Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Surveying: Theodolite Surveying, Traversing and Curve Setting

Civil Engineering · Surveying

40 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

A theodolite is a precision instrument used mainly to measure

  1. magnetic bearings of lines
  2. differences of elevation using a horizontal line of sight
  3. horizontal and vertical angles
  4. horizontal distances directly with an invar tape
Show answer & solution

Answer: (C) horizontal and vertical angles

The theodolite's main function is the accurate measurement of horizontal and vertical angles.

Question 2

The vertical circle of a theodolite is used to measure

  1. vertical angles of elevation or depression to a target
  2. the height of the instrument above the ground at the station
  3. the magnetic bearing of the line of sight from the north
  4. horizontal angles between two stations seen from the instrument
Show answer & solution

Answer: (A) vertical angles of elevation or depression to a target

The vertical circle gives the inclination of the line of sight to the horizontal.

Question 3

The horizontal circle of a theodolite is used to measure

  1. horizontal angles between the directions to two points
  2. the slope of the line of sight to the target, in per cent
  3. the height of the instrument above the station mark
  4. vertical angles of elevation or depression to a distant target
Show answer & solution

Answer: (A) horizontal angles between the directions to two points

The horizontal circle reads the directions of the lines, and the difference of two readings is the horizontal angle.

Question 4

Observations on face left and face right are averaged in order to

  1. remove the error caused by the centring of the instrument not being exactly over the station
  2. eliminate errors from imperfect adjustment of the instrument, such as collimation
  3. remove the error caused by the plate levels not being set accurately
  4. halve the least count of the instrument
Show answer & solution

Answer: (B) eliminate errors from imperfect adjustment of the instrument, such as collimation

Changing face reverses the effect of the collimation and transverse axis errors, which then cancel in the mean.

Question 5

The accuracy of a closed theodolite traverse can be checked by confirming that

  1. the interior angles total 360° and the sum of the latitudes equals the sum of the departures
  2. the exterior angles total (2n − 4) right angles and the sum of the bearings is 360°
  3. the interior angles total (2n + 4) right angles and the sums of latitudes and departures equal the perimeter
  4. the interior angles total (2n − 4) right angles, and ΣL and ΣD are each nearly zero
Show answer & solution

Answer: (D) the interior angles total (2n − 4) right angles, and ΣL and ΣD are each nearly zero

A closed traverse has an angular check on the sum of the angles and a linear check on the closure of latitudes and departures.

Question 6

A closed traverse is one in which

  1. every line is measured twice, in opposite directions
  2. the lines form a closed polygon, or begin and end at points of known position
  3. the lines start at a point of known position and end at a point of unknown position
  4. all the sides are of equal length
Show answer & solution

Answer: (B) the lines form a closed polygon, or begin and end at points of known position

A closed traverse returns to its starting point or to another known point, which gives checks on the work.

Question 7

An open traverse is one in which the lines

  1. run in a single straight line between two stations, with no change of direction
  2. begin and end at two stations of known coordinates, giving a check at the end
  3. return to the starting point, which gives a check on the angles and on the closing error
  4. do not close on the starting point or on another known point, as in a road survey
Show answer & solution

Answer: (D) do not close on the starting point or on another known point, as in a road survey

An open traverse has no closing check, so it needs extra care in observation and checking.

Question 8

The latitude of a survey line is

  1. its projection on the east-west line, equal to length × sine of the bearing
  2. its projection on the meridian, equal to length × cosine of the bearing
  3. its length multiplied by the tangent of the bearing
  4. its projection on the direction of the previous line of the traverse
Show answer & solution

Answer: (B) its projection on the meridian, equal to length × cosine of the bearing

Latitude is the north-south component of a line, L cos θ, positive for northing.

Question 9

The departure of a survey line is

  1. the difference between its length and its latitude
  2. its length divided by the sine of the bearing
  3. its projection on the meridian, equal to the length of the line × cosine of the bearing
  4. its projection on the east-west line, equal to length × sine of the bearing
Show answer & solution

Answer: (D) its projection on the east-west line, equal to length × sine of the bearing

Departure is the east-west component of a line, L sin θ, positive for easting.

Question 10

For a closed traverse free from error, the algebraic sum of the latitudes and the algebraic sum of the departures are

  1. each equal to the perimeter divided by the number of sides
  2. each equal to half the perimeter
  3. each equal to zero
  4. equal to each other and to the perimeter
Show answer & solution

Answer: (C) each equal to zero

A closed traverse returns to its starting point, so the net north-south and east-west displacements are each zero.

