What is heat treatment?
Show answer & solution
Answer: (A) Controlled heating and cooling of metals in the solid state to change their structure and properties
It can soften, harden or relieve stresses.
Mechanical Engineering · Engineering Materials
38 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is heat treatment?
Answer: (A) Controlled heating and cooling of metals in the solid state to change their structure and properties
It can soften, harden or relieve stresses.
What is full annealing of steel?
Answer: (C) Heating above the upper critical temperature, holding and then cooling slowly in the furnace
It softens steel, refines grain and relieves stresses.
What is the main purpose of annealing?
Answer: (D) To soften the metal, improve machinability and ductility and relieve internal stresses
Annealing does not harden steel.
What is normalising?
Answer: (B) Heating steel above the upper critical temperature and cooling it in still air
It gives a finer, more uniform structure than annealing.
How do normalised steels compare with annealed steels?
Answer: (A) They are slightly harder and stronger because air cooling gives finer pearlite
Normalising also relieves stresses rather than inducing them.
What is hardening of steel?
Answer: (B) Heating steel above its critical temperature and quenching it rapidly to form martensite
Rapid cooling prevents formation of pearlite.
What is martensite?
Answer: (D) A hard, brittle, supersaturated solution of carbon in iron with a body-centred tetragonal structure
It is the hardest constituent of quenched steel.
What is the approximate hardness of fully hardened high-carbon martensite?
Answer: (C) About 65 HRC
It is too brittle to use without tempering.
Which quenching medium gives the fastest cooling rate?
Answer: (A) Brine (salt water)
Fast quenching increases the risk of cracking.
What is tempering?
Answer: (D) Reheating hardened steel to a temperature below the lower critical temperature to reduce brittleness and relieve stresses
Higher tempering temperatures give more toughness and less hardness.
What is the critical cooling rate?
Answer: (A) The slowest cooling rate that produces a fully martensitic structure
Alloying elements reduce the critical cooling rate.
What is hardenability?
Answer: (B) The ability of a steel to be hardened to depth by quenching
It depends mainly on alloying elements, not carbon content alone.
Which test is used to measure hardenability of steel?
Answer: (C) Jominy end-quench test
One end of a heated bar is sprayed with water, and hardness is measured along its length.
What does a TTT (time–temperature–transformation) diagram show?
Answer: (C) The transformation of austenite with time at constant temperatures
It is also called an isothermal transformation or S-curve diagram.
What is austempering?
Answer: (A) Quenching steel into a bath held above the martensite start temperature and holding it until bainite forms
It gives toughness with less distortion.
What is martempering (marquenching)?
Answer: (D) Quenching into a bath just above the martensite start temperature, equalising, then cooling slowly through the martensite range
It reduces distortion and cracking.
What is bainite?
Answer: (B) A fine mixture of ferrite and cementite formed by transformation of austenite at temperatures between pearlite and martensite formation
It is tougher than martensite of similar hardness.
What is spheroidising?
Answer: (C) Prolonged heating just below the lower critical temperature to turn cementite into small spheres
It improves the machinability of high-carbon steels.
What is stress relieving?
Answer: (B) Heating to a moderate temperature below the critical range to reduce residual stresses without changing structure much
It is commonly done after welding and machining.
What is retained austenite?
Answer: (D) Austenite that does not transform to martensite on quenching
Sub-zero treatment converts it to martensite.
What is case hardening?
Answer: (A) Producing a hard, wear-resistant surface while keeping a tough core
Electroplating is not a case hardening process.
What is carburising?
Answer: (A) Adding carbon to the surface of low-carbon steel at high temperature, followed by hardening
The case reaches about 0.8–1% carbon.
At what temperature is carburising usually carried out?
Answer: (C) About 900–950 °C
Steel must be austenitic to absorb carbon.
What is nitriding?
Answer: (D) Heating special alloy steels in ammonia gas at about 500–550 °C to form hard nitrides on the surface
No quenching is needed after nitriding.
What surface hardness can nitriding produce?
Answer: (D) About 1000–1100 HV
Nitriding steels contain aluminium, chromium or molybdenum.
What is cyaniding?
Answer: (B) Case hardening by heating steel in a molten cyanide salt bath to add carbon and nitrogen
It produces a thin, hard case quickly.
What is carbonitriding?
Answer: (A) Gas case hardening that adds both carbon and nitrogen to the surface
It is like cyaniding but uses gases.
What is induction hardening?
Answer: (B) Rapid surface heating by high-frequency electric currents followed by quenching
It is used for gear teeth, crankshafts and shafts of medium-carbon steel.
What is flame hardening?
Answer: (C) Heating the surface with an oxy-acetylene flame and quenching immediately
It does not change the surface composition.
What is age (precipitation) hardening?
Answer: (B) Strengthening by forming fine precipitates from a supersaturated solid solution after solution treatment and quenching
Duralumin is the classic example.
What does the addition of copper to aluminium make possible?
Answer: (D) One of the best-known age (precipitation) hardening systems
Duralumin contains about 4% copper.
What is the effect of tempering on hardened steel?
Answer: (B) It reduces hardness and brittleness and increases toughness
Tempering does not improve machinability.
Which is not a purpose of annealing?
Answer: (D) Slightly hardening the steel
Annealing makes steel softer, not harder.
What is the main difference between hardening and case hardening?
Answer: (A) Hardening hardens the whole section, while case hardening hardens only the surface layer
Case-hardened parts have a hard surface and tough core.
What heat treatment is applied to cold-worked metals to relieve stresses and restore ductility?
Answer: (B) Annealing (process annealing)
It allows further cold working.
What is the result of austempering?
Answer: (D) A bainitic structure
It avoids the brittleness of martensite.
Why is preheating essential when welding cast iron?
Answer: (A) To reduce thermal stresses and prevent cracking of the brittle casting
Slow cooling after welding is also important.
What is the effect of annealing white cast iron?
Answer: (C) It produces malleable cast iron
Graphite forms as nodular temper carbon.