Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Communication & Signals: Digital Communication

Electrical Engineering · Communication & Signals

30 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What are the three main steps of pulse code modulation (PCM)?

  1. Sampling, quantisation and encoding
  2. Amplification, filtering and modulation
  3. Mixing, detection and amplification
  4. Coding, decoding and storing
Show answer & solution

Answer: (A) Sampling, quantisation and encoding

PCM converts analog signals into binary codes.

Question 2

What is the bit rate of a PCM telephone channel sampled at 8 kHz with 8 bits per sample?

  1. 8 kbps
  2. 16 kbps
  3. 64 kbps
  4. 128 kbps
Show answer & solution

Answer: (C) 64 kbps

8,000 × 8 = 64,000 bits per second.

Question 3

By about how much does the signal-to-quantisation-noise ratio of PCM improve for each extra bit?

  1. About 1 dB
  2. About 3 dB
  3. About 6 dB
  4. About 20 dB
Show answer & solution

Answer: (C) About 6 dB

SQNR ≈ 6.02n + 1.76 dB for a full-scale sine wave.

Question 4

What is companding in PCM?

  1. Increasing bandwidth
  2. Compressing the signal before quantisation and expanding it after decoding to improve SNR for weak signals
  3. Removing noise
  4. Amplifying all signals equally
Show answer & solution

Answer: (B) Compressing the signal before quantisation and expanding it after decoding to improve SNR for weak signals

A-law companding is used in E1 telephone systems.

Question 5

What problem occurs in delta modulation when the input changes faster than the step size can follow?

  1. Aliasing only
  2. Slope overload distortion
  3. Granular noise only
  4. Crosstalk
Show answer & solution

Answer: (B) Slope overload distortion

Adaptive delta modulation varies the step size.

Question 6

Which digital modulation varies the amplitude of the carrier between two levels?

  1. Amplitude shift keying (ASK)
  2. Frequency shift keying (FSK)
  3. Phase shift keying (PSK)
  4. QAM only
Show answer & solution

Answer: (A) Amplitude shift keying (ASK)

On–off keying is the simplest form of ASK.

Question 7

Which digital modulation changes the carrier frequency to represent binary data?

  1. ASK
  2. PCM
  3. PSK
  4. Frequency shift keying (FSK)
Show answer & solution

Answer: (D) Frequency shift keying (FSK)

FSK was used in early modems.

Question 8

How many bits does each QPSK symbol carry?

  1. 1
  2. 2
  3. 4
  4. 8
Show answer & solution

Answer: (B) 2

QPSK has four phase states.

Question 9

How many bits does each 16-QAM symbol carry?

  1. 2
  2. 4
  3. 8
  4. 16
Show answer & solution

Answer: (B) 4

16 = 2⁴ combinations of amplitude and phase.

Question 10

What does bit error rate (BER) measure?

  1. The fraction of received bits that are in error
  2. The bandwidth
  3. The data rate
  4. The carrier frequency
Show answer & solution

Answer: (A) The fraction of received bits that are in error

BER falls as SNR increases.

Question 11

Which method assigns separate time intervals to different transmitted signals?

  1. Frequency modulation
  2. Phase-shift keying
  3. Amplitude limiting
  4. Time-division multiplexing
Show answer & solution

Answer: (D) Time-division multiplexing

Each channel uses the full bandwidth in its time slot.

Question 12

What does frequency-division multiplexing (FDM) do?

  1. Assigns different frequency bands to different signals on the same medium
  2. Codes signals with keys
  3. Uses separate cables
  4. Assigns time slots
Show answer & solution

Answer: (A) Assigns different frequency bands to different signals on the same medium

Radio and TV broadcasting use FDM.

Question 13

What is the data rate of an E1 digital transmission system?

  1. 1.544 Mbps
  2. 2.048 Mbps
  3. 10 Mbps
  4. 64 kbps
Show answer & solution

Answer: (B) 2.048 Mbps

E1 carries 32 time slots of 64 kbps each.

Question 14

What is the difference between bit rate and baud rate?

  1. Bit rate counts symbols
  2. They are always equal
  3. Bit rate counts bits per second; baud rate counts symbols per second
  4. Baud rate is always higher
Show answer & solution

Answer: (C) Bit rate counts bits per second; baud rate counts symbols per second

With multi-bit symbols, bit rate exceeds baud rate.

Question 15

What is intersymbol interference (ISI)?

  1. Interference from other users only
  2. Quantisation error
  3. Noise from the sun
  4. Overlap of adjacent symbols caused by channel bandwidth limits and dispersion
Show answer & solution

Answer: (D) Overlap of adjacent symbols caused by channel bandwidth limits and dispersion

Pulse shaping and equalisers reduce ISI.

Question 16

What does an eye diagram show?

