What is the main purpose of comminution in mineral processing?
Show answer & solution
Answer: (C) To reduce ore size and liberate valuable minerals from gangue
Liberation is needed before minerals can be separated.
Mining Engineering · Mine Economics & Mineral Processing
30 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the main purpose of comminution in mineral processing?
Answer: (C) To reduce ore size and liberate valuable minerals from gangue
Liberation is needed before minerals can be separated.
Which crusher is commonly used as a primary crusher for very high tonnages in large mines?
Answer: (C) Gyratory crusher
Gyratory crushers crush continuously and handle high throughput.
Which crusher has a fixed jaw and a moving jaw that crush ore in a V-shaped chamber?
Answer: (A) Jaw crusher
The Blake jaw crusher is the most common type.
What is the reduction ratio of a crusher?
Answer: (D) The ratio of feed size to product size
Primary crushers usually have reduction ratios of about 4 to 8.
What is the reduction ratio for a crusher reducing ore from 600 mm to 150 mm?
Answer: (B) 4
600/150 = 4.
Which mill uses steel balls as grinding media?
Answer: (B) Ball mill
Ball mills are used for fine grinding.
Which mill uses the ore itself as the grinding medium?
Answer: (C) Autogenous (AG) mill
AG mills avoid steel media costs.
What is a semi-autogenous (SAG) mill?
Answer: (A) A mill that grinds with ore plus a small charge of steel balls
SAG mills are widely used in large copper and gold plants.
What is the critical speed of a tumbling mill?
Answer: (D) The speed at which the media just centrifuge against the shell and stop tumbling
Mills normally run at about 65–80% of critical speed.
What is the formula for the critical speed of a mill in rpm, with internal diameter D in metres?
Answer: (A) Nc = 42.3/√D
Larger mills have lower critical speeds.
At about what fraction of critical speed do ball mills normally operate?
Answer: (C) 65% to 80%
Below this, grinding is inefficient; above it, media centrifuge.
Which law is used to calculate grinding energy using the work index?
Answer: (D) Bond's law
W = 10Wi(1/√P80 − 1/√F80).
What is the Bond work index?
Answer: (B) The energy needed to reduce ore from infinite size to 80% passing 100 micrometres, in kWh/t
It is measured in standard laboratory tests.
Which comminution law states that energy is proportional to the new surface area produced, and suits fine grinding?
Answer: (B) Rittinger's law
Rittinger's law fits fine grinding best.
Which comminution law is considered most suitable for coarse crushing?
Answer: (A) Kick's law
Kick's law assumes energy proportional to the reduction ratio.
What is a closed grinding circuit?
Answer: (D) A circuit in which a classifier returns oversize material to the mill
Closed circuits prevent over-grinding and control product size.
What is circulating load in a grinding circuit?
Answer: (C) The ratio of material returned to the mill by the classifier to the new feed
Circulating loads of 200–400% are common in ball mill circuits.
Which device is most commonly used to classify ground slurry by particle size in grinding circuits?
Answer: (B) Hydrocyclone
Coarse particles leave through the underflow and fines through the overflow.
What is the main purpose of screening in mineral processing?
Answer: (D) Separating particles by size using a surface with openings
Vibrating screens are widely used after crushing.
What does P80 mean in comminution?
Answer: (A) The size through which 80% of the product passes
P80 and F80 are used in Bond's law.
What is meant by the mesh number of a sieve?
Answer: (C) The number of openings per linear inch
Higher mesh numbers have smaller openings.
What is a high-pressure grinding roll (HPGR)?
Answer: (C) A machine that crushes ore between two counter-rotating rolls at very high pressure
HPGRs reduce energy consumption and create micro-cracks.
What is the main problem caused by over-grinding of ore?
Answer: (A) Formation of slimes that reduce separation efficiency and waste energy
Very fine particles are difficult to recover by flotation and gravity.
Which stage of mineral processing usually consumes the most energy?
Answer: (B) Comminution (crushing and grinding)
Grinding alone can use about half the plant's energy.
What is liberation size?
Answer: (D) The particle size at which valuable minerals are freed from gangue
Ore must be ground to about the liberation size for separation.
What is the main advantage of a rod mill?
Answer: (A) It produces a uniform product with few fines
Rods grind the coarsest particles preferentially.
What are mill liners used for?
Answer: (C) Protecting the mill shell and lifting the charge for effective grinding
Liners are made of steel or rubber.
What is the typical F80 used in Bond's law?
Answer: (D) The size through which 80% of the feed passes
Comminution energy depends on both F80 and P80.
Which crusher is commonly used as a secondary or tertiary crusher in hard rock plants?
Answer: (B) Cone crusher
Cone crushers produce finer products.
What is the purpose of a grizzly before a primary crusher?
Answer: (A) To bypass fines and protect the crusher from oversize
Grizzlies are heavy bar screens.