Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Manufacturing Processes: Machining

Mechanical Engineering · Manufacturing Processes

47 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is machining?

  1. Joining metals
  2. Pouring metal into moulds
  3. Shaping metal by compressive force only
  4. Removing material from a workpiece in the form of chips to obtain the required shape and size
Show answer & solution

Answer: (D) Removing material from a workpiece in the form of chips to obtain the required shape and size

Turning, drilling and milling are machining processes.

Question 2

How is the size of a lathe usually specified?

  1. By the swing over the bed and the distance between centres
  2. By motor power only
  3. By its weight
  4. By spindle speed only
Show answer & solution

Answer: (A) By the swing over the bed and the distance between centres

Swing is the largest diameter that can be turned.

Question 3

Which part of a lathe carries the cross-slide, compound rest and tool post?

  1. Bed
  2. Headstock
  3. Carriage (saddle)
  4. Tailstock
Show answer & solution

Answer: (C) Carriage (saddle)

The apron on the carriage contains the feed mechanism.

Question 4

Which part of a lathe is used to hold drills or support long work with a dead centre?

  1. Apron
  2. Headstock
  3. Tailstock
  4. Carriage
Show answer & solution

Answer: (C) Tailstock

It can be moved along the bed and locked.

Question 5

What is the cutting speed in turning?

  1. The peripheral speed of the workpiece relative to the tool, V = πDN/1000 m/min
  2. The spindle speed in rpm
  3. The feed per revolution
  4. The depth of cut
Show answer & solution

Answer: (A) The peripheral speed of the workpiece relative to the tool, V = πDN/1000 m/min

D is in mm and N in rpm.

Question 6

What is feed in turning?

  1. The spindle speed
  2. The distance the tool advances along the work for each revolution
  3. The speed of the work surface
  4. The depth of the cut
Show answer & solution

Answer: (B) The distance the tool advances along the work for each revolution

It is measured in mm per revolution.

Question 7

Which methods are used to turn tapers on a lathe?

  1. Using a reamer only
  2. Using a grinding wheel only
  3. Using a drill only
  4. Swivelling the compound rest, offsetting the tailstock and using a taper turning attachment
Show answer & solution

Answer: (D) Swivelling the compound rest, offsetting the tailstock and using a taper turning attachment

Form tools can also produce short tapers.

Question 8

Which lathe mechanism is used for thread cutting?

  1. Lead screw and half nut
  2. Tailstock
  3. Steady rest
  4. Feed rod only
Show answer & solution

Answer: (A) Lead screw and half nut

The lead screw moves the carriage at a fixed ratio to spindle speed.

Question 9

What is knurling?

  1. Making holes
  2. Turning tapers
  3. Producing a diamond or straight pattern on a surface for grip using knurling rolls
  4. Cutting threads
Show answer & solution

Answer: (C) Producing a diamond or straight pattern on a surface for grip using knurling rolls

It is a forming operation, not a cutting operation.

Question 10

What is facing on a lathe?

  1. Making a taper
  2. Reducing the diameter along the length
  3. Cutting threads
  4. Machining the end of a workpiece to produce a flat surface perpendicular to the axis
Show answer & solution

Answer: (D) Machining the end of a workpiece to produce a flat surface perpendicular to the axis

The tool moves across the face of the work.

Question 11

What is the rake angle of a cutting tool?

  1. The angle that prevents rubbing of the flank
  2. The angle of the tool face that guides the chip away from the cutting edge
  3. The angle of the cutting edge to the axis
  4. The nose radius
Show answer & solution

Answer: (B) The angle of the tool face that guides the chip away from the cutting edge

A positive rake angle reduces cutting force.

Question 12

What is the purpose of the relief (clearance) angle on a cutting tool?

  1. To prevent the flank of the tool from rubbing against the work surface
  2. To strengthen the tool point
  3. To improve surface finish only
  4. To guide the chip
Show answer & solution

Answer: (A) To prevent the flank of the tool from rubbing against the work surface

Too large a clearance weakens the cutting edge.

