Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Communication & Signals: Noise and Information Theory

Electrical Engineering · Communication & Signals

30 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which quantity compares the desired signal power with the unwanted noise power?

  1. Modulation index
  2. Signal-to-noise ratio
  3. Channel capacity
  4. Frequency deviation
Show answer & solution

Answer: (B) Signal-to-noise ratio

SNR is often given in decibels.

Question 2

What is thermal (Johnson) noise?

  1. Noise generated by random motion of electrons in resistors due to temperature
  2. Noise from lightning only
  3. Noise from mechanical vibration
  4. Noise from digital switching only
Show answer & solution

Answer: (A) Noise generated by random motion of electrons in resistors due to temperature

Its power is kTB.

Question 3

What is the thermal noise power available from a resistor at 290 K in a 1 Hz bandwidth?

  1. About 1 W
  2. About 1 mW
  3. About 1 µW
  4. About 4 × 10⁻²¹ W (−174 dBm)
Show answer & solution

Answer: (D) About 4 × 10⁻²¹ W (−174 dBm)

kT = 1.38 × 10⁻²³ × 290.

Question 4

What is white noise?

  1. Noise that is only at low frequencies
  2. Noise at one frequency
  3. Noise with a flat power spectral density over frequency
  4. Noise with no power
Show answer & solution

Answer: (C) Noise with a flat power spectral density over frequency

Thermal noise is approximately white.

Question 5

What is shot noise?

  1. Noise from mechanical parts
  2. Noise due to the random arrival of discrete charge carriers across a junction
  3. Noise from power lines only
  4. Noise from resistors
Show answer & solution

Answer: (B) Noise due to the random arrival of discrete charge carriers across a junction

It occurs in diodes and transistors.

Question 6

What is flicker (1/f) noise?

  1. High-frequency noise only
  2. Thermal noise
  3. Impulse noise
  4. Low-frequency noise whose power increases as frequency decreases
Show answer & solution

Answer: (D) Low-frequency noise whose power increases as frequency decreases

It matters in low-frequency amplifiers.

Question 7

What is the signal-to-noise ratio in dB if signal power is 100 times noise power?

  1. 10 dB
  2. 20 dB
  3. 40 dB
  4. 100 dB
Show answer & solution

Answer: (B) 20 dB

10 log₁₀(100) = 20 dB.

Question 8

What is the noise figure of an amplifier?

  1. The gain
  2. The bandwidth
  3. The ratio of input SNR to output SNR, usually in dB
  4. The output power
Show answer & solution

Answer: (C) The ratio of input SNR to output SNR, usually in dB

A lower noise figure is better.

Question 9

According to Friis's formula, which stage of a receiver mainly determines its overall noise figure?

  1. The first stage
  2. All stages equally
  3. The last stage
  4. The middle stage
Show answer & solution

Answer: (A) The first stage

A low-noise first amplifier is essential.

Question 10

What does Shannon's theorem give?

  1. The noise figure
  2. The maximum error-free data rate C = B log₂(1 + SNR) for a channel
  3. The modulation index
  4. The bandwidth of FM
Show answer & solution

Answer: (B) The maximum error-free data rate C = B log₂(1 + SNR) for a channel

It sets the theoretical limit of channel capacity.

Question 11

What is the channel capacity of a 3 kHz channel with an SNR of 1,023?

  1. 3 kbps
  2. 10 kbps
  3. 30 kbps
  4. 300 kbps
Show answer & solution

Answer: (C) 30 kbps

C = 3,000 × log₂(1,024) = 3,000 × 10.

Question 12

What is the information content of a message with probability 1/8?

  1. 0.125 bits
  2. 1 bit
  3. 3 bits
  4. 8 bits
Show answer & solution

Answer: (C) 3 bits

I = log₂(1/p) = log₂(8).

Question 13

What is entropy in information theory?

  1. The bandwidth
  2. The noise power
  3. The total number of symbols
  4. The average information per symbol of a source
Show answer & solution

Answer: (D) The average information per symbol of a source

Entropy is maximum when all symbols are equally likely.

Question 14

What is the entropy of a source with two equally likely symbols?

  1. 0 bits
  2. 0.5 bits per symbol
  3. 1 bit per symbol
  4. 2 bits per symbol
Show answer & solution

Answer: (C) 1 bit per symbol

H = −2 × 0.5 log₂(0.5) = 1.

Question 15

What is 0 dBm equal to?

  1. 0 W
  2. 1 W
  3. 1 mW
  4. 1 µW
Show answer & solution

Answer: (C) 1 mW

dBm is power relative to 1 mW.

Question 16

What power does 30 dBm represent?

