Tacheometry is a method of determining horizontal distances and elevations
by chaining along the ground and correcting each length for the slope
from phase comparison of reflected electromagnetic waves
from the angles of a triangulation network
indirectly from optical readings on a staff, without chaining the distances
Show answer & solution
Answer: (D) indirectly from optical readings on a staff, without chaining the distances
A tacheometer computes distance and height from the staff intercept and vertical angle, avoiding direct chaining.
Question 2
The two extra horizontal hairs (stadia hairs) in the diaphragm of a tacheometer are provided to
read the staff more easily to the nearest millimetre
measure the vertical angle to the staff more precisely
give the staff intercept from which the horizontal distance is computed
make the line of sight horizontal without using the bubble
Show answer & solution
Answer: (C) give the staff intercept from which the horizontal distance is computed
The difference between the readings of the upper and lower stadia hairs is the staff intercept used for distance.
Question 3
The multiplying and additive constants of a tacheometer are used in the formula connecting
the focal length, the aperture and the magnification of the objective
the vertical angle, the height of instrument and the reading at the top hair
the magnetic bearing, the line length and the declination
the horizontal distance, the staff intercept and the vertical angle
Show answer & solution
Answer: (D) the horizontal distance, the staff intercept and the vertical angle
The constants K and C appear in the standard distance formula with the staff intercept and the vertical angle.
Question 4
With the line of sight horizontal, the horizontal distance by the stadia method is D = K s + C, where s is
the staff intercept, K the multiplying constant and C the additive constant
the distance from the instrument to the stadia hairs, K the staff intercept and C the sum of readings
the vertical angle, K the focal length and C the aperture
the staff reading at the central hair, K the multiplying constant and C the height of instrument
Show answer & solution
Answer: (A) the staff intercept, K the multiplying constant and C the additive constant
The distance is proportional to the staff intercept s, plus a small constant C.
Question 5
For an inclined line of sight at vertical angle θ, with the staff held vertical, the horizontal distance by the stadia method is
D = K s cosθ + C
D = K s sin²θ + C sinθ
D = K s cos²θ + C cosθ
D = K s + C cosθ
Show answer & solution
Answer: (C) D = K s cos²θ + C cosθ
For an inclined sight the staff intercept is reduced by cosθ, so the distance is K s cos²θ + C cosθ.
Question 6
The additive constant of a modern internal-focusing tacheometer is
about 0.3 m, whereas it is nearly zero in external-focusing tacheometers
nearly zero, so that the distance is practically K times the staff intercept
about 100, so that it is the main term in the distance formula
equal to the multiplying constant
Show answer & solution
Answer: (B) nearly zero, so that the distance is practically K times the staff intercept
Internal focusing brings the additive constant close to zero, which simplifies the distance formula.
Question 7
The multiplying constant of a tacheometer is generally designed to be about
10
50
100
500
Show answer & solution
Answer: (C) 100
Instruments are generally made with K = 100, so that the distance is 100 times the staff intercept.
Question 8
In the movable hair method of tacheometry,
the hairs are moved by a micrometer until the intercept is a fixed known length
the stadia hairs are fixed and the staff intercept is read afresh for each distance
the instrument is moved along the line until the intercept equals the stadia interval
two vertical angles are read to targets on a staff of known length
Show answer & solution
Answer: (A) the hairs are moved by a micrometer until the intercept is a fixed known length
The hairs are moved until they coincide with fixed marks on the staff, and the distance follows from the hair movement.
Question 9
The tangential method of tacheometry determines distance from
two vertical angles to targets a known distance apart on a staff
the intercept between fixed stadia hairs on a staff held vertically
a magnetic bearing and one vertical angle
the horizontal angle subtended by a bar of known length
Show answer & solution
Answer: (A) two vertical angles to targets a known distance apart on a staff
The tangential method uses two vertical angles and the known staff target spacing, and needs no stadia hairs.
Question 10
The main advantage of tacheometry over direct chaining is that it is
more accurate than chaining on every kind of ground and over every length
much faster, especially for detail work on rough ground
free from the need for a staff or a vertical angle
usable only on level ground, with no vertical angles
Show answer & solution
Answer: (B) much faster, especially for detail work on rough ground
Distances are computed from readings, so rough ground that makes chaining slow does not delay the work.