Question 13

Which type of chip is formed when machining ductile materials at high speed with a positive rake angle?

  1. Discontinuous chip
  2. Continuous chip
  3. Serrated chip only
  4. Continuous chip with built-up edge
Show answer & solution

Answer: (B) Continuous chip

It gives a good surface finish.

Question 14

Which type of chip is formed when machining brittle materials such as cast iron?

  1. Continuous chip
  2. Long ribbon chip
  3. Discontinuous chip
  4. Continuous chip with built-up edge
Show answer & solution

Answer: (C) Discontinuous chip

The material fractures into small segments.

Question 15

What causes a built-up edge on a cutting tool?

  1. Using coolant
  2. High cutting speed
  3. Machining brittle materials
  4. Welding of work material onto the tool face at low cutting speed with ductile materials
Show answer & solution

Answer: (D) Welding of work material onto the tool face at low cutting speed with ductile materials

It spoils surface finish and changes tool geometry.

Question 16

What is orthogonal cutting?

  1. Cutting with the edge inclined to the motion
  2. Grinding
  3. Cutting with a multi-point tool only
  4. Cutting in which the cutting edge is perpendicular to the direction of cutting motion
Show answer & solution

Answer: (D) Cutting in which the cutting edge is perpendicular to the direction of cutting motion

Oblique cutting has the edge inclined.

Question 17

What is the Merchant circle used for?

  1. Analysing forces in metal cutting
  2. Measuring tool life
  3. Designing cutting fluids
  4. Measuring surface finish
Show answer & solution

Answer: (A) Analysing forces in metal cutting

It relates cutting, thrust, shear and friction forces.

Question 18

What is Taylor's tool life equation?

  1. V/T = C
  2. VT = n
  3. VTⁿ = C
  4. V = CT
Show answer & solution

Answer: (C) VTⁿ = C

V is cutting speed, T tool life and n, C are constants.

Question 19

What is the typical value of the exponent n in Taylor's equation for HSS tools?

  1. About 0.1–0.15
  2. About 0.5–0.6
  3. About 1.0
  4. About 2.0
Show answer & solution

Answer: (A) About 0.1–0.15

For carbide tools, n is about 0.2–0.25.

Question 20

What is the effect of cutting speed on tool life?

  1. Higher speed increases tool life
  2. Higher cutting speed greatly reduces tool life
  3. Speed has no effect
  4. Speed affects only surface finish
Show answer & solution

Answer: (B) Higher cutting speed greatly reduces tool life

Cutting speed has the strongest effect of all cutting variables.

Question 21

What is crater wear?

  1. Chipping of the edge
  2. Breakage of the tool tip
  3. Wear on the rake face of the tool caused by the sliding chip
  4. Wear on the flank
Show answer & solution

Answer: (C) Wear on the rake face of the tool caused by the sliding chip

It is common with carbide tools at high speed.

Question 22

What is flank wear?

  1. Wear on the rake face
  2. Wear on the clearance face of the tool caused by rubbing against the machined surface
  3. Built-up edge
  4. Tool fracture
Show answer & solution

Answer: (B) Wear on the clearance face of the tool caused by rubbing against the machined surface

Flank wear width is commonly used as a tool life criterion.

Question 23

What is the composition of 18-4-1 high-speed steel?

  1. 18% carbon, 4% vanadium and 1% tungsten
  2. 18% chromium, 4% tungsten and 1% carbon
  3. 18% nickel, 4% cobalt and 1% iron
  4. 18% tungsten, 4% chromium and 1% vanadium
Show answer & solution

Answer: (D) 18% tungsten, 4% chromium and 1% vanadium

HSS retains hardness up to about 600 °C.

Question 24

What are cemented carbide tools mainly made of?

  1. High-speed steel
  2. Diamond
  3. Tungsten carbide grains bonded with cobalt
  4. Aluminium oxide
Show answer & solution

Answer: (C) Tungsten carbide grains bonded with cobalt

They can cut at speeds several times higher than HSS.

