Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Measurements & Instrumentation: Digital Instruments

Electrical Engineering · Measurements & Instrumentation

31 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which instrument displays an electrical waveform against time on a screen?

  1. Oscilloscope
  2. Frequency counter
  3. Digital multimeter
  4. Spectrum analyzer
Show answer & solution

Answer: (A) Oscilloscope

It shows amplitude, frequency, phase and distortion.

Question 2

Which instrument displays the amplitude of a signal against frequency?

  1. Clamp meter
  2. Spectrum analyzer
  3. Oscilloscope
  4. Megger
Show answer & solution

Answer: (B) Spectrum analyzer

It is used for analysing harmonics and RF signals.

Question 3

What are Lissajous patterns on an oscilloscope used for?

  1. Comparing frequency and phase of two signals
  2. Measuring temperature
  3. Measuring resistance
  4. Measuring insulation
Show answer & solution

Answer: (A) Comparing frequency and phase of two signals

One signal drives the X plates and the other the Y plates.

Question 4

What is the frequency ratio shown by a Lissajous figure with two horizontal tangencies and one vertical tangency?

  1. 1:1
  2. 1:2
  3. 2:1 (Y to X)
  4. 3:1
Show answer & solution

Answer: (C) 2:1 (Y to X)

The ratio of tangencies gives the frequency ratio.

Question 5

Which type of analogue-to-digital converter is the fastest?

  1. Successive approximation ADC
  2. Counter-type ADC
  3. Dual-slope ADC
  4. Flash (parallel) ADC
Show answer & solution

Answer: (D) Flash (parallel) ADC

It uses many comparators working simultaneously.

Question 6

Which type of ADC is commonly used in digital multimeters because of its noise rejection?

  1. Counter ramp ADC only
  2. Dual-slope integrating ADC
  3. Delta modulator
  4. Flash ADC
Show answer & solution

Answer: (B) Dual-slope integrating ADC

Integration over a power cycle rejects mains noise.

Question 7

Which ADC type offers a good balance of speed and resolution and is common in microcontrollers?

  1. Dual-slope ADC
  2. Voltage-to-frequency ADC
  3. Successive approximation ADC
  4. Flash ADC
Show answer & solution

Answer: (C) Successive approximation ADC

It tests one bit at a time from the most significant bit.

Question 8

What is the resolution of an 8-bit ADC with a 5 V reference?

  1. About 0.625 V
  2. About 5 mV
  3. About 19.5 mV
  4. About 195 mV
Show answer & solution

Answer: (C) About 19.5 mV

Resolution = 5/2⁸ = 5/256 ≈ 19.5 mV.

Question 9

What is the maximum reading of a 3½-digit display?

  1. 999
  2. 1,999
  3. 9,999
  4. 19,999
Show answer & solution

Answer: (B) 1,999

The half digit can be only 0 or 1.

Question 10

What does the Nyquist criterion require when sampling a signal in a digital oscilloscope?

  1. A sampling rate half the signal frequency
  2. A sampling rate equal to the signal frequency
  3. No sampling
  4. A sampling rate of at least twice the highest frequency in the signal
Show answer & solution

Answer: (D) A sampling rate of at least twice the highest frequency in the signal

Undersampling causes aliasing.

Question 11

What is the function of a 10:1 oscilloscope probe?

  1. To reduce loading on the circuit and extend voltage range by attenuating the signal
  2. To increase signal amplitude ten times
  3. To measure current
  4. To filter DC
Show answer & solution

Answer: (A) To reduce loading on the circuit and extend voltage range by attenuating the signal

The probe must be compensated using the scope's calibration signal.

Question 12

Which instrument counts cycles of a signal over a precise time interval to display frequency?

  1. Frequency counter
  2. Megger
  3. Galvanometer
  4. Wheatstone bridge
Show answer & solution

Answer: (A) Frequency counter

It uses a crystal time base.

Question 13

What is a function generator used for?

  1. Measuring resistance
  2. Producing test signals such as sine, square and triangle waves
  3. Measuring power factor
  4. Measuring insulation
Show answer & solution

Answer: (B) Producing test signals such as sine, square and triangle waves

It is used for testing amplifiers and filters.

Question 14

What is an LCR meter?

  1. A frequency meter
  2. An energy meter
  3. A power meter
  4. An instrument that measures inductance, capacitance and resistance
Show answer & solution

Answer: (D) An instrument that measures inductance, capacitance and resistance

It uses AC test signals at selectable frequencies.

Question 15

What does a digital multimeter's "true RMS" feature mean?

  1. It measures the correct RMS value of non-sinusoidal waveforms
  2. It shows average values only
  3. It reads only peak values
  4. It reads only DC
Show answer & solution

Answer: (A) It measures the correct RMS value of non-sinusoidal waveforms

Average-responding meters err on distorted waveforms.

Question 16

What is the main part of an analogue oscilloscope that produces the display?