Question 11
In stadia tacheometry, the elevation of a staff station is computed from the horizontal distance, the vertical angle, the height of the instrument axis and the
difference between the upper and lower hair readings
reading of the central (axial) hair on the staff
reading of the lower stadia hair alone
reading of the upper stadia hair alone
Show answer & solution
Answer: (B) reading of the central (axial) hair on the staff
RL of staff point = RL of instrument station + height of axis + D tanθ − central hair reading.
Question 12
A subtense bar is used with a theodolite to determine distance by
timing a light pulse to the bar and back with a counter
measuring the horizontal angle subtended by the bar of known length and computing the distance
reading the stadia intercept on the bar through the telescope of the theodolite
measuring the vertical angles to the top and bottom of the bar held on the ground
Show answer & solution
Answer: (B) measuring the horizontal angle subtended by the bar of known length and computing the distance
With the bar length b and subtended angle α, the distance is D = (b/2) cot(α/2).
Question 13
Compared with electronic distance measurement, tacheometry is
more precise over long lines and in all kinds of terrain
equal in precision and speed on all kinds of work
less precise, but quick and suitable for detail work
unable to give horizontal distances without a chained check line
Show answer & solution
Answer: (C) less precise, but quick and suitable for detail work
Tacheometry remains useful for fast detail work, though EDM is more accurate for single distances.
Question 14
Simpson's rule for the area of an irregular boundary requires that the offsets are taken
at any number of equal intervals, not more than 10 m apart
at equal intervals, with an odd number of offsets (an even number of intervals)
at equal intervals, with an even number of offsets (an odd number of intervals)
at unequal intervals chosen at the breaks of the boundary
Show answer & solution
Answer: (B) at equal intervals, with an odd number of offsets (an even number of intervals)
The rule fits parabolas to successive pairs of strips, so the strips must be equal and even in number.
Question 15
The trapezoidal rule for the area from offsets assumes that the boundary between successive offsets is
a circular arc between the offsets
a parabola through three successive offsets
a straight line parallel to the base line at the mean offset
a straight line joining the tops of the offsets
Show answer & solution
Answer: (D) a straight line joining the tops of the offsets
The area of each strip is taken as the mean of its two offsets times the interval.
Question 16
The volume of earthwork in a cutting or embankment is computed from the cross-sectional areas at regular intervals using
the trapezoidal or the prismoidal formula along the alignment
the longitudinal gradient of the alignment alone
the plan area of the site multiplied by the mean depth of the ground
the area of the longitudinal section multiplied by the formation width
Show answer & solution
Answer: (A) the trapezoidal or the prismoidal formula along the alignment
Volume between sections is found from the mean of the end areas (trapezoidal) or by the prismoidal formula.
Question 17
Triangulation is a surveying method used mainly to
survey a small plot of land by offsets from a base line across the plot
establish elevations of points along a route by a series of height differences
establish accurate control over a large area from the angles of a triangle network
fix detail points directly by chain and offsets from a few base lines on the ground
Show answer & solution
Answer: (C) establish accurate control over a large area from the angles of a triangle network
Triangulation builds control over a large area from observed angles, scaled by a baseline.
Question 18
The baseline of a triangulation network is
a line measured with an ordinary chain on convenient level ground near the base
the shortest side of the network, whose length is assumed from the map scale
a side measured very precisely, from which the other sides are computed from the angles
the line joining the first and last stations, whose length is scaled from the available topographic map
Show answer & solution
Answer: (C) a side measured very precisely, from which the other sides are computed from the angles
The baseline fixes the scale of the network, so it is measured with great care.
Question 19
In trilateration, the quantities measured in the field are
the elevations of the stations, by levelling
the angles at each station, by theodolite
the lengths of the sides of the triangles, usually by EDM
the azimuths of the sides of the triangles, by astronomical observation
Show answer & solution
Answer: (C) the lengths of the sides of the triangles, usually by EDM
Trilateration fixes the stations from measured side lengths, unlike triangulation which relies on angles.
Question 20
Triangulation is classified into orders as
first, second and third order, with precision and station spacing decreasing from first to third
short-base and long-base triangulation, according to the baseline length alone
primary, secondary and tertiary, with precision increasing from primary to tertiary
compass, theodolite and plane table triangulation, according to the instrument used
Show answer & solution
Answer: (A) first, second and third order, with precision and station spacing decreasing from first to third
First-order work has the highest precision and longest lines; lower orders are densified within it.
