Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Measurements & Instrumentation: Bridges and Potentiometers

Electrical Engineering · Measurements & Instrumentation

28 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which bridge circuit is commonly used to measure an unknown medium electrical resistance?

  1. Wien bridge
  2. Schering bridge
  3. Maxwell bridge
  4. Wheatstone bridge
Show answer & solution

Answer: (D) Wheatstone bridge

It is accurate for about 1 Ω to 100 kΩ.

Question 2

What is the unknown resistance S in a balanced Wheatstone bridge with P = 100 Ω, Q = 10 Ω and R = 50 Ω?

  1. 0.5 Ω
  2. 5 Ω
  3. 50 Ω
  4. 500 Ω
Show answer & solution

Answer: (B) 5 Ω

S = RQ/P = 50 × 10/100.

Question 3

Which bridge is used to measure very low resistances below 1 Ω accurately?

  1. Kelvin double bridge
  2. Hay's bridge
  3. Schering bridge
  4. Wheatstone bridge
Show answer & solution

Answer: (A) Kelvin double bridge

It eliminates lead and contact resistance errors.

Question 4

Which bridge is commonly employed to measure an unknown capacitance and dielectric loss?

  1. Anderson bridge
  2. Hay bridge
  3. Schering bridge
  4. Kelvin bridge
Show answer & solution

Answer: (C) Schering bridge

It is used for testing high-voltage cables and insulators.

Question 5

Which bridge is used to measure inductance of medium-Q coils by comparison with a standard capacitor?

  1. Kelvin bridge
  2. Wien bridge
  3. Schering bridge
  4. Maxwell bridge
Show answer & solution

Answer: (D) Maxwell bridge

Maxwell's inductance–capacitance bridge suits coils with Q from 1 to 10.

Question 6

Which bridge is preferred for measuring inductance of high-Q coils?

  1. Wheatstone bridge
  2. Maxwell bridge
  3. Hay's bridge
  4. De Sauty bridge
Show answer & solution

Answer: (C) Hay's bridge

Hay's bridge uses a series RC arm.

Question 7

Which bridge measures self-inductance accurately over a wide range using a capacitor, and is a modification of Maxwell's bridge?

  1. Kelvin bridge
  2. Schering bridge
  3. Wien bridge
  4. Anderson bridge
Show answer & solution

Answer: (D) Anderson bridge

It gives accurate results even for low-Q coils.

Question 8

Which bridge is used to measure frequency in the audio range?

  1. Wien bridge
  2. Maxwell bridge
  3. Kelvin bridge
  4. Hay's bridge
Show answer & solution

Answer: (A) Wien bridge

It is also used as the basis of Wien bridge oscillators.

Question 9

Which simple bridge measures capacitance of a lossless capacitor by comparison with a standard capacitor?

  1. De Sauty bridge
  2. Hay's bridge
  3. Anderson bridge
  4. Kelvin bridge
Show answer & solution

Answer: (A) De Sauty bridge

It cannot measure dielectric loss.

Question 10

What are the balance conditions of an AC bridge?

  1. Only the frequencies must match
  2. Only the resistances must be equal
  3. Only the magnitudes must be equal
  4. Both the magnitudes and the phase angles of opposite-arm impedance products must be equal
Show answer & solution

Answer: (D) Both the magnitudes and the phase angles of opposite-arm impedance products must be equal

Z₁Z₄ = Z₂Z₃ in both magnitude and angle.

Question 11

Which detector is commonly used with AC bridges at audio frequencies?

  1. A megger
  2. A PMMC galvanometer without rectifier
  3. Headphones or an electronic null detector
  4. A thermometer
Show answer & solution

Answer: (C) Headphones or an electronic null detector

Vibration galvanometers are used at power frequencies.

Question 12

What is the purpose of a Wagner earth device in AC bridges?

  1. To increase sensitivity to earth faults
  2. To eliminate errors due to stray capacitance to earth
  3. To earth the supply
  4. To measure earth resistance
Show answer & solution

Answer: (B) To eliminate errors due to stray capacitance to earth

It brings the detector to earth potential at balance.

Question 13

What is the main advantage of a DC potentiometer for voltage measurement?

  1. It is very fast
  2. It measures AC only
  3. It draws no current from the source at balance, giving very accurate results
  4. It needs no standard cell
Show answer & solution

Answer: (C) It draws no current from the source at balance, giving very accurate results

It is a null-balance method.

Question 14

Which method is used to measure very high resistances such as cable insulation?

  1. Maxwell bridge
  2. Hay's bridge
  3. Kelvin double bridge
  4. Loss of charge method or megger test
Show answer & solution

Answer: (D) Loss of charge method or megger test

High resistance measurements need guard circuits to eliminate leakage.

