Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Surveying: Linear Measurements, Chaining and Compass Surveying

Civil Engineering · Surveying

42 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Chain surveying is mainly suited to

  1. extensive areas that need a geodetic framework of accurate control
  2. areas where angular accuracy is of prime importance for the work
  3. fairly level, open ground with few obstructions and a small area
  4. hilly, wooded terrain with many obstructions to measurement and chaining
Show answer & solution

Answer: (C) fairly level, open ground with few obstructions and a small area

Chain surveying uses linear measurements only, so it works best on open, level ground over small areas.

Question 2

A metric surveyor's chain is made of

  1. woven linen fabric reinforced with fine brass wires
  2. brass rods joined by hinges and screw clamps at each end
  3. invar strips welded end to end with brass handles
  4. galvanised mild steel wire links joined by rings
Show answer & solution

Answer: (D) galvanised mild steel wire links joined by rings

Chain links of galvanised mild steel wire are joined by small rings, giving a strong and flexible field chain of known length.

Question 3

Compared with a chain, a steel tape is

  1. equally accurate, because each is made of steel
  2. less accurate, but more rugged in rough field use
  3. less accurate and also more easily damaged
  4. more accurate, but more easily damaged and kinked
Show answer & solution

Answer: (D) more accurate, but more easily damaged and kinked

A steel tape has no joints to wear and gives better accuracy, but it needs careful handling.

Question 4

Ranging in chain surveying means

  1. fixing intermediate points on the straight line between two end stations
  2. measuring perpendicular offsets from the chain line to the nearby details to be plotted
  3. measuring the included angle between adjacent chain lines at the station
  4. levelling the ground along the chain line to find its slope
Show answer & solution

Answer: (A) fixing intermediate points on the straight line between two end stations

Ranging places intermediate ranging rods in line so that the chain can be laid straight between the end stations.

Question 5

Direct ranging of a survey line is carried out when

  1. the line crosses a stream and must be ranged by reciprocal observations
  2. the end stations are visible from each other
  3. a rise in the ground hides one end station from the other
  4. the line is to be set at right angles to another line
Show answer & solution

Answer: (B) the end stations are visible from each other

Direct ranging is possible only when the end stations can be seen from the intermediate points.

Question 6

Indirect (reciprocal) ranging is adopted when

  1. the ground is flat and the end stations are visible from each other along the line
  2. the line is very short but is crossed by a belt of tall standing crops and bushes
  3. the line has to be measured on steeply sloping ground with frequent changes of gradient
  4. the end stations are not visible from each other, for example because a hill lies between them
Show answer & solution

Answer: (D) the end stations are not visible from each other, for example because a hill lies between them

When an obstruction blocks the view between the end stations, intermediate points are fixed by reciprocal observation.

Question 7

An offset in chain surveying is

  1. a lateral measurement from the chain line to a feature that is to be plotted
  2. the difference between the true length and the nominal length of a chain, per chain length
  3. the distance between the two ends of a chain line, taken along the line
  4. the angle between a chain line and the meridian, measured with a compass
Show answer & solution

Answer: (A) a lateral measurement from the chain line to a feature that is to be plotted

Offsets are short side measurements from the chain line, used to locate nearby details.

Question 8

A perpendicular offset is one that is

  1. measured at right angles to the chain line
  2. measured along the chain line from the starting station
  3. measured parallel to the chain line from the nearest station
  4. measured at any convenient angle and recorded with that angle
Show answer & solution

Answer: (A) measured at right angles to the chain line

A perpendicular offset is taken at 90° to the chain line, usually set with a cross staff or optical square.

Question 9

An oblique offset is one that is

  1. taken from the end of one chain line to the start of the next
  2. measured parallel to the chain line to a nearby station
  3. measured at exactly 90° to the chain line with the help of a cross staff or optical square
  4. measured at an angle other than a right angle, and fixed by its length and angle or by ties
Show answer & solution

Answer: (D) measured at an angle other than a right angle, and fixed by its length and angle or by ties

Oblique offsets are taken at some other angle, and the point is fixed by additional measurements such as ties.

Question 10

A well-conditioned triangle in chain surveying is one in which

  1. every angle lies between about 10° and 160°
  2. every angle lies between about 45° and 75°
  3. every angle is less than 90°
  4. every angle lies between about 30° and 120°
Show answer & solution

Answer: (D) every angle lies between about 30° and 120°

Avoiding very acute or very obtuse angles keeps plotting errors from being magnified.