Question 21
First-order triangulation is used mainly to provide
the national geodetic control framework, to which lower-order surveys and mapping are tied
the contour and detail survey of a small plot of land within an urban area
the layout of a large building on a single construction site, with its axes
the levels along a canal section for the design of its bed
Show answer & solution
Answer: (A) the national geodetic control framework, to which lower-order surveys and mapping are tied
It is the highest-precision backbone, from which second- and third-order control and the mapping are derived.
Question 22
A chain of triangles in triangulation is suited to
the detailed mapping of urban areas with a very dense street pattern
a wide area of roughly square or circular shape with stations all round
a long, narrow strip of country, such as along a valley or coast
a short extension of the measured baseline to a second station
Show answer & solution
Answer: (C) a long, narrow strip of country, such as along a valley or coast
A single chain extends in one direction, so it fits long narrow areas.
Question 23
Compared with a simple chain of single triangles, a chain of braced quadrilaterals provides
fewer checks and weaker geometry, but quicker and cheaper observation
more redundant observations and checks, and so greater strength
a network that cannot be adjusted by least squares
the same strength, with half as many stations
Show answer & solution
Answer: (B) more redundant observations and checks, and so greater strength
The diagonals in each quadrilateral give extra conditions, so the figure is stronger and can be checked.
Question 24
The satellite (false) station technique in triangulation involves
omitting the station and using the remaining stations
occupying a nearby point and correcting the angles to reduce them to the true station
using a tower to raise the signal above the obstructions
occupying a station established by GPS in place of the original triangulation station
Show answer & solution
Answer: (B) occupying a nearby point and correcting the angles to reduce them to the true station
The small offset is measured and the observed directions are corrected as if observed at the true station centre.
Question 25
The strength of a triangulation figure is assessed to
decide how many rounds of angles are to be observed at each station
find how well a figure limits the build-up of error in computed lengths
determine the length of baseline that is required for the network
check that the angles of each triangle of the figure add up to 180° within limits
Show answer & solution
Answer: (B) find how well a figure limits the build-up of error in computed lengths
Strength of figure measures how error propagates through the network, which guides the choice of the best layout.
Question 26
Reconnaissance in a triangulation survey is
a preliminary field inspection to select suitable station sites
the adjustment of the network in the office
the measurement of the baseline with invar tapes
the final observation of the angles to the highest possible precision
Show answer & solution
Answer: (A) a preliminary field inspection to select suitable station sites
Reconnaissance is done first, to select stations before detailed observations are begun.
Question 27
Intervisibility between triangulation stations is checked mainly by
assuming that all stations stand 10 m above the surrounding ground
reconnaissance, and computations from heights, distances and the ground profile
observing all the stations from one end of the baseline only, with a theodolite
levelling between adjacent stations to find their height differences
Show answer & solution
Answer: (B) reconnaissance, and computations from heights, distances and the ground profile
Long lines must clear the intervening ground after curvature and refraction are allowed for, so this is checked in advance.
Question 28
A tower or scaffold is built over a triangulation station mainly to
bring the neighbouring stations closer together in the network
make the station mark permanent so that it can be used for later surveys
avoid the need for a signal at the station when the lines are long
raise the instrument above obstructions such as trees to give the required line of sight
Show answer & solution
Answer: (D) raise the instrument above obstructions such as trees to give the required line of sight
Raising the instrument and signal above obstructions makes the neighbouring stations intervisible.
Question 29
Trilateration became widespread mainly because of
the adoption of the metric chain for field work
the invention of the plane table for field mapping
the introduction of the invar tape for baseline measurement
the development of reliable, portable EDM instruments
Show answer & solution
Answer: (D) the development of reliable, portable EDM instruments
Accurate and economical measurement of long lines by EDM made trilateration practical.
Question 30
A total station combines an electronic theodolite with
a magnetic compass and a stadia diaphragm
a GNSS receiver and a barometric altimeter
an automatic level and a plumb bob for centring over the station
an EDM and a microprocessor for computing and storing data
Show answer & solution
Answer: (D) an EDM and a microprocessor for computing and storing data
A total station measures angles and distances electronically and computes coordinates in one instrument.
Question 31
An EDM instrument determines distance by measuring
the time or phase delay of a signal sent to a reflector and back
the angle subtended at the instrument by a bar of known length
the pull required to hold a calibrated invar tape straight
the intercept between the stadia hairs on a vertical levelling staff
Show answer & solution
Answer: (A) the time or phase delay of a signal sent to a reflector and back
Distance is obtained from the time or phase delay of the returned infrared or laser signal and the known speed of the wave.
