Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Surveying: Levelling, Contouring and Plane Tabling

Civil Engineering · Surveying

43 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Levelling is the process of determining

  1. the relative elevations of points with respect to a common datum
  2. the directions of the survey lines with respect to the north meridian
  3. the horizontal distances between points that lie on sloping ground
  4. the horizontal angles between the survey lines meeting at a station
Show answer & solution

Answer: (A) the relative elevations of points with respect to a common datum

Levelling gives the vertical relationship of points, expressed as reduced levels above a datum.

Question 2

A bench mark is a fixed point

  1. of known and reasonably permanent elevation, used as a reference for levelling
  2. on which a fore sight and a back sight are taken to carry the levels forward
  3. of known northing and easting, but whose elevation is not recorded in the survey
  4. on which an intermediate sight is taken between two setups
Show answer & solution

Answer: (A) of known and reasonably permanent elevation, used as a reference for levelling

Bench marks give stable elevations from which other levels are carried forward and to which levelling circuits are closed.

Question 3

A dumpy level is used mainly to

  1. provide a horizontal line of sight, so that staff readings give differences of elevation
  2. set out right angles to the chain lines for taking offsets
  3. determine the magnetic bearings of the survey lines from the north direction
  4. measure horizontal and vertical angles with its graduated circles in a single setup
Show answer & solution

Answer: (A) provide a horizontal line of sight, so that staff readings give differences of elevation

The dumpy level gives a horizontal sight line, and readings on a staff then give height differences.

Question 4

The line of collimation of a levelling instrument is the line

  1. tangential to the longitudinal curve of the bubble tube at its centre point
  2. joining the optical centre of the object glass to the intersection of the cross hairs
  3. passing through the vertical axis of rotation of the instrument and its tripod head
  4. joining the optical centre of the object glass to the optical centre of the eye-piece lens
Show answer & solution

Answer: (B) joining the optical centre of the object glass to the intersection of the cross hairs

This line defines the line of sight along which the staff is read.

Question 5

A levelling staff is held on a point so that the level can

  1. read the vertical distance between the line of sight and that point
  2. fix the horizontal distance between two instrument stations
  3. mark the line of sight at a constant height above the ground
  4. measure the vertical angle between the instrument and that point on the ground
Show answer & solution

Answer: (A) read the vertical distance between the line of sight and that point

The staff reading, with the height of the line of sight, gives the elevation of the point on which the staff stands.

Question 6

A back sight (BS) in levelling is a staff reading taken

  1. on a point lying between the first and last readings of a setup
  2. on a point of known elevation, to find the height of instrument
  3. as the last reading from a setup, before the instrument is shifted
  4. on a new point, to compute its elevation from the height of instrument
Show answer & solution

Answer: (B) on a point of known elevation, to find the height of instrument

A back sight on a point of known level, added to that level, gives the height of the line of sight for the setup.

Question 7

A fore sight (FS) in levelling is a staff reading taken

  1. only on bench marks of known elevation
  2. on any point lying between the back sight and the next setup
  3. as the first reading after setting up on a point of known elevation
  4. as the last reading from a setup, to find the level of a new point
Show answer & solution

Answer: (D) as the last reading from a setup, to find the level of a new point

The fore sight is the final reading from a setup, usually on a turning point, giving its level.

Question 8

An intermediate sight (IS) in levelling is

  1. a reading taken on a turning point between two setups
  2. the last reading taken from a setup before the instrument is shifted
  3. any staff reading taken between the back sight and the fore sight from the same setup
  4. the first reading taken after the instrument has been set up and levelled
Show answer & solution

Answer: (C) any staff reading taken between the back sight and the fore sight from the same setup

Intermediate sights are extra readings on points whose levels are needed, taken from the same instrument position.

Question 9

A turning point (change point) in levelling is a point

  1. of known elevation, used to check the closing of the work at the end of each day
  2. at which the instrument is set up for the first time
  3. on which only intermediate sights are taken from the same setup
  4. on which a fore sight from one setup and a back sight from the next are taken
Show answer & solution

Answer: (D) on which a fore sight from one setup and a back sight from the next are taken

Turning points carry the levelling forward from one instrument position to the next.

