Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Manufacturing Processes: Casting

Mechanical Engineering · Manufacturing Processes

40 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is casting?

  1. Joining two metals by heat
  2. Removing metal with a cutting tool
  3. Shaping metal by hammering
  4. A process of pouring molten metal into a mould cavity, where it solidifies into the required shape
Show answer & solution

Answer: (D) A process of pouring molten metal into a mould cavity, where it solidifies into the required shape

It is used for complex shapes such as engine blocks.

Question 2

What is a pattern in foundry work?

  1. The core box only
  2. A replica of the casting used to make the mould cavity
  3. The molten metal
  4. The finished casting
Show answer & solution

Answer: (B) A replica of the casting used to make the mould cavity

Patterns are usually made of wood, metal or plastic.

Question 3

Why is shrinkage allowance provided on a pattern?

  1. To make the casting easy to remove
  2. To allow for machining
  3. To compensate for contraction of the metal as it cools and solidifies
  4. To prevent distortion
Show answer & solution

Answer: (C) To compensate for contraction of the metal as it cools and solidifies

The pattern is made slightly larger than the casting.

Question 4

What is the typical shrinkage allowance for grey cast iron patterns?

  1. About 1 mm per metre
  2. About 10 mm per metre
  3. About 50 mm per metre
  4. About 100 mm per metre
Show answer & solution

Answer: (B) About 10 mm per metre

Steel needs a larger allowance, about 20 mm per metre.

Question 5

What is draft allowance?

  1. A slight taper on vertical faces of a pattern to make its removal from the mould easy
  2. Allowance for distortion
  3. Extra metal for machining
  4. Allowance for shrinkage
Show answer & solution

Answer: (A) A slight taper on vertical faces of a pattern to make its removal from the mould easy

Internal surfaces need more draft than external ones.

Question 6

What is machining allowance?

  1. Taper for pattern removal
  2. Negative allowance for rapping
  3. Extra material provided on a casting for surfaces that will be machined later
  4. Allowance for shrinkage
Show answer & solution

Answer: (C) Extra material provided on a casting for surfaces that will be machined later

It depends on the metal, size and casting method.

Question 7

Which pattern allowance is negative, making the pattern slightly smaller?

  1. Draft allowance
  2. Shrinkage allowance
  3. Machining allowance
  4. Shake (rapping) allowance
Show answer & solution

Answer: (D) Shake (rapping) allowance

Rapping the pattern enlarges the mould cavity slightly.

Question 8

What is a split pattern?

  1. A pattern made in two or more parts to allow moulding of complex shapes
  2. A pattern with no draft
  3. A pattern for sweeping
  4. A single-piece pattern
Show answer & solution

Answer: (A) A pattern made in two or more parts to allow moulding of complex shapes

The parts are aligned by dowel pins.

Question 9

What is a match plate pattern used for?

  1. Very large castings
  2. Mass production of small castings, with cope and drag patterns mounted on opposite sides of a plate
  3. Making cores only
  4. Single castings
Show answer & solution

Answer: (B) Mass production of small castings, with cope and drag patterns mounted on opposite sides of a plate

It is used with moulding machines.

Question 10

Which pattern is used for large symmetrical castings such as bells?

  1. Match plate pattern
  2. Gated pattern
  3. Sweep pattern
  4. Loose piece pattern
Show answer & solution

Answer: (C) Sweep pattern

A template is rotated about a spindle to shape the mould.

Question 11

What are the main constituents of green moulding sand?

  1. Silica sand, clay (binder) and water
  2. Graphite and resin only
  3. Silica sand and oil only
  4. Cement and sand
Show answer & solution

Answer: (A) Silica sand, clay (binder) and water

Bentonite is a common clay binder.

Question 12

What is permeability of moulding sand?

  1. Its strength when wet
  2. Its resistance to high temperature
  3. Its ability to break up after casting
  4. The property that allows gases and steam to escape through the mould
Show answer & solution

Answer: (D) The property that allows gases and steam to escape through the mould

Low permeability causes blowholes.

Question 13

What is refractoriness of moulding sand?

  1. Its ability to withstand high temperatures without fusing
  2. Its flowability
  3. Its strength when dry
  4. Its ability to let gases escape
Show answer & solution

Answer: (A) Its ability to withstand high temperatures without fusing

Silica sand has high refractoriness.

Question 14

What is collapsibility of moulding sand?