Question 32
A prism (reflector) is placed at the target when using an EDM because it
keeps the instrument levelled automatically while it measures
magnifies the target for sighting by eye at long range
supplies the instrument with GNSS time signals needed for the distance measurement
reflects the signal back to the instrument for the distance measurement
Show answer & solution
Answer: (D) reflects the signal back to the instrument for the distance measurement
The retroreflector returns the signal along its path of arrival to the instrument.
Question 33
A reflectorless total station can
operate only at night, when surfaces are dark
measure distance only when the target is lit by a laser pointer
measure distance to prisms only, but at much longer range
measure distance directly to natural surfaces such as a wall or rock, without a prism
Show answer & solution
Answer: (D) measure distance directly to natural surfaces such as a wall or rock, without a prism
The instrument uses the diffuse reflection of the laser from the surface, so no prism is needed.
Question 34
GPS and other GNSS surveying determine the position of a receiver by
comparing the atmospheric pressure at ground stations
reading a magnetic bearing and a distance
measuring signal travel times from several satellites of known position
sighting the satellites with a theodolite and measuring their angles of elevation
Show answer & solution
Answer: (C) measuring signal travel times from several satellites of known position
Timing of satellite signals gives distances to satellites, from which the receiver position is computed.
Question 35
At least how many satellites must be tracked by a GPS receiver to fix a three-dimensional position?
1
2
3
4
Show answer & solution
Answer: (D) 4
Four satellites are needed to solve for three position coordinates and the receiver clock error.
Question 36
Differential GPS and RTK techniques are used to
measure heights above the datum only, not positions
improve accuracy (sub-metre with DGPS, centimetre level with RTK) using corrections from a reference station of known position
reduce signal errors by using only satellites at low elevation angles in the sky above the horizon
give a position without using satellite signals, by ground beacons
Show answer & solution
Answer: (B) improve accuracy (sub-metre with DGPS, centimetre level with RTK) using corrections from a reference station of known position
Errors common to the base and rover receivers are removed by applying the base-station corrections.
Question 37
Remote sensing, as applied to mapping, is the
determination of bearings by a compass at each station of the traverse
measurement of heights with a level and staff on the ground
fixing of positions by chaining and offsets measured directly on the ground by the survey party
collection of data about the ground from a distance by satellite or airborne sensors
Show answer & solution
Answer: (D) collection of data about the ground from a distance by satellite or airborne sensors
Remote sensors record the reflected or emitted energy from the ground without contact.
Question 38
A Geographic Information System (GIS) is used mainly to
measure horizontal and vertical angles in the field with graduated circles
transmit differential corrections to survey receivers
determine distances by timing laser pulses
capture, store, analyse and display spatially referenced data
Show answer & solution
Answer: (D) capture, store, analyse and display spatially referenced data
A GIS manages and analyses geographic data, such as maps and attributes, in layers.
Question 39
Photogrammetry is the science of obtaining reliable measurements from
photographs, aerial or terrestrial
ranging signals from satellites
echo soundings of the bed of a water body
latitudes and departures of a traverse
Show answer & solution
Answer: (A) photographs, aerial or terrestrial
Photogrammetry derives measurements and maps by recording, measuring and interpreting photographic images.
Question 40
Successive aerial photographs are taken with an overlap so as to
allow stereoscopic viewing and 3D measurement from pairs of photographs
remove the need for any ground control points in the mapped area
reduce the number of photographs needed to cover the whole area to be mapped
allow the camera to be used without any calibration of its lens
Show answer & solution
Answer: (A) allow stereoscopic viewing and 3D measurement from pairs of photographs
Overlapping pairs give two views of the same ground, from which heights can be measured.
Question 41
A robotic (motorised) total station can
measure distance without any reflector or prism, to any natural surface in range
be used without a tripod, by holding it in the hand
track and follow a moving prism automatically, so that one surveyor can do the work of a crew
locate buried pipes and cables by ground-penetrating radar
Show answer & solution
Answer: (C) track and follow a moving prism automatically, so that one surveyor can do the work of a crew
A servo-driven instrument locks on to the prism, so one person can set out or survey while holding the prism.
Question 42
Drones (UAVs) with cameras or sensors are used in modern surveying mainly for
rapid aerial photogrammetric mapping, giving terrain models and orthophotos
high-precision control of bench marks, replacing the need for any ground control