Question 11

A cross staff, an optical square and a prism square are used to

  1. measure vertical angles up to about 45°
  2. measure the slope of the ground along a chain line
  3. set out right angles for perpendicular offsets
  4. read the magnetic bearings of chain lines
Show answer & solution

Answer: (C) set out right angles for perpendicular offsets

These simple instruments let the chainman fix the foot of a perpendicular from a point to the chain line.

Question 12

An error in chaining due to an incorrect length of the chain is

  1. a blunder, which will be detected by measuring a check line across the area
  2. a random error, since it is positive and negative in turn over the line
  3. a systematic error, since it repeats with every chain length laid down
  4. a negligible error, since it cancels out when the traverse is closed on itself
Show answer & solution

Answer: (C) a systematic error, since it repeats with every chain length laid down

A chain of wrong length makes the same error with every length laid down, so it accumulates along the line.

Question 13

A chain that is found to be longer than its nominal length gives a recorded distance that is

  1. greater than the true distance, so the correction is subtracted
  2. less than the true distance, so the correction is added
  3. greater than the true distance, so the correction is added
  4. less than the true distance, so the correction is subtracted
Show answer & solution

Answer: (B) less than the true distance, so the correction is added

Each chain length laid down covers more ground than recorded, so the recorded distance is too small and a positive correction is needed.

Question 14

A sag correction to a taped distance is required when the tape is

  1. held along a steep slope with its two ends at different heights
  2. stretched on the ground along its whole length and pulled to the standard tension
  3. pulled with a tension greater than its standard pull
  4. supported only at its ends or at a few points, so that it hangs in a curve
Show answer & solution

Answer: (D) supported only at its ends or at a few points, so that it hangs in a curve

An unsupported tape hangs in a catenary, so its ends are closer than the marked length and the correction is subtracted.

Question 15

Metric surveyor's chains most commonly used in the field have lengths of

  1. 1 m or 2 m
  2. 20 m or 30 m
  3. 50 m or 75 m
  4. 100 m or 200 m
Show answer & solution

Answer: (B) 20 m or 30 m

Metric chains are made mainly in 20 m and 30 m lengths for general field use.

Question 16

A metallic tape differs from a steel tape in that it is made of

  1. a single strip of invar with a very low coefficient of expansion
  2. glass-fibre cloth coated with PVC
  3. linen or other fabric reinforced with fine brass or copper wires
  4. high-carbon spring steel with etched graduations
Show answer & solution

Answer: (C) linen or other fabric reinforced with fine brass or copper wires

A metallic tape has a woven fabric base with fine metal wire, so it is lighter but less accurate than a steel tape.

Question 17

An invar tape is used for precise baseline measurement mainly because it has

  1. a very low coefficient of thermal expansion
  2. a very high tensile strength, so a large pull can be applied
  3. a low weight, which removes the need for a sag correction
  4. a high elasticity, which removes the need for a pull correction
Show answer & solution

Answer: (A) a very low coefficient of thermal expansion

Invar, an alloy of nickel and steel, changes length very little with temperature, so temperature error is minimal.

Question 18

Standardization of a chain or tape means

  1. comparing its actual length with a standard length to find the correction to be applied
  2. coating the tape with oil to prevent corrosion and to keep its length constant over time
  3. adding finer graduations to the tape, so that it can be read to a closer least count
  4. finding the pull at which the sag correction is equal and opposite to the pull correction
Show answer & solution

Answer: (A) comparing its actual length with a standard length to find the correction to be applied

Standardization determines the true length of the tape under standard conditions so that field readings can be corrected.

Question 19

A steel tape standardized at 20 °C is used in the field at 35 °C. The tape

  1. has contracted, so it reads more than the true distance and the correction is subtracted
  2. has contracted, so it reads less than the true distance and the correction is added
  3. has expanded, so it reads less than the true distance and the temperature correction is added
  4. has expanded, so it reads more than the true distance and the correction is subtracted
Show answer & solution

Answer: (C) has expanded, so it reads less than the true distance and the temperature correction is added

Steel expands when heated, so each tape length covers more ground than marked; the recorded distance is too small and the correction is positive.