Question 10

In the height of instrument (collimation) method of levelling, the reduced levels are found by

  1. adding the BS to the RL of the bench mark to get the HI, then subtracting other readings from it
  2. subtracting the BS from the RL of the bench mark to get the HI, then adding each other reading
  3. adding the rise or subtracting the fall between consecutive readings to the preceding reduced level
  4. adding each staff reading to the reduced level of the preceding point in turn
Show answer & solution

Answer: (A) adding the BS to the RL of the bench mark to get the HI, then subtracting other readings from it

The height of instrument is the known RL plus the back sight, and the RL of any other point is the HI minus its staff reading.

Question 11

In the rise and fall method of levelling, the reduced level of a point is found by

  1. subtracting each staff reading from the height of collimation of the setup concerned, point by point
  2. taking the difference between the first and last readings of each setup only
  3. adding all the back sights to the RL of the bench mark and subtracting the fore sights
  4. comparing consecutive staff readings and adding the rise to, or subtracting the fall from, the preceding RL
Show answer & solution

Answer: (D) comparing consecutive staff readings and adding the rise to, or subtracting the fall from, the preceding RL

Each reading is compared with the previous one, and the difference shows whether the ground rises or falls.

Question 12

Compared with the rise and fall method, the height of instrument method of levelling

  1. gives a check on the back sights and fore sights, but not on the intermediate sights
  2. gives no check on the arithmetic of any reading
  3. involves more calculation when many intermediate sights are taken
  4. gives a check on the intermediate sights, but not on the back sights and fore sights
Show answer & solution

Answer: (A) gives a check on the back sights and fore sights, but not on the intermediate sights

In the HI method only ΣBS − ΣFS = last RL − first RL can be checked, so errors in intermediate RLs are not detected.

Question 13

Because of the curvature of the earth, a staff reading taken on a distant point with a horizontal line of sight is

  1. greater than the true reading, so the curvature correction is added to the reading
  2. smaller than the true reading, so the curvature correction is added to the reading
  3. greater than the true reading, so the curvature correction is subtracted from the reading
  4. unaffected, because the level surface and the line of sight coincide
Show answer & solution

Answer: (C) greater than the true reading, so the curvature correction is subtracted from the reading

The level surface falls away below the horizontal line of sight, so the staff reads too much and the point appears lower than it is.

Question 14

Atmospheric refraction in levelling

  1. bends the line of sight away from the earth, so adding to the effect of curvature
  2. bends the line of sight towards the earth, partly offsetting the effect of curvature
  3. has no effect on levelling because the line of sight is horizontal
  4. shifts the line of sight sideways without changing the staff readings
Show answer & solution

Answer: (B) bends the line of sight towards the earth, partly offsetting the effect of curvature

Refraction curves the ray slightly downward, so it reduces the curvature effect by about one-seventh.

Question 15

The combined correction for curvature and refraction, in metres, for a sight of D kilometres is

  1. 0.0112 D²
  2. 0.0673 D²
  3. 0.0785 D²
  4. 0.0897 D²
Show answer & solution

Answer: (B) 0.0673 D²

Curvature is 0.0785 D² and refraction is 0.0112 D² in the opposite sense, so the combined value is 0.0673 D², which is 6/7 of the curvature correction.

Question 16

Reciprocal levelling is carried out to

  1. determine the height of an inaccessible tower or chimney from two instrument stations on the ground
  2. measure the sensitivity of the bubble tube of a level by tilting it
  3. check the closing error of a level circuit by returning to the starting bench mark
  4. eliminate collimation, curvature and refraction errors when levelling across a river
Show answer & solution

Answer: (D) eliminate collimation, curvature and refraction errors when levelling across a river

Observing from each bank makes the errors act equally in opposite directions, so the mean of the two differences removes them.

