Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Measurements & Instrumentation: Power and Energy Measurement

Electrical Engineering · Measurements & Instrumentation

30 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

How are the coils of an electrodynamometer wattmeter connected?

  1. The current coil in series with the load and the pressure coil in parallel with it
  2. Both in series
  3. The current coil in parallel
  4. Both in parallel
Show answer & solution

Answer: (A) The current coil in series with the load and the pressure coil in parallel with it

The deflection is proportional to VI cos φ.

Question 2

Why are low power factor wattmeters used?

  1. To measure DC only
  2. To measure frequency
  3. To measure insulation
  4. To measure power accurately in circuits with low power factor, such as transformer open-circuit tests
Show answer & solution

Answer: (D) To measure power accurately in circuits with low power factor, such as transformer open-circuit tests

Ordinary wattmeters give small, inaccurate deflections at low power factor.

Question 3

Which type of energy meter was traditionally used for household AC supply?

  1. Thermocouple meter
  2. Electrostatic meter
  3. Induction type energy meter with a rotating aluminium disc
  4. PMMC meter
Show answer & solution

Answer: (C) Induction type energy meter with a rotating aluminium disc

Digital static meters have largely replaced them.

Question 4

What is the function of the braking magnet in an induction energy meter?

  1. To measure voltage
  2. To produce a braking torque proportional to disc speed so that speed is proportional to power
  3. To drive the disc
  4. To increase creep
Show answer & solution

Answer: (B) To produce a braking torque proportional to disc speed so that speed is proportional to power

The total revolutions represent energy.

Question 5

What is creep in an induction energy meter?

  1. Slow continuous rotation of the disc when no load is connected
  2. Fast rotation at full load
  3. Stopping of the disc at full load
  4. Reverse rotation on load
Show answer & solution

Answer: (A) Slow continuous rotation of the disc when no load is connected

Holes drilled in the disc help prevent creep.

Question 6

How many revolutions will an energy meter with a constant of 600 rev/kWh make for a 1 kW load in one hour?

  1. 60
  2. 600
  3. 1,000
  4. 6,000
Show answer & solution

Answer: (B) 600

Energy = 1 kWh; revolutions = 600 × 1.

Question 7

What is the meter constant of an energy meter?

  1. The rated voltage
  2. The current rating
  3. The number of phases
  4. The number of revolutions or pulses per kWh
Show answer & solution

Answer: (D) The number of revolutions or pulses per kWh

Electronic meters give pulses per kWh on an LED.

Question 8

What is a maximum demand indicator?

  1. A device that records the highest average power demand over set intervals
  2. A voltage recorder
  3. A meter that records total energy only
  4. A frequency meter
Show answer & solution

Answer: (A) A device that records the highest average power demand over set intervals

Large consumers are charged for maximum demand.

Question 9

What do time-of-use (TOU) meters used by DISCOs record?

  1. Only voltage
  2. Only total energy
  3. Energy consumed separately during peak and off-peak hours
  4. Only frequency
Show answer & solution

Answer: (C) Energy consumed separately during peak and off-peak hours

Peak-hour tariffs are higher in Pakistan.

Question 10

What type of meter is installed for consumers with net metering of rooftop solar?

  1. A prepaid meter only
  2. A water meter
  3. A one-way induction meter
  4. A bidirectional meter that records both import and export
Show answer & solution

Answer: (D) A bidirectional meter that records both import and export

Net billing uses the difference between import and export.

Question 11

What is a tri-vector meter?

  1. A clamp meter
  2. A voltmeter
  3. A meter that records active, reactive and apparent energy (kWh, kVARh and kVAh)
  4. A frequency meter
Show answer & solution

Answer: (C) A meter that records active, reactive and apparent energy (kWh, kVARh and kVAh)

It is used for industrial consumers.

Question 12

Which instrument is commonly used to measure power system frequency in older panels?

  1. Wheatstone bridge
  2. Vibrating reed frequency meter
  3. Energy meter
  4. Megger
Show answer & solution

Answer: (B) Vibrating reed frequency meter

The reed resonating with the supply frequency vibrates most.

Question 13

What is a smart meter?

  1. An electronic meter that records consumption and communicates data remotely
  2. A mechanical meter
  3. A current transformer
  4. A water meter
Show answer & solution

Answer: (A) An electronic meter that records consumption and communicates data remotely

DISCOs use AMI smart meters to reduce losses and improve billing.

Question 14

What are ratio error and phase angle error in current transformers?

  1. Errors in voltage only
  2. Errors in frequency
  3. Differences between actual and nominal ratio, and the phase displacement between primary and reversed secondary current
  4. Errors in resistance only
Show answer & solution

Answer: (C) Differences between actual and nominal ratio, and the phase displacement between primary and reversed secondary current

Metering CTs must keep these errors very small.

Question 15

Why do metering CTs have a lower saturation level than protection CTs?

  1. To save copper only
  2. To protect meters from damage during fault currents
  3. To reduce burden
  4. To increase accuracy at faults
Show answer & solution

Answer: (B) To protect meters from damage during fault currents

Protection CTs must stay accurate at high fault currents.