  1. Its strength when green
  2. Its ability to break down easily after the casting solidifies
  3. Its refractoriness
  4. Its permeability
Show answer & solution

Answer: (B) Its ability to break down easily after the casting solidifies

Good collapsibility prevents hot tears.

Question 15

What is a core in casting?

  1. The pattern itself
  2. The riser
  3. The outer mould box
  4. A sand body placed in the mould to form holes or internal cavities in the casting
Show answer & solution

Answer: (D) A sand body placed in the mould to form holes or internal cavities in the casting

Cores are usually baked to make them strong.

Question 16

What are chaplets used for?

  1. Venting gases
  2. Feeding molten metal
  3. Supporting cores inside the mould cavity
  4. Cooling the casting
Show answer & solution

Answer: (C) Supporting cores inside the mould cavity

They fuse into the casting.

Question 17

What are core prints?

  1. Holes for venting
  2. Feeding channels
  3. Markings on the pattern
  4. Projections on a pattern that form seats in the mould to locate and support the core
Show answer & solution

Answer: (D) Projections on a pattern that form seats in the mould to locate and support the core

They make the core sit in the right position.

Question 18

What is the function of a riser (feeder)?

  1. To hold the core
  2. To supply molten metal to the casting as it shrinks during solidification
  3. To pour metal into the mould
  4. To cool the casting quickly
Show answer & solution

Answer: (B) To supply molten metal to the casting as it shrinks during solidification

The riser must solidify after the casting.

Question 19

What is a sprue?

  1. The vertical channel through which molten metal flows from the pouring basin into the mould
  2. The horizontal channel feeding the gates
  3. The reservoir that feeds shrinkage
  4. The core support
Show answer & solution

Answer: (A) The vertical channel through which molten metal flows from the pouring basin into the mould

It is usually tapered to prevent air aspiration.

Question 20

What does Chvorinov's rule state?

  1. Solidification time is proportional to surface area only
  2. Solidification time is independent of shape
  3. Solidification time is proportional to the square of the volume-to-surface-area ratio of the casting
  4. Solidification time is proportional to temperature
Show answer & solution

Answer: (C) Solidification time is proportional to the square of the volume-to-surface-area ratio of the casting

t = k(V/A)²; risers are designed to solidify last.

Question 21

What causes blowholes in castings?

  1. Excessive shake allowance
  2. Low pouring temperature
  3. Trapped gases due to low permeability, excess moisture or poor venting
  4. Too much draft
Show answer & solution

Answer: (C) Trapped gases due to low permeability, excess moisture or poor venting

They appear as smooth round cavities.

Question 22

What is a cold shut defect?

  1. An imperfect fusion where two streams of metal meet but do not fuse properly
  2. A crack due to hot tearing
  3. An extra fin of metal
  4. A gas cavity
Show answer & solution

Answer: (A) An imperfect fusion where two streams of metal meet but do not fuse properly

It is caused by low pouring temperature or slow pouring.

Question 23

What is a misrun defect?

  1. A gas hole
  2. Failure of the metal to fill the mould completely
  3. A crack
  4. A shift of mould halves
Show answer & solution

Answer: (B) Failure of the metal to fill the mould completely

It is caused by low fluidity or low pouring temperature.

Question 24

What is a hot tear in a casting?

  1. Extra metal at the parting line
  2. A gas cavity
  3. An incomplete filling
  4. A crack formed during solidification because contraction is restrained
Show answer & solution

Answer: (D) A crack formed during solidification because contraction is restrained

Good collapsibility of sand reduces hot tears.

Question 25

What is a shrinkage cavity?

  1. A void formed in thick sections because liquid metal was not fed during solidification
  2. A gas bubble near the surface
  3. Sand sticking to the casting
  4. A misrun
Show answer & solution

Answer: (A) A void formed in thick sections because liquid metal was not fed during solidification

Proper risers prevent shrinkage cavities.

Question 26

What is die casting?

  1. Pouring metal into sand moulds
  2. Casting using wax patterns
  3. A process in which molten metal is forced under pressure into a permanent metal die
  4. Spinning a mould to cast pipes
Show answer & solution

Answer: (C) A process in which molten metal is forced under pressure into a permanent metal die

It gives good finish and accuracy.

Question 27

Which metals are commonly die cast?

  1. Titanium only
  2. Low-melting non-ferrous alloys such as zinc, aluminium and magnesium
  3. Steel and cast iron
  4. Tungsten
Show answer & solution

Answer: (B) Low-melting non-ferrous alloys such as zinc, aluminium and magnesium

High temperatures would damage steel dies.