Question 17

Profile (longitudinal) levelling is carried out to

  1. obtain the elevations of points at the corners of grid squares laid out for contouring
  2. determine the elevations of bench marks by double levelling in the forward and reverse directions
  3. obtain the elevations of points along a fixed line such as the centreline of a road, canal or pipeline
  4. obtain ground levels at right angles to the centreline at each station
Show answer & solution

Answer: (C) obtain the elevations of points along a fixed line such as the centreline of a road, canal or pipeline

A profile shows the ground elevation along the route, which is needed to design grades.

Question 18

Cross-sectional levelling along the centreline of a proposed road is carried out to

  1. fix the chainage of the points along the centreline of the proposed road alignment
  2. check the profile levels by running them again in the reverse direction
  3. obtain ground levels at right angles to the centreline at intervals, for estimating earthwork
  4. carry the bench mark levels across a river or a wide canal
Show answer & solution

Answer: (C) obtain ground levels at right angles to the centreline at intervals, for estimating earthwork

Cross sections show the shape of the ground across the route, giving the areas used for cut and fill volumes.

Question 19

Contour lines on a map are lines joining points that have

  1. the same elevation above a chosen datum
  2. the same horizontal distance from a reference line
  3. the same distance from the nearest bench mark
  4. the same slope of ground
Show answer & solution

Answer: (A) the same elevation above a chosen datum

A contour is a line of constant elevation and shows the shape of the terrain.

Question 20

The vertical distance between two consecutive contour lines is called the

  1. horizontal equivalent
  2. gradient
  3. contour interval
  4. relief
Show answer & solution

Answer: (C) contour interval

Contour interval is the constant difference in elevation between adjacent contours of a map.

Question 21

The horizontal distance on the map between two adjacent contour lines is called the

  1. horizontal equivalent
  2. relief of the area
  3. contour interval of the map
  4. gradient of the slope
Show answer & solution

Answer: (A) horizontal equivalent

The horizontal equivalent varies with the steepness of the slope, being small on steep ground and large on flat ground.

Question 22

Closely spaced contour lines on a map indicate

  1. a gentle, uniform slope of the ground
  2. a flat plain with little relief
  3. a steep slope of the ground
  4. a ridge line running along the crest of a hill
Show answer & solution

Answer: (C) a steep slope of the ground

Closely spaced contours mean that the elevation changes rapidly over a short horizontal distance.

Question 23

Contour lines that are widely and equally spaced indicate

  1. a vertical cliff
  2. a slope that becomes steeper downhill
  3. a steep, uniform slope
  4. a gentle, uniform slope
Show answer & solution

Answer: (D) a gentle, uniform slope

A wide horizontal equivalent for a constant interval means a flat slope, and equal spacing means that it is uniform.

Question 24

In the direct method of contouring,

  1. points lying on the required contour are located in the field by levelling and then surveyed
  2. contours are traced from aerial photographs without any levelling on the ground
  3. spot levels are plotted along cross sections and equal levels are joined
  4. levels are observed on a grid and the contours are interpolated later in the office
Show answer & solution

Answer: (A) points lying on the required contour are located in the field by levelling and then surveyed

In the direct method the staff is held at a predetermined reading, so the points found are already at the contour elevation.

Question 25

In the indirect method of contouring,

  1. points lying exactly on each contour are found by levelling and then located on the ground
  2. the contour points are plotted from the plane table by intersection, without any levelling
  3. contours are traced on the ground by a clinometer held at a constant angle
  4. levels are taken at grid points or along lines, and contours are interpolated
Show answer & solution

Answer: (D) levels are taken at grid points or along lines, and contours are interpolated

The indirect method surveys convenient points, and contour positions are found by interpolation afterwards.

Question 26

The temporary adjustments of a level, made at every setup, consist of

  1. making the axis of the bubble tube perpendicular to the vertical axis
  2. setting up the instrument, levelling it up and eliminating parallax
  3. making the line of collimation parallel to the axis of the bubble tube
  4. making the horizontal cross hair perpendicular to the vertical axis
Show answer & solution

Answer: (B) setting up the instrument, levelling it up and eliminating parallax

Setting up, levelling and focusing are repeated at each station, while the other adjustments are permanent adjustments.

