Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Process Control & Instrumentation: Feedback and PID Control

Chemical Engineering · Process Control & Instrumentation

34 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is feedback control?

  1. Manual control only
  2. Control based on measuring disturbances only
  3. Control without measurement
  4. Control in which the controlled variable is measured and compared with the set point to adjust the manipulated variable
Show answer & solution

Answer: (D) Control in which the controlled variable is measured and compared with the set point to adjust the manipulated variable

It corrects for all disturbances after they affect the process.

Question 2

What is the set point?

  1. The desired value of the controlled variable
  2. The measured value
  3. The error
  4. The valve position
Show answer & solution

Answer: (A) The desired value of the controlled variable

Error = set point − measured value.

Question 3

What is the manipulated variable?

  1. The variable adjusted by the controller to keep the controlled variable at set point
  2. The variable being controlled
  3. The disturbance
  4. The set point
Show answer & solution

Answer: (A) The variable adjusted by the controller to keep the controlled variable at set point

Usually a flow adjusted by a control valve.

Question 4

What is a disturbance (load) variable?

  1. The manipulated variable
  2. The set point
  3. The controller output
  4. An input that affects the controlled variable but is not adjusted by the controller
Show answer & solution

Answer: (D) An input that affects the controlled variable but is not adjusted by the controller

Feed composition changes are typical disturbances.

Question 5

What is offset in proportional control?

  1. The rise time
  2. A sustained steady-state error between set point and controlled variable
  3. The overshoot
  4. The dead time
Show answer & solution

Answer: (B) A sustained steady-state error between set point and controlled variable

Proportional-only control usually leaves offset for load changes.

Question 6

What is the transfer function of an ideal PID controller?

  1. Kc e^(−θs)
  2. Kc s
  3. Kc(1 + 1/(τIs) + τDs)
  4. Kc/(τs + 1)
Show answer & solution

Answer: (C) Kc(1 + 1/(τIs) + τDs)

τI is integral time and τD derivative time.

Question 7

What is the main advantage of integral action?

  1. It reduces noise sensitivity
  2. It speeds up response without overshoot always
  3. It eliminates offset
  4. It anticipates future errors
Show answer & solution

Answer: (C) It eliminates offset

It may cause overshoot and reset windup.

Question 8

What is the main purpose of derivative action?

  1. It anticipates the error by responding to its rate of change, improving stability
  2. It increases noise
  3. It slows the response
  4. It removes offset
Show answer & solution

Answer: (A) It anticipates the error by responding to its rate of change, improving stability

It is avoided on noisy signals such as flow.

Question 9

Why is derivative action seldom used in flow control loops?

  1. Derivative action removes offset
  2. Flow signals are noisy and the process is fast
  3. Flow loops have large dead time
  4. Flow loops are integrating
Show answer & solution

Answer: (B) Flow signals are noisy and the process is fast

PI control is standard for flow.

Question 10

Which controller mode is most common in liquid flow control?

  1. P only
  2. On–off
  3. PD
  4. PI
Show answer & solution

Answer: (D) PI

Flow loops are fast and noisy.

Question 11

What is proportional band?

  1. The controller gain in all units
  2. The integral time
  3. The percentage change in input needed to drive the controller output through its full range
  4. The derivative time
Show answer & solution

Answer: (C) The percentage change in input needed to drive the controller output through its full range

PB = 100/Kc for dimensionless gain.

Question 12

What is the proportional band of a controller with gain 2?

  1. 2%
  2. 20%
  3. 50%
  4. 200%
Show answer & solution

Answer: (C) 50%

PB = 100/2.

Question 13

What is reset windup?

  1. Integral action accumulating a large output when the final element is saturated, causing overshoot
  2. Valve sticking
  3. Derivative kick
  4. Sensor failure
Show answer & solution

Answer: (A) Integral action accumulating a large output when the final element is saturated, causing overshoot

Anti-windup logic limits the integral term.

Question 14

What is derivative kick?

  1. A slow response
  2. A spike in controller output caused by a sudden set point change acting on derivative action
  3. A valve leak
  4. A sensor fault
Show answer & solution

Answer: (B) A spike in controller output caused by a sudden set point change acting on derivative action

Derivative on measurement avoids it.

Question 15

What is on–off control?

  1. Continuous PID
  2. Feedforward control
  3. Proportional control
  4. Control in which the final element is either fully open or fully closed
Show answer & solution

Answer: (D) Control in which the final element is either fully open or fully closed

A dead band (differential gap) reduces cycling; home thermostats use it.

Question 16

What is direct action of a controller?

  1. Controller output increases as measured value increases
  2. Output decreases as measured value increases
  3. Output is constant
  4. Output depends only on set point
Show answer & solution

Answer: (A) Controller output increases as measured value increases

Action must match valve type and process gain to give negative feedback.

Question 17

What is the Ziegler–Nichols closed-loop (ultimate gain) method?

  1. Guessing settings
  2. Finding the gain at which the loop oscillates continuously and its period, then calculating settings
  3. Using frequency response with no oscillation
  4. Using a step test in open loop only
Show answer & solution

Answer: (B) Finding the gain at which the loop oscillates continuously and its period, then calculating settings

For a PI controller Kc = 0.45Ku and τI = Pu/1.2.

Question 18

What proportional gain does Ziegler–Nichols recommend for a P-only controller?