Question 25

Why are diamond tools not used for machining steel?

  1. Diamond is too soft
  2. Diamond is too cheap
  3. Steel is too soft
  4. Carbon in diamond diffuses into iron at high temperature, causing rapid wear
Show answer & solution

Answer: (D) Carbon in diamond diffuses into iron at high temperature, causing rapid wear

Cubic boron nitride (CBN) is used for hard steels instead.

Question 26

What is hot hardness of a tool material?

  1. Its hardness after quenching
  2. Its ability to retain hardness at high cutting temperatures
  3. Its hardness at room temperature
  4. Its brittleness
Show answer & solution

Answer: (B) Its ability to retain hardness at high cutting temperatures

It allows higher cutting speeds.

Question 27

What are the main functions of cutting fluids?

  1. Cooling the tool and work, lubricating the cutting zone and washing away chips
  2. Increasing friction
  3. Heating the work
  4. Hardening the tool
Show answer & solution

Answer: (A) Cooling the tool and work, lubricating the cutting zone and washing away chips

Soluble oils are commonly used.

Question 28

What is the standard point angle of a general-purpose twist drill?

  1. 60°
  2. 90°
  3. 118°
  4. 140°
Show answer & solution

Answer: (C) 118°

Harder materials may use larger point angles.

Question 29

What is reaming?

  1. Making a new hole
  2. Cutting internal threads
  3. Enlarging a hole with a single-point tool
  4. Finishing an existing hole to accurate size and smooth surface using a multi-edged tool
Show answer & solution

Answer: (D) Finishing an existing hole to accurate size and smooth surface using a multi-edged tool

Reamers remove only a small amount of material.

Question 30

What is boring?

  1. Enlarging and truing an existing hole with a single-point tool
  2. Cutting internal threads
  3. Making a new hole with a drill
  4. Finishing a hole with a reamer
Show answer & solution

Answer: (A) Enlarging and truing an existing hole with a single-point tool

Boring corrects the position and straightness of holes.

Question 31

What is countersinking?

  1. Finishing a hole
  2. Making a conical enlargement at the end of a hole for a countersunk screw head
  3. Cutting threads
  4. Making a flat-bottomed enlargement
Show answer & solution

Answer: (B) Making a conical enlargement at the end of a hole for a countersunk screw head

Counterboring makes a flat-bottomed enlargement.

Question 32

What is tapping?

  1. Cutting internal threads in a hole using a tap
  2. Enlarging holes
  3. Cutting external threads
  4. Making holes
Show answer & solution

Answer: (A) Cutting internal threads in a hole using a tap

A tap set usually includes taper, second and plug taps.

Question 33

What is the difference between up milling and down milling?

  1. They are the same
  2. Up milling needs a backlash eliminator
  3. Down milling gives a poorer finish
  4. In up milling, the cutter rotates against the feed; in down (climb) milling, it rotates in the direction of feed
Show answer & solution

Answer: (D) In up milling, the cutter rotates against the feed; in down (climb) milling, it rotates in the direction of feed

Down milling needs a backlash eliminator on the table feed screw.

Question 34

What is a dividing (indexing) head used for on a milling machine?

  1. Cooling the work
  2. Measuring speed
  3. Dividing the work into equal angular parts, such as for cutting gear teeth
  4. Holding cutters
Show answer & solution

Answer: (C) Dividing the work into equal angular parts, such as for cutting gear teeth

In simple indexing, crank turns = 40/N.

Question 35

How many turns of the index crank are needed in simple indexing to cut a gear with 20 teeth?

  1. 1
  2. 2
  3. 4
  4. 20
Show answer & solution

Answer: (B) 2

Turns = 40/20 = 2.

Question 36

What is a shaper used for?