Question 27

In a dumpy level, the telescope is

  1. kept horizontal automatically by a compensator
  2. carried in Y-shaped supports so that it can be lifted out and reversed end for end
  3. carried on a tilting screw so that it can be inclined to the line of sight
  4. rigidly fixed to the vertical spindle and cannot be reversed end for end
Show answer & solution

Answer: (D) rigidly fixed to the vertical spindle and cannot be reversed end for end

The dumpy level is simple and stable because its telescope is permanently fixed to its support.

Question 28

The telescope of a Y-level (wye level) is

  1. supported in Y-shaped bearings, so that it can be lifted out, rotated and reversed
  2. kept level by a pendulum compensator after rough levelling
  3. tilted by a micrometer screw for each reading
  4. permanently fixed to the vertical spindle and cannot be lifted out or reversed
Show answer & solution

Answer: (A) supported in Y-shaped bearings, so that it can be lifted out, rotated and reversed

The Y-level's telescope rests in clips on Y-supports, which makes it easy to test and adjust by reversal.

Question 29

An automatic (self-levelling) level has a compensator that

  1. records staff readings by electronic scanning of the staff
  2. keeps the line of sight horizontal once the instrument is roughly levelled with a circular bubble
  3. levels the instrument on its tripod head without the use of any foot screws or bubble
  4. computes the reduced levels from the readings
Show answer & solution

Answer: (B) keeps the line of sight horizontal once the instrument is roughly levelled with a circular bubble

The compensator corrects small residual tilts of the instrument, so no tubular bubble has to be centred before each reading.

Question 30

A digital level

  1. needs no tripod because it is held by hand
  2. reads a bar-coded staff electronically and records the reading, reducing reading and booking errors
  3. measures levels without a staff, by laser reflection from the ground surface itself
  4. measures horizontal and vertical angles by electronic circles
Show answer & solution

Answer: (B) reads a bar-coded staff electronically and records the reading, reducing reading and booking errors

Digital levels read a coded staff by image processing and store the data, which removes most human errors.

Question 31

The sensitivity of a bubble tube is expressed as

  1. the number of divisions engraved on the tube
  2. the time taken for the bubble to settle
  3. the length of the bubble, in divisions, at standard temperature
  4. the angular value of one division of the bubble tube scale
Show answer & solution

Answer: (D) the angular value of one division of the bubble tube scale

Sensitivity is the angle through which the axis of the tube must be tilted to move the bubble by one division.

Question 32

A more sensitive bubble tube, that is one with a smaller angular value per division, gives

  1. less precise levelling, because the bubble then moves too little for a given tilt
  2. the same precision, since the staff reading controls the result
  3. a line of sight that is horizontal without using the foot screws
  4. more precise levelling, although the bubble takes longer to centre
Show answer & solution

Answer: (D) more precise levelling, although the bubble takes longer to centre

A small tilt moves a sensitive bubble through a visible distance, so the line of sight can be set more accurately.

Question 33

The two-peg test of a level is made to

  1. check the graduation and length of the levelling staff in use
  2. determine the curvature and refraction correction for the site
  3. test and correct the collimation error of the instrument
  4. find the angular value of one division of the bubble tube
Show answer & solution

Answer: (C) test and correct the collimation error of the instrument

Readings from the middle and from one end of a line between two pegs show whether the line of sight is inclined.

Question 34

If a level has a collimation error that cannot be adjusted immediately, accurate levelling can still be done by

  1. setting the instrument nearer to the back sight than to the fore sight
  2. reading each staff twice and rejecting the larger reading
  3. keeping the back sight and fore sight distances equal at each setup
  4. doubling the length of each sight
Show answer & solution

Answer: (C) keeping the back sight and fore sight distances equal at each setup

With equal sight lengths, the error in the back sight and fore sight is the same and cancels in the difference.

Question 35

Parallax in the telescope of a level occurs when

  1. the line of sight is not truly horizontal when the bubble is central in its tube
  2. the staff is not held vertical on the point
  3. the bubble moves when the eye-piece is turned or focused
  4. the image of the staff does not fall on the plane of the cross hairs
Show answer & solution

Answer: (D) the image of the staff does not fall on the plane of the cross hairs

When the image and the cross hairs are in different planes, the cross hairs appear to move over the staff as the eye moves.