  1. Ku
  2. 2 Ku
  3. 0.6 Ku
  4. 0.5 Ku
Show answer & solution

Answer: (D) 0.5 Ku

For PID it is 0.6 Ku.

Question 19

What is the Cohen–Coon method?

  1. A valve sizing method
  2. A tuning method based on first-order-plus-dead-time parameters from an open-loop step test
  3. A closed-loop oscillation method
  4. A frequency method only
Show answer & solution

Answer: (B) A tuning method based on first-order-plus-dead-time parameters from an open-loop step test

It suits processes with significant dead time.

Question 20

Which integral error criterion penalises errors persisting for a long time most heavily?

  1. IAE
  2. Peak error
  3. ITAE (integral of time-weighted absolute error)
  4. ISE
Show answer & solution

Answer: (C) ITAE (integral of time-weighted absolute error)

ISE penalises large errors heavily.

Question 21

What is the effect of increasing proportional gain in a feedback loop?

  1. Faster response and less offset, but more oscillation and eventual instability
  2. No effect
  3. More offset
  4. Slower response
Show answer & solution

Answer: (A) Faster response and less offset, but more oscillation and eventual instability

Excessive gain makes the loop unstable.

Question 22

What is the closed-loop transfer function for set point changes in a simple feedback loop?

  1. Gm/(1 + Gc)
  2. GcGvGp
  3. 1/(1 + GcGvGpGm)
  4. GcGvGp/(1 + GcGvGpGm)
Show answer & solution

Answer: (D) GcGvGp/(1 + GcGvGpGm)

The denominator gives the characteristic equation.

Question 23

What is the characteristic equation of a feedback loop?

  1. Gp = 1
  2. Gc = 0
  3. Open-loop transfer function = 0
  4. 1 + open-loop transfer function = 0
Show answer & solution

Answer: (D) 1 + open-loop transfer function = 0

Its roots determine stability.

Question 24

What is a servo problem in control?

  1. Selecting valves
  2. Rejecting load disturbances
  3. Following changes in set point
  4. Measuring flow
Show answer & solution

Answer: (C) Following changes in set point

A regulator problem deals with disturbances at fixed set point.

Question 25

What does integral time τI represent?

  1. The time for integral action to repeat the proportional action for a constant error
  2. The derivative time
  3. The dead time
  4. The time constant of the process
Show answer & solution

Answer: (A) The time for integral action to repeat the proportional action for a constant error

Some controllers use reset rate = 1/τI in repeats per minute.

Question 26

What is a controller's bumpless transfer?

  1. Sensor calibration
  2. Switching between manual and automatic without a sudden jump in output
  3. Fast valve stroking
  4. Removing integral action
Show answer & solution

Answer: (B) Switching between manual and automatic without a sudden jump in output

Modern controllers track output in manual mode.

Question 27

What is the steady-state error of a type-1 loop (with integral action) to a step change in set point?

  1. Zero
  2. Equal to 1/Kc
  3. Equal to the step size
  4. Infinite
Show answer & solution

Answer: (A) Zero

Integral action gives zero steady-state error to steps.

Question 28

What is a good starting controller type for liquid level in a surge tank where tight control is not needed?

  1. Derivative only
  2. On–off with no dead band
  3. PID with high gain
  4. P or PI with low gain to use the tank capacity (averaging control)
Show answer & solution

Answer: (D) P or PI with low gain to use the tank capacity (averaging control)

Averaging level control smooths outflow.

Question 29

Which controller mode is commonly used for slow temperature loops with large lags?

  1. On–off only
  2. P only
  3. PID
  4. I only
Show answer & solution

Answer: (C) PID

Derivative action helps with large time constants.

Question 30

What is the controllability ratio θ/τ used for?

  1. Measuring flow
  2. Calibrating transmitters
  3. Sizing valves
  4. Judging how difficult a process is to control; larger ratios are harder
Show answer & solution

Answer: (D) Judging how difficult a process is to control; larger ratios are harder

Dead-time-dominant processes have high ratios.

Question 31

What happens if a controller's action is set wrongly (direct instead of reverse)?

  1. Positive feedback drives the process away from set point
  2. The loop becomes faster
  3. Nothing changes
  4. Offset is removed
Show answer & solution

Answer: (A) Positive feedback drives the process away from set point

Action must give negative feedback.

Question 32

What is the reset rate of a controller with integral time 2 min?

  1. 0.5 repeats per minute
  2. 1 repeat per minute
  3. 2 repeats per minute
  4. 4 repeats per minute
Show answer & solution

Answer: (A) 0.5 repeats per minute

Reset rate = 1/τI.

Question 33

What is the PID tuning rule for internal model control (IMC) based on?

  1. Valve size
  2. Trial and error only
  3. A process model and a single closed-loop time constant parameter
  4. Ultimate gain only
Show answer & solution

Answer: (C) A process model and a single closed-loop time constant parameter

It gives robust settings for FOPDT models.

Question 34

What is the role of the measuring element in a feedback loop?

  1. To actuate the valve
  2. To change the process
  3. To set the set point
  4. To measure the controlled variable and send a signal to the controller
Show answer & solution

Answer: (D) To measure the controlled variable and send a signal to the controller

Measurement lags add to loop dynamics.

Practice these 34 questions interactively →