  1. Grinding surfaces
  2. Cutting gears only
  3. Machining flat surfaces with a reciprocating single-point tool on small and medium work
  4. Making holes
Show answer & solution

Answer: (C) Machining flat surfaces with a reciprocating single-point tool on small and medium work

It uses a quick return mechanism.

Question 37

What is the main difference between a shaper and a planer?

  1. They are the same
  2. A shaper is for very large work
  3. A planer is for small work
  4. In a shaper, the tool reciprocates; in a planer, the work reciprocates under a stationary tool
Show answer & solution

Answer: (D) In a shaper, the tool reciprocates; in a planer, the work reciprocates under a stationary tool

Planers are used for large heavy workpieces.

Question 38

What is broaching?

  1. Drilling a hole
  2. Machining with a multi-tooth tool whose teeth increase in height, pulled or pushed through or over the work
  3. Grinding with a wheel
  4. Reaming a hole
Show answer & solution

Answer: (B) Machining with a multi-tooth tool whose teeth increase in height, pulled or pushed through or over the work

It is used for keyways and internal splines.

Question 39

Which abrasive is generally used for grinding steel?

  1. Aluminium oxide
  2. Diamond only
  3. Garnet only
  4. Silicon carbide
Show answer & solution

Answer: (A) Aluminium oxide

Silicon carbide is used for cast iron, non-ferrous metals and non-metals.

Question 40

What does the grade of a grinding wheel indicate?

  1. The size of the grains
  2. The spacing of grains
  3. The strength (hardness) of the bond holding the abrasive grains
  4. The type of abrasive
Show answer & solution

Answer: (C) The strength (hardness) of the bond holding the abrasive grains

A hard wheel holds grains longer.

Question 41

Which bond is most commonly used in grinding wheels?

  1. Resinoid bond
  2. Vitrified bond
  3. Shellac bond
  4. Rubber bond
Show answer & solution

Answer: (B) Vitrified bond

It is strong, porous and unaffected by water and oil.

Question 42

What is glazing of a grinding wheel?

  1. A condition in which the abrasive grains become dull and the surface shiny because the wheel is too hard
  2. Breaking of the wheel
  3. Wear of the bond
  4. Clogging of pores with metal
Show answer & solution

Answer: (A) A condition in which the abrasive grains become dull and the surface shiny because the wheel is too hard

Dressing restores the cutting surface.

Question 43

What is dressing of a grinding wheel?

  1. Making the wheel round only
  2. Changing the bond
  3. Balancing the wheel
  4. Removing dull grains and loaded material to expose sharp abrasive
Show answer & solution

Answer: (D) Removing dull grains and loaded material to expose sharp abrasive

Truing makes the wheel run true and concentric.

Question 44

What is honing mainly used for?

  1. Finishing internal cylindrical surfaces such as engine cylinder bores
  2. Cutting gears
  3. Cutting threads
  4. Making holes
Show answer & solution

Answer: (A) Finishing internal cylindrical surfaces such as engine cylinder bores

Abrasive stones rotate and reciprocate in the bore.

Question 45

What is lapping?

  1. Broaching
  2. A fine finishing process using loose abrasive between a lap and the work
  3. Grinding with a wheel
  4. Cutting with a single-point tool
Show answer & solution

Answer: (B) A fine finishing process using loose abrasive between a lap and the work

It gives very flat and smooth surfaces such as gauge blocks.

Question 46

Which gear-cutting process generates teeth by a rotating cutter shaped like a worm?

  1. Form milling
  2. Gear shaping
  3. Broaching
  4. Gear hobbing
Show answer & solution

Answer: (D) Gear hobbing

Hobbing is widely used for spur and helical gears.

Question 47

What is centreless grinding?

  1. Internal grinding
  2. Surface grinding
  3. Grinding cylindrical work supported on a work rest between a grinding wheel and a regulating wheel, without centres
  4. Grinding between centres
Show answer & solution

Answer: (C) Grinding cylindrical work supported on a work rest between a grinding wheel and a regulating wheel, without centres

It is used for mass production of pins and rollers.

Practice these 47 questions interactively →