  1. The carrier frequency
  2. The modulation index
  3. The quality of a digital signal, including noise and ISI
  4. The antenna pattern
Show answer & solution

Answer: (C) The quality of a digital signal, including noise and ISI

A wide open eye indicates good signal quality.

Question 17

What is Manchester coding?

  1. A line code with a transition in the middle of every bit, giving self-clocking
  2. An analog modulation
  3. A compression code
  4. A code without transitions
Show answer & solution

Answer: (A) A line code with a transition in the middle of every bit, giving self-clocking

It was used in classic Ethernet.

Question 18

What is spread spectrum communication?

  1. A DC transmission
  2. A technique that spreads a signal over a wide bandwidth to resist interference and allow multiple access
  3. A type of filtering
  4. A narrowband AM system
Show answer & solution

Answer: (B) A technique that spreads a signal over a wide bandwidth to resist interference and allow multiple access

CDMA and GPS use spread spectrum.

Question 19

What is OFDM?

  1. Orthogonal frequency-division multiplexing, which sends data on many closely spaced orthogonal subcarriers
  2. An analog FM system
  3. A single-carrier AM system
  4. A pulse width system
Show answer & solution

Answer: (A) Orthogonal frequency-division multiplexing, which sends data on many closely spaced orthogonal subcarriers

OFDM is used in 4G, 5G and Wi-Fi.

Question 20

What is the main advantage of digital communication over analog communication?

  1. Lower bandwidth always
  2. Simpler equipment always
  3. No need for synchronisation
  4. Better noise immunity, regeneration of signals and easy encryption
Show answer & solution

Answer: (D) Better noise immunity, regeneration of signals and easy encryption

Repeaters can regenerate digital signals without accumulating noise.

Question 21

What is a CRC used for in digital communication?

  1. Correcting all errors
  2. Modulating carriers
  3. Detecting errors in blocks of data
  4. Synchronising clocks
Show answer & solution

Answer: (C) Detecting errors in blocks of data

Cyclic redundancy checks are widely used in data links.

Question 22

What is the minimum bandwidth needed to transmit data at R bits per second using binary signalling without ISI (Nyquist)?

  1. 2R
  2. R/4
  3. R
  4. R/2
Show answer & solution

Answer: (D) R/2

Practical systems need more because of roll-off.

Question 23

What is pulse amplitude modulation (PAM)?

  1. A pulse modulation where the amplitude of pulses varies with the message
  2. A digital code
  3. A modulation of frequency
  4. A modulation of phase only
Show answer & solution

Answer: (A) A pulse modulation where the amplitude of pulses varies with the message

PAM is a step towards PCM.

Question 24

What is differential PCM (DPCM)?

  1. A method that encodes full samples only
  2. An analog method
  3. A PCM method that encodes the difference between successive samples to reduce bit rate
  4. A noise source
Show answer & solution

Answer: (C) A PCM method that encodes the difference between successive samples to reduce bit rate

It exploits correlation between samples.

Question 25

What is the bit rate of a system transmitting 2,400 symbols per second using 16-QAM?

  1. 2,400 bps
  2. 4,800 bps
  3. 9,600 bps
  4. 38,400 bps
Show answer & solution

Answer: (C) 9,600 bps

16-QAM carries 4 bits per symbol.

Question 26

What is the bandwidth efficiency of higher-order QAM compared with BPSK?

  1. Lower
  2. Zero
  3. The same
  4. Higher, because more bits are sent per symbol
Show answer & solution

Answer: (D) Higher, because more bits are sent per symbol

Higher-order QAM needs higher SNR.

Question 27

What is the main purpose of a raised-cosine filter in digital transmission?

  1. To shape pulses so as to limit bandwidth and minimise ISI
  2. To modulate the carrier
  3. To add noise
  4. To increase ISI
Show answer & solution

Answer: (A) To shape pulses so as to limit bandwidth and minimise ISI

The roll-off factor sets excess bandwidth.

Question 28

What is BPSK?

  1. An amplitude modulation
  2. A frequency modulation
  3. Binary phase shift keying with two carrier phases 180° apart
  4. A four-phase modulation
Show answer & solution

Answer: (C) Binary phase shift keying with two carrier phases 180° apart

BPSK is robust against noise.

Question 29

Which multiple access technique gives each user a unique code and lets all users share the same band at the same time?

  1. TDMA
  2. CDMA
  3. FDMA
  4. SDMA only
Show answer & solution

Answer: (B) CDMA

It was used in 3G systems.

Question 30

What is the main advantage of error-correcting codes such as convolutional and turbo codes?

  1. They allow the receiver to correct errors without retransmission
  2. They reduce bandwidth to zero
  3. They need no extra bits
  4. They increase errors
Show answer & solution

Answer: (A) They allow the receiver to correct errors without retransmission

They are essential in mobile and satellite links.

Practice these 30 questions interactively →