Question 11

The linear error of closure of a traverse, in terms of the sums of latitudes (ΣL) and departures (ΣD), is

  1. ΣL × ΣD
  2. √[(ΣL)² + (ΣD)²]
  3. √[(ΣL)² − (ΣD)²]
  4. ΣL + ΣD
Show answer & solution

Answer: (B) √[(ΣL)² + (ΣD)²]

The closing error is the resultant of the latitude and departure misclosures, the hypotenuse of a right triangle.

Question 12

In Bowditch's rule for adjusting a closed traverse, the correction to the latitude or departure of a line is proportional to

  1. the magnitude of that latitude or departure divided by the sum of all latitudes or departures
  2. the reciprocal of the length of that line
  3. the length of that line divided by the perimeter of the traverse
  4. an equal share for every line, whatever its length
Show answer & solution

Answer: (C) the length of that line divided by the perimeter of the traverse

Bowditch's (compass) rule distributes the total misclosure in proportion to line lengths.

Question 13

In the transit rule for adjusting a closed traverse, the correction to the latitude or departure of a line is proportional to

  1. the reciprocal of the length of that line, divided by the sum of reciprocals
  2. the magnitude of that latitude or departure divided by the arithmetic sum of all latitudes or departures
  3. the length of that line divided by the total perimeter of the whole closed traverse
  4. the bearing of that line divided by the sum of the bearings of all the lines
Show answer & solution

Answer: (B) the magnitude of that latitude or departure divided by the arithmetic sum of all latitudes or departures

The transit rule is suited to traverses in which the angles are measured more precisely than the lengths.

Question 14

The area enclosed by a closed traverse can be computed from the latitudes and departures by the

  1. mid-ordinate rule for areas from offsets
  2. prismoidal formula for earthwork volumes
  3. tangential angle method of Rankine
  4. double meridian distance method
Show answer & solution

Answer: (D) double meridian distance method

The DMD method uses the DMD and latitude of each line to give twice the enclosed area.

Question 15

In a theodolite traverse, the angle measured at each station between the preceding line and the following line is used in the method of

  1. included (interior) angles
  2. deflection angles
  3. radiation from a single central station
  4. direct (fast-needle) bearings
Show answer & solution

Answer: (A) included (interior) angles

In the method of included angles, each station angle is observed between adjacent lines, and the bearings are computed from them.

Question 16

When a theodolite traverse is run by orienting the horizontal circle by the magnetic needle at each station so that the bearings of the lines are read directly, it is called

  1. the fast-needle (direct bearings) method
  2. the method of included angles at each station
  3. plane table traversing along the same route
  4. the method of deflection angles from the produced line
Show answer & solution

Answer: (A) the fast-needle (direct bearings) method

Reading the bearing of every line directly from the circle oriented at the station is the fast-needle method.

Question 17

The sum of the interior angles of a closed traverse of n sides is

  1. (2n − 4) × 90°
  2. (n − 1) × 180°
  3. 360°
  4. (2n + 4) × 90°
Show answer & solution

Answer: (A) (2n − 4) × 90°

The interior angles of any simple polygon add up to (n − 2) × 180°, which equals (2n − 4) right angles.

Question 18

For a closed traverse run clockwise, the algebraic sum of the deflection angles, taking right deflections as positive and left deflections as negative, is

  1. (2n − 4) × 90°
  2. 360°
  3. (2n + 4) × 90°
  4. 180°
Show answer & solution

Answer: (B) 360°

The directions of the lines turn through one complete revolution in going round a closed traverse, so the algebraic sum is 360°.

Question 19

The permissible ratio of the linear error of closure of a traverse to its perimeter

  1. is applied to the angular misclosure of the traverse and not to the linear error
  2. is fixed at 1 in 1000 for all traverses, whatever the purpose or order of the survey
  3. varies with the required precision of the survey, being tighter for control work than for reconnaissance
  4. depends on the number of stations in the traverse and not on its purpose
Show answer & solution

Answer: (C) varies with the required precision of the survey, being tighter for control work than for reconnaissance

The relative closing error is judged against a limit chosen to suit the order and purpose of the work.

Question 20

Balancing a traverse means

  1. distributing the small closing error among the lines by a rule such as Bowditch's
  2. making the lengths of all the sides of the traverse equal
  3. applying the whole closing error to the last line of the traverse
  4. repeating the whole traverse in the field until the closing error becomes exactly zero
Show answer & solution

Answer: (A) distributing the small closing error among the lines by a rule such as Bowditch's

Balancing spreads the acceptable misclosure over all the lines by a systematic rule, so the plotted traverse closes exactly.