Question 15

What is a guard terminal used for in high resistance measurement?

  1. To bypass surface leakage currents away from the measuring circuit
  2. To increase leakage
  3. To earth the source
  4. To measure voltage
Show answer & solution

Answer: (A) To bypass surface leakage currents away from the measuring circuit

Guarding improves accuracy in insulation testing.

Question 16

Which bridge is a modification of the Wheatstone bridge for comparing two nearly equal resistances?

  1. Hay's bridge
  2. Carey Foster bridge
  3. Anderson bridge
  4. Schering bridge
Show answer & solution

Answer: (B) Carey Foster bridge

It uses a slide wire.

Question 17

What is the effect of using a higher bridge supply voltage on bridge sensitivity?

  1. Sensitivity falls
  2. Sensitivity increases, but heating of resistors must be limited
  3. No effect
  4. The bridge cannot balance
Show answer & solution

Answer: (B) Sensitivity increases, but heating of resistors must be limited

Power dissipation limits the supply voltage.

Question 18

Why is the Schering bridge important for high-voltage insulation testing?

  1. It measures inductance only
  2. It measures frequency
  3. It measures resistance only
  4. It measures capacitance and loss tangent of insulation at high voltage safely
Show answer & solution

Answer: (D) It measures capacitance and loss tangent of insulation at high voltage safely

The high-voltage arms are placed away from the operator.

Question 19

Which bridge uses two potentiometer-like arms to measure resistance of a few milliohms in shunts and busbars?

  1. Wien bridge
  2. De Sauty bridge
  3. Kelvin double bridge
  4. Hay's bridge
Show answer & solution

Answer: (C) Kelvin double bridge

Four-terminal connections remove lead effects.

Question 20

What is the principle of a null-balance measurement?

  1. The unknown is adjusted against a known quantity until a detector shows zero
  2. The meter reads full scale
  3. The current is maximum
  4. The voltage is doubled
Show answer & solution

Answer: (A) The unknown is adjusted against a known quantity until a detector shows zero

Null methods are very accurate because the detector need not be calibrated.

Question 21

What is the condition for balance of Maxwell's inductance–capacitance bridge?

  1. Lx = R1R2R3
  2. Lx = C1/R1
  3. Lx = R2R3C1 and Rx = R2R3/R1
  4. Lx = R1/C1
Show answer & solution

Answer: (C) Lx = R2R3C1 and Rx = R2R3/R1

The balance is independent of frequency.

Question 22

Why is a slide-wire potentiometer standardised before use?

  1. To heat the wire
  2. To set the current so that the wire's voltage per unit length matches a standard cell
  3. To measure resistance
  4. To increase current
Show answer & solution

Answer: (B) To set the current so that the wire's voltage per unit length matches a standard cell

A Weston standard cell or reference provides the standard voltage.

Question 23

What is a crossed-coil ohmmeter (megger) independent of?

  1. The insulation resistance
  2. The pointer position
  3. The test current
  4. Variations in the generator voltage
Show answer & solution

Answer: (D) Variations in the generator voltage

The deflection depends on the ratio of currents in the two coils.

Question 24

Which bridge measures mutual inductance between two coils?

  1. Schering bridge
  2. Heaviside or Campbell bridge
  3. Kelvin bridge
  4. Hay's bridge only
Show answer & solution

Answer: (B) Heaviside or Campbell bridge

Mutual inductance can also be measured with Maxwell's methods.

Question 25

What is the main source of error in measuring low resistances with a Wheatstone bridge?

  1. Lead and contact resistances
  2. Galvanometer colour
  3. Temperature of the room only
  4. Supply frequency
Show answer & solution

Answer: (A) Lead and contact resistances

The Kelvin bridge eliminates these errors.

Question 26

What is the advantage of an AC potentiometer?

  1. It measures DC only
  2. It measures resistance only
  3. It can measure AC voltages in both magnitude and phase
  4. It needs no supply
Show answer & solution

Answer: (C) It can measure AC voltages in both magnitude and phase

Polar and coordinate types exist.

Question 27

What type of supply is used for the Schering bridge in insulation testing?

  1. Battery only
  2. High-voltage AC at power frequency
  3. High-frequency RF only
  4. Low-voltage DC
Show answer & solution

Answer: (B) High-voltage AC at power frequency

It measures capacitance and tan δ under service-like stress.

Question 28

What is the purpose of a vibration galvanometer?

  1. A frequency generator
  2. A wattmeter
  3. A detector for AC bridges at power frequencies
  4. A DC current meter
Show answer & solution

Answer: (C) A detector for AC bridges at power frequencies

It resonates at the supply frequency.

Practice these 28 questions interactively →