Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Manufacturing Processes: Metal Forming

Mechanical Engineering · Manufacturing Processes

38 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is hot working of metals?

  1. Deformation below the recrystallisation temperature
  2. Plastic deformation carried out above the recrystallisation temperature
  3. Casting at high temperature
  4. Machining at high temperature
Show answer & solution

Answer: (B) Plastic deformation carried out above the recrystallisation temperature

Hot working requires lower forces and refines grain structure.

Question 2

What is cold working of metals?

  1. Plastic deformation carried out below the recrystallisation temperature
  2. Casting at low temperature
  3. Deformation above the recrystallisation temperature
  4. Welding at room temperature
Show answer & solution

Answer: (A) Plastic deformation carried out below the recrystallisation temperature

It increases strength and hardness by strain hardening.

Question 3

What are the advantages of cold working over hot working?

  1. Greater ductility
  2. Lower forces required
  3. Better surface finish, closer tolerances and higher strength
  4. No strain hardening
Show answer & solution

Answer: (C) Better surface finish, closer tolerances and higher strength

However, it needs more force and reduces ductility.

Question 4

What is forging?

  1. Removing metal by cutting
  2. Joining metals with heat
  3. Pouring molten metal into moulds
  4. Shaping metal by compressive forces using hammers or presses, usually when hot
Show answer & solution

Answer: (D) Shaping metal by compressive forces using hammers or presses, usually when hot

Forged parts have good grain flow and strength.

Question 5

Why are forged parts often stronger than cast or machined parts?

  1. Forging makes metal brittle
  2. Forging adds alloying elements
  3. Forging produces a continuous grain flow that follows the shape of the part
  4. Forging removes all impurities
Show answer & solution

Answer: (C) Forging produces a continuous grain flow that follows the shape of the part

Crankshafts and connecting rods are usually forged.

Question 6

What is drop forging?

  1. Rolling between rolls
  2. Closed-die forging in which a heavy hammer falls on the hot metal placed in die impressions
  3. Pressing through a die opening
  4. Open-die forging by hand
Show answer & solution

Answer: (B) Closed-die forging in which a heavy hammer falls on the hot metal placed in die impressions

It is used for spanners and connecting rods.

Question 7

What is upset forging?

  1. Increasing the cross-section of a bar by compressing it along its length
  2. Reducing the cross-section
  3. Drawing out the bar
  4. Bending the bar
Show answer & solution

Answer: (A) Increasing the cross-section of a bar by compressing it along its length

It is used to form bolt heads.

Question 8

What is fullering in forging?

  1. Bending a bar
  2. Making holes
  3. Reducing the cross-section of a bar and lengthening it using a fuller with a rounded edge
  4. Increasing the diameter
Show answer & solution

Answer: (C) Reducing the cross-section of a bar and lengthening it using a fuller with a rounded edge

It is often used before drawing out.

Question 9

What is swaging?

  1. Joining two bars
  2. Reducing the diameter of a bar or tube by hammering it with dies
  3. Cutting a bar
  4. Increasing the diameter
Show answer & solution

Answer: (B) Reducing the diameter of a bar or tube by hammering it with dies

Rotary swaging is used for tubes and rods.

Question 10

What is rolling?

  1. Reducing the thickness of metal by passing it between rotating rolls
  2. Pulling metal through a die
  3. Pressing metal through a die opening
  4. Hammering metal
Show answer & solution

Answer: (A) Reducing the thickness of metal by passing it between rotating rolls

Most steel products are rolled.

Question 11

What is the difference between a bloom, a billet and a slab?

  1. They are the same
  2. A slab is round
  3. A billet is the largest
  4. A bloom has a large square section, a billet a smaller square section, and a slab a wide rectangular section
Show answer & solution

Answer: (D) A bloom has a large square section, a billet a smaller square section, and a slab a wide rectangular section

Slabs are rolled into plates and sheets.

Question 12

Why are rolled threads stronger than cut threads?

  1. Rolled threads are deeper
  2. Rolling produces a continuous grain flow and compressive surface stresses
  3. Rolled threads use stronger material
  4. Cut threads have no grain
Show answer & solution

Answer: (B) Rolling produces a continuous grain flow and compressive surface stresses

Thread rolling is fast and wastes no material.

Question 13

What is extrusion?