Question 21

The computed and adjusted coordinates of the traverse stations are useful because they

  1. convert the magnetic bearings of the lines into true bearings
  2. remove the need for control points in any later survey
  3. allow stations to be plotted directly and used for areas and setting out
  4. replace the check on the closing error of the traverse by a graphical check
Show answer & solution

Answer: (C) allow stations to be plotted directly and used for areas and setting out

Coordinates give the stations a common reference so that plotting, areas and setting out do not need the original angles and distances.

Question 22

A point can be set out on the ground by theodolite intersection by

  1. measuring a distance from one known station and an angle at that station to the required point
  2. measuring perpendicular offsets from a chain line to the point
  3. sighting from two known stations along computed directions and marking where the lines meet
  4. observing a single horizontal angle at the point itself to two known stations
Show answer & solution

Answer: (C) sighting from two known stations along computed directions and marking where the lines meet

Setting out by intersection uses two known stations and directions computed from the design coordinates.

Question 23

A simple circular curve on a highway or railway is defined mainly by

  1. its length between the tangent points and the width of the formation
  2. the difference in elevation between its two ends
  3. the design speed and the type of traffic using the road
  4. its radius and the deflection angle of the tangents
Show answer & solution

Answer: (D) its radius and the deflection angle of the tangents

The radius (or degree of curve) and the deflection angle fix the tangent length, the curve length and the other elements.

Question 24

The point at which a straight alignment ends and a simple curve begins is called the

  1. point of intersection (PI)
  2. point of tangency (PT)
  3. mid-point of the curve
  4. point of curvature (PC)
Show answer & solution

Answer: (D) point of curvature (PC)

The PC is the beginning of the curve on the incoming tangent, and the PT is where the curve ends.

Question 25

A compound curve consists of

  1. a simple curve joined to a straight line through a spiral
  2. two or more simple curves of different radii turning the same way, joined at a common tangent point
  3. two simple curves of equal radius turning the same way
  4. two simple curves of different radii turning in opposite directions, joined at a common tangent
Show answer & solution

Answer: (B) two or more simple curves of different radii turning the same way, joined at a common tangent point

The arcs of a compound curve have a common tangent at their junction and bend in the same direction.

Question 26

A reverse curve consists of

  1. two arcs of different radii turning in the same direction, joined without a straight
  2. a curve in a vertical plane connecting two gradients
  3. one curve whose radius changes gradually along its length
  4. two arcs turning in opposite directions, with a common tangent at their junction, giving an S shape
Show answer & solution

Answer: (D) two arcs turning in opposite directions, with a common tangent at their junction, giving an S shape

In a reverse curve the centres of the two arcs lie on opposite sides of the common tangent.

Question 27

The radius of a transition curve joining a straight to a circular curve

  1. is constant and equal to the radius of the circular curve
  2. varies from the radius of the circular curve down to zero at the end of the straight
  3. varies from zero at the straight to infinity at the circular curve
  4. varies from infinity at the straight to that of the circular curve at the other end
Show answer & solution

Answer: (D) varies from infinity at the straight to that of the circular curve at the other end

The curvature of a transition curve increases from zero at the tangent to the curvature of the circular curve.

Question 28

Transition curves are provided on highways and railways mainly to

  1. shorten the length of the circular curve and so reduce the cost of the alignment
  2. remove the need for superelevation on the circular curve of the alignment
  3. introduce centrifugal force and superelevation gradually
  4. reduce the deflection angle between the two tangents of the alignment
Show answer & solution

Answer: (C) introduce centrifugal force and superelevation gradually

A vehicle entering a circular curve from a straight experiences a sudden lateral force, which a transition curve spreads over some length.

Question 29

A vertical curve connects two gradients in the longitudinal profile of a road mainly to

  1. provide a smooth change in direction in plan between two tangents
  2. allow superelevation to be applied on the curve
  3. reduce the length of the horizontal curve
  4. provide a smooth change of grade at the point where the gradients meet
Show answer & solution

Answer: (D) provide a smooth change of grade at the point where the gradients meet

Without a vertical curve there would be an abrupt break of grade at the intersection of the two gradients.

Question 30

A summit (crest) vertical curve is one that is

  1. concave upward, as at the bottom of a valley
  2. formed by two equal gradients of the same sign
  3. convex upward, as at the top of a hill
  4. governed in length by the headlight beam distance at night
Show answer & solution

Answer: (C) convex upward, as at the top of a hill

A summit curve joins an upgrade to a downgrade (or to a flatter upgrade), so its profile is convex upward.

Question 31

A sag (valley) vertical curve is one that is

  1. governed in length by the stopping distance over a crest
  2. convex upward, as at the top of a hill, connecting an upgrade to a downgrade
  3. an arc of a circle of large radius laid out in the horizontal plane
  4. concave upward, joining a downgrade to an upgrade
Show answer & solution

Answer: (D) concave upward, joining a downgrade to an upgrade

A sag curve is concave upward and joins a falling grade to a rising one.