Question 36

Parallax in the telescope is eliminated by

  1. using a longer staff held closer to the instrument for each reading
  2. focusing the eye-piece on the cross hairs and then the object glass on the staff
  3. turning the diaphragm adjusting screws until the hairs look sharp
  4. levelling up the instrument again carefully with the foot screws at the same station
Show answer & solution

Answer: (B) focusing the eye-piece on the cross hairs and then the object glass on the staff

Focusing the eye-piece first and then the object glass brings the image into the plane of the cross hairs.

Question 37

A laser level used on construction sites works by projecting

  1. satellite signals from which a receiver computes its elevation above the datum
  2. a magnetic field that forms a level plane, detected by a compass needle placed in the field
  3. a rotating or fixed beam that forms a level line or plane, picked up by a detector or seen directly
  4. an ultrasonic pulse that is timed on reflection from a staff
Show answer & solution

Answer: (C) a rotating or fixed beam that forms a level line or plane, picked up by a detector or seen directly

The beam gives a visible or detectable reference line or plane for levelling and alignment.

Question 38

Plane table surveying is a method in which

  1. the map is prepared from overlapping air photographs
  2. fieldwork and plotting of the map are done together on the spot
  3. only vertical angles are measured on the ground
  4. the plotting is done in the office from angles booked in the field
Show answer & solution

Answer: (B) fieldwork and plotting of the map are done together on the spot

The map is drawn directly in the field, so omissions can be noticed while the ground is still in view.

Question 39

In the radiation method of plane tabling,

  1. rays are drawn from one table station to the points, which are plotted along them at scaled distances
  2. points are located by the intersection of rays drawn from two stations without measuring distances
  3. points are fixed by back rays drawn from three known stations
  4. the table is moved to successive stations along a route
Show answer & solution

Answer: (A) rays are drawn from one table station to the points, which are plotted along them at scaled distances

Radiation uses one set-up: the direction of each point is drawn and its distance measured and plotted to scale.

Question 40

In the intersection method of plane tabling, a point is located by

  1. moving the table along a route and plotting each station
  2. a ray drawn to it from one station, with its measured distance scaled along the ray
  3. the intersection of rays drawn to it from two stations, without measuring its distance
  4. the intersection of back rays drawn from known points to the plane table station
Show answer & solution

Answer: (C) the intersection of rays drawn to it from two stations, without measuring its distance

Intersection needs two well-placed rays from stations already plotted, and no distance to the point is required.

Question 41

The traversing method of plane tabling is used when

  1. all the points are located by rays and measured distances drawn from one table station
  2. the table is set up at successive stations along a route, each plotted from the last
  3. the table is oriented by back rays to distant peaks using the alidade
  4. the table is oriented by three known points marked on the sheet
Show answer & solution

Answer: (B) the table is set up at successive stations along a route, each plotted from the last

A plane table traverse proceeds station by station like a theodolite traverse, but the lines are plotted directly.

Question 42

A disadvantage of plane table surveying is that

  1. it requires a long field book as no plotting is done on the ground
  2. it is unsuitable for filling in the details between control points
  3. it cannot be used with a telescopic alidade
  4. it is affected by damp weather, which distorts the paper
Show answer & solution

Answer: (D) it is affected by damp weather, which distorts the paper

Paper is affected by rain and humidity, and errors may remain unnoticed until the plotted work is checked.

Question 43

The main purpose of orientation in plane table surveying is to

  1. determine the magnetic declination of the area with the trough compass
  2. make the lines on the paper parallel to the corresponding ground lines
  3. level the table horizontally using a spirit level on the board
  4. centre the table exactly over the ground station mark by means of a plumb bob
Show answer & solution

Answer: (B) make the lines on the paper parallel to the corresponding ground lines

Orientation turns the board until every drawn line is parallel to the ground line it represents, so that rays plot in the correct direction.

Practice these 43 questions interactively →