Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Manufacturing Processes: Welding

Mechanical Engineering · Manufacturing Processes

37 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is welding?

  1. Joining two pieces of metal by heating them to a suitable temperature, with or without pressure and filler metal
  2. Joining with bolts
  3. Cutting metal
  4. Joining with adhesives only
Show answer & solution

Answer: (A) Joining two pieces of metal by heating them to a suitable temperature, with or without pressure and filler metal

It produces a permanent joint.

Question 2

What is the approximate temperature of an electric welding arc?

  1. About 1000 °C
  2. About 2000 °C
  3. About 6000 °C
  4. About 20,000 °C
Show answer & solution

Answer: (C) About 6000 °C

The core of a plasma arc is much hotter.

Question 3

What is shielded metal arc welding (SMAW)?

  1. Welding under a layer of granular flux
  2. Arc welding with a consumable electrode coated with flux
  3. Welding with gas flame
  4. Welding with a tungsten electrode
Show answer & solution

Answer: (B) Arc welding with a consumable electrode coated with flux

It is also called manual metal arc or stick welding.

Question 4

What are the main functions of electrode coating (flux) in arc welding?

  1. Cooling the weld
  2. Making the electrode heavier
  3. Increasing current only
  4. Stabilising the arc, shielding the molten metal from air and forming slag
Show answer & solution

Answer: (D) Stabilising the arc, shielding the molten metal from air and forming slag

Coatings may also add alloying elements.

Question 5

In DC arc welding, which pole receives about two-thirds of the heat?

  1. The positive pole
  2. The negative pole
  3. Both equally
  4. Neither
Show answer & solution

Answer: (A) The positive pole

This is why polarity affects penetration.

Question 6

What is DC straight polarity (DCSP)?

  1. No polarity
  2. Electrode connected to the negative terminal and work to the positive terminal
  3. Alternating current
  4. Electrode positive and work negative
Show answer & solution

Answer: (B) Electrode connected to the negative terminal and work to the positive terminal

More heat goes to the work, giving deeper penetration.

Question 7

When is DC reverse polarity (DCRP) preferred?

  1. For cutting steel
  2. For brazing
  3. For thick plates needing deep penetration
  4. For welding thin sheets and non-ferrous metals where less heat in the work is needed
Show answer & solution

Answer: (D) For welding thin sheets and non-ferrous metals where less heat in the work is needed

The electrode becomes positive and receives more heat.

Question 8

What is TIG (GTAW) welding?

  1. Resistance welding
  2. Arc welding with a non-consumable tungsten electrode and inert gas shielding
  3. Arc welding with a consumable wire
  4. Gas flame welding
Show answer & solution

Answer: (B) Arc welding with a non-consumable tungsten electrode and inert gas shielding

It gives high-quality welds on aluminium and stainless steel.

Question 9

What is MIG (GMAW) welding?

  1. Welding with a tungsten electrode
  2. Thermit welding
  3. Arc welding with a continuously fed consumable wire electrode and gas shielding
  4. Welding under granular flux
Show answer & solution

Answer: (C) Arc welding with a continuously fed consumable wire electrode and gas shielding

It has a high deposition rate and is easy to automate.

Question 10

Which inert gas is commonly used for shielding in TIG and MIG welding?

  1. Argon
  2. Hydrogen
  3. Nitrogen
  4. Oxygen
Show answer & solution

Answer: (A) Argon

Helium is also used; CO₂ is used for MIG welding of steel.

Question 11

What is submerged arc welding?

  1. Welding with a tungsten electrode
  2. Welding in vacuum
  3. Welding under water
  4. Arc welding in which the arc is covered by a layer of granular flux
Show answer & solution

Answer: (D) Arc welding in which the arc is covered by a layer of granular flux

It is used for thick plates and long straight welds with high deposition.

Question 12

Which welding process is used for joining very thick steel sections in a single pass in the vertical position?

  1. Soldering
  2. TIG welding
  3. Spot welding
  4. Electroslag welding
Show answer & solution

Answer: (D) Electroslag welding

Heat is generated by the resistance of molten slag.