Question 32

In setting out a circular curve by offsets from the long chord, the offsets are calculated from

  1. the lengths of the two tangents and the chainage of the point of intersection
  2. the difference in elevation between the two ends of the chord
  3. the radius of the curve and the geometry of the arc and chord
  4. the magnetic bearing of the long chord and the length of the tangents
Show answer & solution

Answer: (C) the radius of the curve and the geometry of the arc and chord

The offset at any distance from the mid-point of the chord follows from the circle geometry: y = √(R² − x²) − (R − O₀).

Question 33

Setting out a curve by offsets from the tangent is convenient mainly for

  1. short curves that can be laid out wholly from the tangent
  2. vertical curves joining two gradients of small difference
  3. long curves of large radius, running to several hundred metres in length
  4. curves whose tangent points are inaccessible because of obstructions
Show answer & solution

Answer: (A) short curves that can be laid out wholly from the tangent

Offsets from the tangent grow quickly with distance, so the method suits short curves.

Question 34

In Rankine's method of tangential angles for setting out a circular curve,

  1. two theodolites are set up at the PC and the PT, and each point is fixed by their intersection
  2. a theodolite at the PC lays off deflection angles from the tangent, and chords are measured
  3. perpendicular offsets are measured from the long chord at equal intervals along it
  4. each point is fixed by an offset from the previous chord produced, with a tape only
Show answer & solution

Answer: (B) a theodolite at the PC lays off deflection angles from the tangent, and chords are measured

Rankine's method is the common deflection angle method for longer curves, using one theodolite at the PC.

Question 35

In Rankine's method, the deflection angle for a chord of length l on a curve of radius R is

  1. half the central angle subtended by the chord
  2. equal to the total deflection angle between the tangents
  3. equal to the central angle subtended by the chord
  4. independent of the radius, depending on the chord length only
Show answer & solution

Answer: (A) half the central angle subtended by the chord

The tangent-chord angle equals half the angle at the centre, giving δ = l/2R radians.

Question 36

In setting out a curve, the chainages of the PC, PT and other points are measured from

  1. the centre of each curve, restarted afresh for every curve of the alignment
  2. a single fixed starting point of the whole alignment
  3. the point of intersection of the previous curve
  4. the nearest bench mark along the alignment
Show answer & solution

Answer: (B) a single fixed starting point of the whole alignment

Chainage is cumulative distance along the alignment from one consistent starting point.

Question 37

In setting out compound and reverse curves, particular care is needed to ensure that

  1. a straight length of equal size lies between the two arcs at the junction
  2. the two arcs have equal radii and equal lengths, whatever the deflection angles
  3. the two arcs have a common tangent at the point of compound or reverse curvature
  4. the tangent lengths of the two arcs are equal at the junction point
Show answer & solution

Answer: (C) the two arcs have a common tangent at the point of compound or reverse curvature

The arcs must join tangentially at their junction, otherwise there would be a sharp change of direction.

Question 38

The shape commonly adopted for transition curves in highway and railway work, with curvature increasing uniformly with length, is

  1. a circular arc of twice the radius of the main circular curve
  2. a clothoid spiral, or a cubic parabola as an approximation
  3. an ellipse centred at the point of intersection of the tangents
  4. a quadratic parabola, as used for vertical curves
Show answer & solution

Answer: (B) a clothoid spiral, or a cubic parabola as an approximation

In a spiral the radius is inversely proportional to the length measured from the start, so the curvature rises uniformly.

Question 39

The elevation of an intermediate point on a vertical curve is calculated from

  1. the elevation and gradients of the tangents, using the equation of a parabola
  2. the radius of the horizontal curve at the same chainage of the road
  3. interpolation between the contour lines of the map
  4. the bearings of the tangents of the alignment
Show answer & solution

Answer: (A) the elevation and gradients of the tangents, using the equation of a parabola

A vertical curve is taken as a parabola, so the offset from the tangent at distance x is proportional to x².

Question 40

The length of a summit vertical curve on a highway is governed mainly by

  1. the stopping (or overtaking) sight distance at the design speed
  2. the superelevation needed at the design speed
  3. the rate of change of centrifugal acceleration
  4. the headlight beam distance required at night for the design speed
Show answer & solution

Answer: (A) the stopping (or overtaking) sight distance at the design speed

Driver sight distance over the crest limits the speed, so the curve must be long enough to give the required sight distance.

Practice these 40 questions interactively →