  1. LCD panel only
  2. Strain gauge
  3. Thermocouple
  4. Cathode ray tube with electron gun and deflection plates
Show answer & solution

Answer: (D) Cathode ray tube with electron gun and deflection plates

Modern digital oscilloscopes use flat-panel displays.

Question 17

What is a data logger?

  1. An oscilloscope probe
  2. A bridge
  3. An instrument that records measurements automatically over time
  4. A transformer
Show answer & solution

Answer: (C) An instrument that records measurements automatically over time

Data loggers monitor temperature, voltage and energy.

Question 18

What is a digital-to-analogue converter (DAC) used for?

  1. Measuring resistance
  2. Converting digital codes into proportional analogue voltages or currents
  3. Measuring frequency
  4. Converting analogue to digital
Show answer & solution

Answer: (B) Converting digital codes into proportional analogue voltages or currents

R-2R ladders are a common DAC design.

Question 19

What is aliasing in digital sampling?

  1. Noise from the probe
  2. Clipping of the signal
  3. DC offset
  4. False lower-frequency components appearing when a signal is sampled too slowly
Show answer & solution

Answer: (D) False lower-frequency components appearing when a signal is sampled too slowly

Anti-aliasing filters remove frequencies above half the sampling rate.

Question 20

What is the main advantage of digital instruments over analogue instruments?

  1. More parallax error
  2. Need for mirror scales
  3. Higher accuracy, no parallax error and easy data storage
  4. Lower accuracy
Show answer & solution

Answer: (C) Higher accuracy, no parallax error and easy data storage

Digital readings can be logged and transmitted.

Question 21

What does the triggering control of an oscilloscope do?

  1. It changes the signal frequency
  2. It synchronises the sweep with the signal to give a stable display
  3. It amplifies current
  4. It measures resistance
Show answer & solution

Answer: (B) It synchronises the sweep with the signal to give a stable display

Edge triggering is the most common mode.

Question 22

How many quantisation levels does a 10-bit ADC have?

  1. 10
  2. 512
  3. 1,000
  4. 1,024
Show answer & solution

Answer: (D) 1,024

2¹⁰ = 1,024.

Question 23

What is the function of the timebase in an oscilloscope?

  1. To amplify the signal
  2. To filter the signal
  3. To sweep the trace horizontally at a known rate
  4. To store energy
Show answer & solution

Answer: (C) To sweep the trace horizontally at a known rate

Timebase settings are given in time per division.

Question 24

What is the period of a waveform that occupies 4 divisions on an oscilloscope set at 5 ms/div?

  1. 1.25 ms
  2. 5 ms
  3. 20 ms
  4. 200 ms
Show answer & solution

Answer: (C) 20 ms

T = 4 × 5 ms; frequency = 50 Hz.

Question 25

What is the peak-to-peak voltage of a waveform occupying 6 vertical divisions at 2 V/div?

  1. 3 V
  2. 6 V
  3. 12 V
  4. 24 V
Show answer & solution

Answer: (C) 12 V

Vpp = 6 × 2 V.

Question 26

What is the main advantage of a digital storage oscilloscope (DSO)?

  1. It is only for DC
  2. It needs no sampling
  3. It cannot store waveforms
  4. It can capture, store and analyse single events and waveforms
Show answer & solution

Answer: (D) It can capture, store and analyse single events and waveforms

DSOs can measure automatically and export data.

Question 27

What is quantisation error in an ADC?

  1. An error due to sampling too fast
  2. A power supply error
  3. An error in the display
  4. The difference between the actual analogue value and the nearest digital level
Show answer & solution

Answer: (D) The difference between the actual analogue value and the nearest digital level

It is at most half the resolution step.

Question 28

What is the resolution of a 12-bit ADC with a 4.096 V reference?

  1. 0.1 mV
  2. 1 mV
  3. 4 mV
  4. 12 mV
Show answer & solution

Answer: (B) 1 mV

4.096/4096 = 0.001 V.

Question 29

What is a remote terminal unit (RTU) used for?

  1. Collecting field data and sending it to a SCADA master station
  2. Testing insulation
  3. Measuring resistance locally only
  4. Generating power
Show answer & solution

Answer: (A) Collecting field data and sending it to a SCADA master station

RTUs are used in grid stations and pipelines.

Question 30

What is the purpose of the bandwidth specification of an oscilloscope?

  1. It shows the probe length
  2. It indicates the highest frequency the scope can measure with small amplitude error
  3. It shows the screen size
  4. It shows the number of channels
Show answer & solution

Answer: (B) It indicates the highest frequency the scope can measure with small amplitude error

A scope's bandwidth should be well above the signal frequency.

Question 31

What is the main use of a power analyser?

  1. Measuring power, power factor, harmonics and efficiency of electrical equipment
  2. Measuring insulation
  3. Measuring wind speed
  4. Measuring temperature only
Show answer & solution

Answer: (A) Measuring power, power factor, harmonics and efficiency of electrical equipment

Power analysers are used for testing drives and inverters.

Practice these 31 questions interactively →