Question 13

What is thermit welding mainly used for?

  1. Welding electronic parts
  2. Welding thin sheets
  3. Joining railway rails and repairing heavy sections
  4. Welding plastics
Show answer & solution

Answer: (C) Joining railway rails and repairing heavy sections

Heat comes from the reaction of aluminium powder with iron oxide.

Question 14

On which principle does resistance welding work?

  1. Heat generated by electrical resistance at the joint (H = I²Rt) with pressure applied
  2. Heat from friction
  3. Heat from a gas flame
  4. Heat from an electric arc
Show answer & solution

Answer: (A) Heat generated by electrical resistance at the joint (H = I²Rt) with pressure applied

No filler metal is needed.

Question 15

What is spot welding used for?

  1. Joining rails
  2. Joining overlapping thin sheets at separate points
  3. Joining thick plates
  4. Joining pipes end to end
Show answer & solution

Answer: (B) Joining overlapping thin sheets at separate points

It is widely used in car body manufacture.

Question 16

What should be the minimum spacing between two adjacent spot welds, in terms of spot diameter d?

  1. About 3d
  2. About 1.5d
  3. About 10d
  4. About d
Show answer & solution

Answer: (A) About 3d

Closer spacing shunts current through the previous weld.

Question 17

Which resistance welding process produces a continuous leak-tight joint using roller electrodes?

  1. Flash butt welding
  2. Projection welding
  3. Spot welding
  4. Seam welding
Show answer & solution

Answer: (D) Seam welding

It is used for fuel tanks and containers.

Question 18

What is projection welding?

  1. Welding with a tungsten electrode
  2. Welding with rollers
  3. Resistance welding in which current is concentrated at small projections pressed on one part
  4. Welding with gas
Show answer & solution

Answer: (C) Resistance welding in which current is concentrated at small projections pressed on one part

Several welds can be made at once.

Question 19

What is the maximum flame temperature of an oxy-acetylene flame?

  1. About 800 °C
  2. About 1500 °C
  3. About 3200 °C
  4. About 6000 °C
Show answer & solution

Answer: (C) About 3200 °C

It is the hottest common fuel-gas flame.

Question 20

How is a neutral flame obtained in oxy-acetylene welding?

  1. By supplying excess acetylene
  2. By supplying approximately equal volumes of oxygen and acetylene
  3. By supplying excess oxygen
  4. By using only oxygen
Show answer & solution

Answer: (B) By supplying approximately equal volumes of oxygen and acetylene

It is used for most metals, including mild steel.

Question 21

For which metals is an oxidising flame used?

  1. Brass and bronze
  2. Mild steel
  3. High-carbon steel
  4. Nickel
Show answer & solution

Answer: (A) Brass and bronze

Excess oxygen helps prevent zinc loss from brass.

Question 22

For which metals is a carburising (reducing) flame used?

  1. Copper
  2. Bronze
  3. Brass
  4. High-carbon steel, nickel and hard-facing alloys
Show answer & solution

Answer: (D) High-carbon steel, nickel and hard-facing alloys

It has excess acetylene.

Question 23

What is gas cutting of steel?

  1. Melting steel with an arc
  2. Heating steel to its ignition temperature and then oxidising it with a jet of pure oxygen
  3. Sawing steel
  4. Grinding steel
Show answer & solution

Answer: (B) Heating steel to its ignition temperature and then oxidising it with a jet of pure oxygen

It works well for ferrous metals but not for stainless steel or aluminium.

Question 24

What is the difference between brazing and soldering?

  1. Brazing uses a filler that melts above 450 °C; soldering uses a filler that melts below 450 °C
  2. Soldering is stronger than brazing
  3. They are the same
  4. Brazing melts the base metal
Show answer & solution

Answer: (A) Brazing uses a filler that melts above 450 °C; soldering uses a filler that melts below 450 °C

In both, the base metal does not melt.

Question 25

What filler is commonly used in soldering electrical joints?