Question 28

What is the difference between hot-chamber and cold-chamber die casting?

  1. They are the same
  2. Hot-chamber is used for aluminium
  3. Cold-chamber needs no die
  4. In hot-chamber die casting, the injection mechanism is immersed in molten metal (for zinc); in cold-chamber, metal is ladled in separately (for aluminium)
Show answer & solution

Answer: (D) In hot-chamber die casting, the injection mechanism is immersed in molten metal (for zinc); in cold-chamber, metal is ladled in separately (for aluminium)

Aluminium would attack the immersed parts in a hot chamber.

Question 29

What is investment casting?

  1. A precision casting process using wax patterns coated with refractory material, which are melted out before pouring
  2. Sand casting with wooden patterns
  3. Pressure die casting
  4. Casting pipes by rotation
Show answer & solution

Answer: (A) A precision casting process using wax patterns coated with refractory material, which are melted out before pouring

It is also called the lost wax process.

Question 30

Which casting process is used to make pipes without using a core?

  1. Shell moulding
  2. Investment casting
  3. Die casting
  4. Centrifugal casting
Show answer & solution

Answer: (D) Centrifugal casting

The rotating mould throws metal against its walls.

Question 31

What is shell moulding?

  1. Casting with wax patterns
  2. A process using a thin shell of resin-bonded sand formed on a heated metal pattern
  3. Casting in permanent metal moulds
  4. Casting in green sand
Show answer & solution

Answer: (B) A process using a thin shell of resin-bonded sand formed on a heated metal pattern

It gives good surface finish and accuracy.

Question 32

What is continuous casting?

  1. Casting in sand moulds
  2. Casting by centrifugal force
  3. Casting molten steel continuously into a water-cooled mould to produce billets, blooms or slabs
  4. Casting one piece at a time
Show answer & solution

Answer: (C) Casting molten steel continuously into a water-cooled mould to produce billets, blooms or slabs

It has largely replaced ingot casting in steel plants.

Question 33

Which furnace is traditionally used to melt cast iron in foundries?

  1. Electric arc furnace only
  2. Blast furnace
  3. Cupola furnace
  4. Crucible furnace for aluminium
Show answer & solution

Answer: (C) Cupola furnace

It uses coke as fuel and limestone as flux.

Question 34

Why is limestone added in a cupola?

  1. It acts as a flux, removing impurities as slag
  2. It increases carbon
  3. It cools the metal
  4. It is a fuel
Show answer & solution

Answer: (A) It acts as a flux, removing impurities as slag

The slag floats on the molten iron.

Question 35

What is a gated pattern?

  1. A pattern with loose pieces
  2. A group of patterns joined by gating channels for producing several small castings at once
  3. A one-piece pattern
  4. A sweep pattern
Show answer & solution

Answer: (B) A group of patterns joined by gating channels for producing several small castings at once

It speeds up moulding of small parts.

Question 36

What is the parting line in a mould?

  1. The top of the riser
  2. The bottom of the sprue
  3. The centre of the core
  4. The line where the cope and drag halves of the mould meet
Show answer & solution

Answer: (D) The line where the cope and drag halves of the mould meet

Fins may form along it.

Question 37

What are the upper and lower parts of a two-part moulding box called?

  1. Core and riser
  2. Sprue and runner
  3. Cope (upper) and drag (lower)
  4. Gate and vent
Show answer & solution

Answer: (C) Cope (upper) and drag (lower)

A middle part, if used, is called a cheek.

Question 38

What is fluidity of molten metal?

  1. Its hardness
  2. Its density
  3. Its ability to flow and fill thin sections of a mould before solidifying
  4. Its viscosity at room temperature
Show answer & solution

Answer: (C) Its ability to flow and fill thin sections of a mould before solidifying

Higher pouring temperature increases fluidity.

Question 39

What is a permanent mould casting process?

  1. Casting in reusable metal moulds without high pressure
  2. Casting with wax patterns
  3. Casting by explosion
  4. Casting in sand moulds
Show answer & solution

Answer: (A) Casting in reusable metal moulds without high pressure

It gives better finish than sand casting.

Question 40

What is the function of vent holes in a mould?

  1. Supporting cores
  2. Feeding metal
  3. Allowing gases and steam to escape from the mould
  4. Cooling the casting
Show answer & solution

Answer: (C) Allowing gases and steam to escape from the mould

They are made with a vent wire.

Practice these 40 questions interactively →