  1. Pulling metal through a die
  2. Hammering metal
  3. Rolling metal between rolls
  4. Forcing metal through a die opening to produce long products of constant cross-section
Show answer & solution

Answer: (D) Forcing metal through a die opening to produce long products of constant cross-section

Aluminium window frames are extruded.

Question 14

What is the difference between direct and indirect extrusion?

  1. In direct extrusion, metal flows in the same direction as the ram; in indirect extrusion, it flows opposite to the ram
  2. Direct extrusion has no friction
  3. They are the same
  4. Indirect extrusion needs more force
Show answer & solution

Answer: (A) In direct extrusion, metal flows in the same direction as the ram; in indirect extrusion, it flows opposite to the ram

Indirect extrusion has less friction between billet and container.

Question 15

Which process is used to make collapsible tubes such as toothpaste tubes?

  1. Hot rolling
  2. Sand casting
  3. Impact extrusion
  4. Spot welding
Show answer & solution

Answer: (C) Impact extrusion

A punch strikes a slug of soft metal in a die.

Question 16

What is wire drawing?

  1. Pushing metal through a die
  2. Casting wire
  3. Rolling wire flat
  4. Pulling a rod through a series of dies to reduce its diameter
Show answer & solution

Answer: (D) Pulling a rod through a series of dies to reduce its diameter

The pulling force must not exceed the strength of the drawn wire.

Question 17

Why is annealing often needed between stages in multi-stage (tandem) wire or tube drawing?

  1. Cold drawing hardens the metal, which must be softened to allow further reduction
  2. To improve colour
  3. To join wires
  4. To make the wire thicker
Show answer & solution

Answer: (A) Cold drawing hardens the metal, which must be softened to allow further reduction

Annealing restores ductility.

Question 18

What is deep drawing?

  1. Rolling sheets
  2. Cutting holes in sheets
  3. Forming a cup or shell from a flat sheet by pressing it into a die with a punch
  4. Bending sheets along a line
Show answer & solution

Answer: (C) Forming a cup or shell from a flat sheet by pressing it into a die with a punch

Kitchen sinks and cans are deep drawn.

Question 19

What is spinning in sheet metal work?

  1. Rolling sheet metal
  2. Forming a rotating sheet over a shaped mandrel using a tool
  3. Welding sheet metal
  4. Cutting sheet metal
Show answer & solution

Answer: (B) Forming a rotating sheet over a shaped mandrel using a tool

It is used for lamp reflectors and cooking pots.

Question 20

What is blanking?

  1. Making a hole where the removed piece is scrap
  2. Bending sheet metal
  3. Drawing a cup
  4. Cutting a flat piece (blank) from sheet metal, where the removed piece is the useful part
Show answer & solution

Answer: (D) Cutting a flat piece (blank) from sheet metal, where the removed piece is the useful part

The remaining sheet is scrap.

Question 21

What is punching (piercing)?

  1. Bending sheet metal
  2. Cutting a hole in sheet metal, where the removed slug is scrap
  3. Flattening sheet metal
  4. Cutting a blank that is the useful part
Show answer & solution

Answer: (B) Cutting a hole in sheet metal, where the removed slug is scrap

The sheet with the hole is the product.

Question 22

In blanking, on which tool is the clearance provided?

  1. No clearance is needed
  2. On the die
  3. On the punch (the die is made to the blank size)
  4. On both equally
Show answer & solution

Answer: (C) On the punch (the die is made to the blank size)

In punching, clearance is given on the die and the punch is made to hole size.

Question 23

What is lancing?

  1. Cutting a sheet partly along its length and bending the cut portion
  2. Flattening a curved sheet
  3. Cutting along a straight line fully
  4. Removing metal from the edge
Show answer & solution

Answer: (A) Cutting a sheet partly along its length and bending the cut portion

It is used to make tabs and louvres.

Question 24

What is notching?

  1. Flattening a sheet
  2. Bending a sheet
  3. Removing metal from the edge of a sheet or strip
  4. Cutting a hole in the centre
Show answer & solution

Answer: (C) Removing metal from the edge of a sheet or strip

It is often done before bending.

Question 25

What is coining?

  1. A closed-die squeezing operation that produces fine surface detail on both sides, as in making coins
  2. Cutting a blank
  3. Bending a sheet
  4. Drawing a cup
Show answer & solution

Answer: (A) A closed-die squeezing operation that produces fine surface detail on both sides, as in making coins

Metal flows to fill all parts of the die.