  1. 1 W
  2. 10 W
  3. 30 mW
  4. 100 mW
Show answer & solution

Answer: (A) 1 W

30 dB above 1 mW is 1,000 mW.

Question 17

What does an increase of 3 dB in power represent?

  1. Approximately a doubling of power
  2. A tenfold increase
  3. A halving
  4. No change
Show answer & solution

Answer: (A) Approximately a doubling of power

−3 dB is approximately half power.

Question 18

What is noise temperature?

  1. The temperature of a resistor only
  2. The boiling point
  3. The physical temperature of a room
  4. An equivalent temperature that represents the noise power of a device or system
Show answer & solution

Answer: (D) An equivalent temperature that represents the noise power of a device or system

It is used in satellite receiver design.

Question 19

How does thermal noise power change if the bandwidth is doubled?

  1. It is unchanged
  2. It doubles
  3. It halves
  4. It becomes four times
Show answer & solution

Answer: (B) It doubles

Noise power is proportional to bandwidth.

Question 20

What is impulse noise?

  1. Thermal noise
  2. Short bursts of high-amplitude noise from sources such as lightning and switching
  3. Noise from quantisation only
  4. White noise only
Show answer & solution

Answer: (B) Short bursts of high-amplitude noise from sources such as lightning and switching

It causes clicks in audio and bursts of bit errors.

Question 21

What is the main way to improve channel capacity according to Shannon's formula?

  1. Increasing bandwidth or signal-to-noise ratio
  2. Reducing power to zero
  3. Increasing noise
  4. Reducing bandwidth
Show answer & solution

Answer: (A) Increasing bandwidth or signal-to-noise ratio

Capacity grows linearly with bandwidth and logarithmically with SNR.

Question 22

What is crosstalk?

  1. Quantisation noise
  2. Thermal noise
  3. Shot noise
  4. Unwanted coupling of signals from one circuit or channel into another
Show answer & solution

Answer: (D) Unwanted coupling of signals from one circuit or channel into another

Twisted pairs reduce crosstalk.

Question 23

What is the signal-to-noise ratio in dB if signal power is 1 W and noise power is 1 mW?

  1. 3 dB
  2. 30 dB
  3. 60 dB
  4. 1,000 dB
Show answer & solution

Answer: (B) 30 dB

10 log₁₀(1,000) = 30 dB.

Question 24

What is the noise power kTB in a 1 MHz bandwidth at 290 K?

  1. About 4 W
  2. About 4 × 10⁻²¹ W
  3. About 4 × 10⁻¹⁵ W
  4. About 4 × 10⁻⁹ W
Show answer & solution

Answer: (C) About 4 × 10⁻¹⁵ W

4 × 10⁻²¹ W/Hz × 10⁶ Hz.

Question 25

What is the effect of a cascade of amplifiers with high gain in the first stage on overall noise figure?

  1. The overall noise figure is close to that of the first stage
  2. It becomes zero
  3. It becomes infinite
  4. It equals the last stage
Show answer & solution

Answer: (A) The overall noise figure is close to that of the first stage

Later stages are divided by the gain of earlier stages.

Question 26

What is the voltage ratio corresponding to 20 dB?

  1. 2
  2. 10
  3. 20
  4. 100
Show answer & solution

Answer: (B) 10

20 log₁₀(10) = 20 dB.

Question 27

What is channel capacity?

  1. The maximum rate at which information can be sent over a channel with arbitrarily small error
  2. The number of users
  3. The bandwidth of the channel
  4. The power of the transmitter
Show answer & solution

Answer: (A) The maximum rate at which information can be sent over a channel with arbitrarily small error

Shannon's formula gives it for Gaussian noise.

Question 28

What is redundancy in source coding?

  1. Information that must always be added
  2. Noise
  3. The carrier
  4. Extra information beyond the minimum needed, which compression removes
Show answer & solution

Answer: (D) Extra information beyond the minimum needed, which compression removes

Huffman coding reduces redundancy.

Question 29

What is Huffman coding?

  1. A modulation scheme
  2. An error-correcting code
  3. A variable-length code that gives shorter codewords to more probable symbols
  4. A fixed-length code
Show answer & solution

Answer: (C) A variable-length code that gives shorter codewords to more probable symbols

It approaches the source entropy.

Question 30

What is the main source of noise in satellite receiver front ends?

  1. Thermal noise in the first amplifier and antenna
  2. Mechanical vibration
  3. Shot noise from batteries
  4. Lightning only
Show answer & solution

Answer: (A) Thermal noise in the first amplifier and antenna

Low-noise block converters minimise it.

Practice these 30 questions interactively →