity and geometry.

Question 31

For turbulent flow inside a tube at a given mass flow, how does h vary with tube diameter according to Dittus–Boelter?

  1. Roughly in proportion to D^(−1.8)
  2. Roughly in proportion to D²
  3. Roughly in proportion to D
  4. Independently of D
Show answer & solution

Answer: (A) Roughly in proportion to D^(−1.8)

Smaller tubes give higher velocity and coefficient but more pressure drop.

Question 32

What correlation is used for flow across tube banks on the shell side?

  1. Kern or Bell–Delaware methods
  2. Dittus–Boelter for tubes only
  3. Stefan–Boltzmann law
  4. Nusselt condensation theory
Show answer & solution

Answer: (A) Kern or Bell–Delaware methods

Bell–Delaware accounts for leakage and bypass streams.

Question 33

What is mixed convection?

  1. Boiling and condensation together
  2. Heat transfer in which natural and forced convection are both significant
  3. Convection with radiation only
  4. Conduction with radiation
Show answer & solution

Answer: (B) Heat transfer in which natural and forced convection are both significant

It occurs when Gr/Re² is of order one.

Question 34

Which ratio indicates whether natural convection is significant compared with forced convection?

  1. St × Pr
  2. Nu/Pr
  3. Gr/Re²
  4. Bi/Fo
Show answer & solution

Answer: (C) Gr/Re²

Natural convection dominates when Gr/Re² ≫ 1.

Question 35

How does the heat transfer coefficient vary along a flat plate in laminar flow from the leading edge?

  1. It increases
  2. It is zero at the leading edge
  3. It decreases as the boundary layer thickens
  4. It is constant
Show answer & solution

Answer: (C) It decreases as the boundary layer thickens

Local h varies with x^(−1/2).

Question 36

Why is an oil cooler on the oil side often the controlling resistance?

  1. Water has a low coefficient
  2. Oil has high viscosity and low conductivity, giving low film coefficients
  3. Oil boils easily
  4. Oil has very high conductivity
Show answer & solution

Answer: (B) Oil has high viscosity and low conductivity, giving low film coefficients

Turbulators or fins may be used on the oil side.

Practice these 36 questions interactively →