Question 26

What is embossing?

  1. Coining with thickness change
  2. Spinning
  3. Cutting holes
  4. Forming raised or sunken designs on sheet metal with matching dies, without much change in thickness
Show answer & solution

Answer: (D) Forming raised or sunken designs on sheet metal with matching dies, without much change in thickness

Number plates are often embossed.

Question 27

What is planishing?

  1. Drawing wire
  2. Smoothing and straightening sheet metal by light hammering
  3. Cutting sheet metal
  4. Punching holes
Show answer & solution

Answer: (B) Smoothing and straightening sheet metal by light hammering

It removes dents and curves.

Question 28

What is spring-back in bending?

  1. Cracking of the bend
  2. The partial recovery of shape after the bending load is removed due to elastic recovery
  3. Wrinkling of the sheet
  4. Thinning of the sheet
Show answer & solution

Answer: (B) The partial recovery of shape after the bending load is removed due to elastic recovery

It is compensated by over-bending.

Question 29

What is a progressive die?

  1. A die that performs several operations at different stations in successive press strokes as the strip advances
  2. A simple single-operation die
  3. A die performing both cutting and forming at one station
  4. A die performing several cutting operations at one station in one stroke
Show answer & solution

Answer: (A) A die that performs several operations at different stations in successive press strokes as the strip advances

It is used for high-volume production.

Question 30

What is a compound die?

  1. A die for forging only
  2. A die with several stations
  3. A die combining cutting and forming
  4. A die that performs two or more cutting operations at one station in a single stroke
Show answer & solution

Answer: (D) A die that performs two or more cutting operations at one station in a single stroke

Blanking and piercing a washer together is an example.

Question 31

What is a combination die?

  1. A die for cutting only
  2. A die with several stations
  3. A die that performs both cutting and non-cutting (forming) operations at one station in every stroke
  4. A die for forging only
Show answer & solution

Answer: (C) A die that performs both cutting and non-cutting (forming) operations at one station in every stroke

Blanking and drawing a cup together is an example.

Question 32

What is the force required for blanking or punching sheet metal?

  1. Area × yield stress
  2. Perimeter of the cut × sheet thickness × shear strength of the material
  3. Thickness × hardness
  4. Length × elastic modulus
Show answer & solution

Answer: (B) Perimeter of the cut × sheet thickness × shear strength of the material

Shear on the punch reduces the peak force.

Question 33

What is the recrystallisation temperature of a metal roughly equal to?

  1. Twice its melting temperature
  2. About 0.4 times its absolute melting temperature
  3. Room temperature for all metals
  4. Its melting temperature
Show answer & solution

Answer: (B) About 0.4 times its absolute melting temperature

Lead recrystallises near room temperature.

Question 34

What is open-die forging?

  1. Rolling between grooved rolls
  2. Pressing through a die
  3. Forging in which the work is compressed between flat or simple dies that do not enclose it
  4. Forging in closed impressions
Show answer & solution

Answer: (C) Forging in which the work is compressed between flat or simple dies that do not enclose it

It is used for large shafts and simple shapes.

Question 35

What is ring rolling used for?

  1. Making seamless rings such as bearing races and gear blanks
  2. Rolling rails
  3. Rolling sheets
  4. Drawing wire
Show answer & solution

Answer: (A) Making seamless rings such as bearing races and gear blanks

A pierced blank is rolled between two rolls.

Question 36

What is the purpose of a blank holder in deep drawing?

  1. To cut the blank
  2. To prevent wrinkling of the flange during drawing
  3. To lubricate the die
  4. To hold the punch
Show answer & solution

Answer: (B) To prevent wrinkling of the flange during drawing

Too much holding force can tear the cup.

Question 37

What is a shearing operation in sheet metal work?

  1. Cutting sheet metal along a straight line
  2. Flattening a curve
  3. Drawing a cup
  4. Bending sheet metal
Show answer & solution

Answer: (A) Cutting sheet metal along a straight line

Guillotine shears are used for this.

Question 38

What is hot extrusion commonly used to produce?

  1. Sheet steel
  2. Coins
  3. Castings
  4. Aluminium sections, tubes and rods
Show answer & solution

Answer: (D) Aluminium sections, tubes and rods

Complex sections can be produced in one pass.

Practice these 38 questions interactively →