Question 16

What does a power factor meter indicate?

  1. The cosine of the phase angle between voltage and current
  2. The frequency
  3. The real power only
  4. The energy
Show answer & solution

Answer: (A) The cosine of the phase angle between voltage and current

It may be an electrodynamometer or electronic type.

Question 17

How is three-phase power measured in a balanced three-wire system with a single wattmeter?

  1. By using no wattmeter
  2. By measuring line voltage only
  3. By using a frequency meter
  4. By measuring one phase power and multiplying by three, using an artificial neutral if needed
Show answer & solution

Answer: (D) By measuring one phase power and multiplying by three, using an artificial neutral if needed

The two-wattmeter method is general for three-wire loads.

Question 18

What is a prepaid energy meter?

  1. A meter billed monthly
  2. A meter that supplies electricity only while purchased credit is available
  3. A meter for DC only
  4. A water meter
Show answer & solution

Answer: (B) A meter that supplies electricity only while purchased credit is available

Prepaid meters reduce billing disputes and arrears.

Question 19

What is the purpose of a CT test terminal block in metering panels?

  1. To measure voltage
  2. To store energy
  3. To increase current
  4. To allow CT secondaries to be shorted safely while meters are tested or replaced
Show answer & solution

Answer: (D) To allow CT secondaries to be shorted safely while meters are tested or replaced

Open CT secondaries are dangerous.

Question 20

Which instrument records the variation of voltage, current and power quality over time?

  1. Power quality analyser or data logger
  2. Ballistic galvanometer
  3. Megger
  4. Wheatstone bridge
Show answer & solution

Answer: (A) Power quality analyser or data logger

It records harmonics, sags, swells and flicker.

Question 21

What is the purpose of a voltage transformer in a metering circuit?

  1. To step down high voltage to a standard meter voltage such as 110 V
  2. To step up voltage
  3. To measure current
  4. To store energy
Show answer & solution

Answer: (A) To step down high voltage to a standard meter voltage such as 110 V

It isolates meters from high voltage.

Question 22

What type of CT is used for revenue metering?

  1. A voltage transformer
  2. A CT with no accuracy class
  3. A protection CT of class 5P20 only
  4. A metering CT of high accuracy class such as 0.2 or 0.5
Show answer & solution

Answer: (D) A metering CT of high accuracy class such as 0.2 or 0.5

Revenue meters need high accuracy at normal load.

Question 23

What is the main advantage of electronic energy meters over induction meters?

  1. No display
  2. Higher accuracy, tamper detection and multiple tariff recording
  3. Mechanical parts only
  4. Lower accuracy
Show answer & solution

Answer: (B) Higher accuracy, tamper detection and multiple tariff recording

They measure using digital signal processing.

Question 24

How is reactive energy measured in a three-phase system?

  1. By a megger
  2. By a kWh meter only
  3. By a frequency meter
  4. By a kVARh meter
Show answer & solution

Answer: (D) By a kVARh meter

Utilities charge industrial users for excess reactive energy.

Question 25

Which instrument measures the instantaneous electrical power drawn by a load in watts?

  1. Ohmmeter
  2. Voltmeter
  3. Wattmeter
  4. Ammeter
Show answer & solution

Answer: (C) Wattmeter

Energy is power integrated over time.

Question 26

What is the creep test of an energy meter?

  1. Applying rated voltage with no load to check that the disc does not complete a revolution
  2. Applying full load only
  3. Testing the CT
  4. Testing insulation
Show answer & solution

Answer: (A) Applying rated voltage with no load to check that the disc does not complete a revolution

Creep must be prevented to avoid billing errors.

Question 27

What does a wattmeter reading represent in an AC circuit?

  1. Reactive power
  2. Peak power
  3. Average real power, VI cos φ
  4. Apparent power
Show answer & solution

Answer: (C) Average real power, VI cos φ

Reactive power needs a varmeter.

Question 28

What is phantom loading used for in energy meter testing?

  1. Supplying the voltage and current coils from separate low-power sources to test at full load cheaply
  2. Testing CT polarity only
  3. Measuring insulation
  4. Running meters without any supply
Show answer & solution

Answer: (A) Supplying the voltage and current coils from separate low-power sources to test at full load cheaply

It avoids wasting energy in large test loads.

Question 29

What tamper events do modern static energy meters record?

  1. Room temperature only
  2. Magnetic interference, cover opening, reverse current and neutral missing
  3. Colour changes
  4. Rainfall
Show answer & solution

Answer: (B) Magnetic interference, cover opening, reverse current and neutral missing

Tamper logs help detect electricity theft.

Question 30

What is the unit commonly billed to consumers for energy?

  1. ampere-hour
  2. kilowatt
  3. volt-ampere
  4. kilowatt-hour (kWh), called a unit
Show answer & solution

Answer: (D) kilowatt-hour (kWh), called a unit

One unit equals 1 kWh.

Practice these 30 questions interactively →