  1. Brass
  2. Tin–lead or lead-free tin alloy
  3. Silver–copper
  4. Steel
Show answer & solution

Answer: (B) Tin–lead or lead-free tin alloy

Rosin flux is used for electronics.

Question 26

What is undercut in welding?

  1. Excess weld metal
  2. Gas porosity
  3. A crack in the weld
  4. A groove melted into the base metal along the edge of the weld and left unfilled
Show answer & solution

Answer: (D) A groove melted into the base metal along the edge of the weld and left unfilled

It is caused by too high current or wrong electrode angle.

Question 27

Which welding process is carried out in a vacuum chamber?

  1. MIG welding
  2. Thermit welding
  3. Electron beam welding
  4. Gas welding
Show answer & solution

Answer: (C) Electron beam welding

It gives deep, narrow welds with little distortion.

Question 28

What is friction welding?

  1. Welding with an electric arc
  2. Welding with adhesives
  3. Joining parts by rotating one against the other under pressure until the interface becomes plastic
  4. Welding with a gas flame
Show answer & solution

Answer: (C) Joining parts by rotating one against the other under pressure until the interface becomes plastic

It is used to join shafts and dissimilar metals.

Question 29

Which non-destructive test is suitable for detecting surface cracks in non-magnetic materials?

  1. Magnetic particle test
  2. Tensile test
  3. Impact test
  4. Dye penetrant test
Show answer & solution

Answer: (D) Dye penetrant test

The dye seeps into cracks and is drawn out by a developer.

Question 30

Which non-destructive test is used to detect internal defects in welds using X-rays or gamma rays?

  1. Radiographic testing
  2. Visual inspection only
  3. Brinell test
  4. Dye penetrant test
Show answer & solution

Answer: (A) Radiographic testing

Ultrasonic testing is another method for internal defects.

Question 31

Which non-destructive test detects surface and near-surface cracks in ferromagnetic materials?

  1. Radiography only
  2. Magnetic particle test
  3. Dye penetrant test only
  4. Impact test
Show answer & solution

Answer: (B) Magnetic particle test

Iron particles gather at leakage fields above cracks.

Question 32

What is the purpose of preheating before welding high-carbon and alloy steels?

  1. To increase hardness
  2. To clean the surface
  3. To increase distortion
  4. To reduce cooling rate and prevent cracking
Show answer & solution

Answer: (D) To reduce cooling rate and prevent cracking

Rapid cooling can form brittle martensite.

Question 33

What is the purpose of tack welding?

  1. Cutting the plates
  2. Testing the weld
  3. Making the final weld
  4. Holding parts in position with small temporary welds before final welding
Show answer & solution

Answer: (D) Holding parts in position with small temporary welds before final welding

It prevents parts moving during welding.

Question 34

What is the leftward (forehand) technique in gas welding suitable for?

  1. Cast iron only
  2. Thin plates, usually up to about 5 mm
  3. Aluminium only
  4. Very thick plates
Show answer & solution

Answer: (B) Thin plates, usually up to about 5 mm

The rightward technique is used for thicker plates.

Question 35

What is flash butt welding?

  1. Arc welding with tungsten
  2. Spot welding of sheets
  3. Resistance welding of rod or pipe ends brought together with flashing and then forged under pressure
  4. Gas welding of pipes
Show answer & solution

Answer: (C) Resistance welding of rod or pipe ends brought together with flashing and then forged under pressure

It is used for joining rails and chains.

Question 36

What is slag inclusion in welds?

  1. Non-metallic slag trapped in the weld metal
  2. A crack across the weld
  3. Gas bubbles in the weld
  4. A groove at the weld edge
Show answer & solution

Answer: (A) Non-metallic slag trapped in the weld metal

It is caused by poor cleaning between passes.

Question 37

What is the purpose of flux in brazing and soldering?

  1. Cooling the joint
  2. Making the joint stronger than the base metal
  3. Supplying heat
  4. Removing oxides and preventing oxidation so the filler can wet the surfaces
Show answer & solution

Answer: (D) Removing oxides and preventing oxidation so the filler can wet the surfaces

Borax is a common brazing flux.

Practice these 37 questions interactively →