Question 20

A pull (tension) correction is applied to a taped distance because

  1. the pull applied to the tape raises its temperature and so changes its length
  2. the tape has its standard length only at its standard pull, and a different field pull stretches or relaxes it
  3. a pull greater than the standard pull removes the sag completely but never changes the length of the tape
  4. the pull required to keep the tape horizontal depends on the gradient of the ground
Show answer & solution

Answer: (B) the tape has its standard length only at its standard pull, and a different field pull stretches or relaxes it

Under a pull greater than the standard pull the tape stretches and reads too little, while a smaller pull has the opposite effect.

Question 21

A slope correction is applied to a distance measured along inclined ground in order to

  1. reduce the effect of the sag of the tape between supports
  2. convert the slope distance into the equivalent horizontal distance
  3. convert the horizontal distance on the plan into the length along the ground
  4. allow for the stretching of the tape under the pull applied in the field
Show answer & solution

Answer: (B) convert the slope distance into the equivalent horizontal distance

Plans need horizontal distances, and a tape laid along a slope reads more than the horizontal, so the correction is subtracted.

Question 22

Which of the following is NOT a correction applied to a distance measured with a tape?

  1. sag correction for a tape supported at its ends
  2. correction for magnetic declination
  3. pull correction for a tape used at a non-standard tension
  4. slope correction for a line measured on inclined ground
Show answer & solution

Answer: (B) correction for magnetic declination

Temperature, pull, sag and slope corrections apply to tape measurement, whereas declination concerns the direction of lines in compass work.

Question 23

Compass surveying is the method in which

  1. the directions of lines are fixed by astronomical observations and the lengths measured by tacheometry on the ground
  2. the directions of lines are read from the horizontal circle of a theodolite set to true north
  3. the directions of lines are measured with a magnetic compass and their lengths by chain or tape
  4. the lengths of lines are measured by EDM and the directions by satellite signals
Show answer & solution

Answer: (C) the directions of lines are measured with a magnetic compass and their lengths by chain or tape

Compass surveying combines magnetic bearings of the survey lines with their measured lengths.

Question 24

In the whole circle bearing (WCB) system a bearing is measured

  1. from east, clockwise, from 0° to 180°
  2. from south, anticlockwise, from 0° to 360°
  3. from the nearer of north or south, between 0° and 90°
  4. from north, clockwise, from 0° to 360°
Show answer & solution

Answer: (D) from north, clockwise, from 0° to 360°

WCB gives a single value, clockwise from the north end of the meridian, between 0° and 360°.

Question 25

In the reduced (quadrantal) bearing system a bearing is measured

  1. clockwise from the north end of the meridian through 360°, with no quadrant letters
  2. from the nearer of north or south towards east or west, from 0° to 90°
  3. from the east-west line towards north or south, from 0° to 90°
  4. from true north towards east or west, from 0° to 180°
Show answer & solution

Answer: (B) from the nearer of north or south towards east or west, from 0° to 90°

Reduced bearings are stated as an acute angle from the north or south end of the meridian, with the quadrant letters, such as N 40° E.

Question 26

The fore bearing of a survey line is the bearing

  1. observed at the starting station, looking towards the forward station
  2. found by averaging the observations at each end of the line
  3. measured from true north instead of magnetic north
  4. observed at the forward station, looking back to the starting station
Show answer & solution

Answer: (A) observed at the starting station, looking towards the forward station

The fore bearing is the bearing of the line in the direction of progress of the survey.

Question 27

The back bearing of a survey line is the bearing

  1. of the next line of the traverse, observed at the same station
  2. measured anticlockwise from the south end of the meridian
  3. observed at the forward end of the line, looking back to the starting station
  4. observed at the starting station of the line, looking towards the forward station along it
Show answer & solution

Answer: (C) observed at the forward end of the line, looking back to the starting station

The back bearing is the reciprocal bearing, observed at the forward station of the line.

Question 28

In the absence of local attraction, the fore bearing and back bearing of a line differ by exactly

  1. 60°
  2. 90°
  3. 120°
  4. 180°
Show answer & solution

Answer: (D) 180°

The two directions of a line are opposite, so the bearings differ by 180°.

Question 29

Local attraction in compass surveying is the

  1. regular daily swing of the needle about its mean position, between morning and evening
  2. slow change of the magnetic declination at a place over a period of many years
  3. deflection of the needle from the magnetic meridian by iron objects or electric cables nearby
  4. tilting of the needle from the horizontal due to the vertical component of the earth's magnetic field
Show answer & solution

Answer: (C) deflection of the needle from the magnetic meridian by iron objects or electric cables nearby

Magnetic material near a station pulls the needle away from the meridian and gives a wrong bearing there.

Question 30

Local attraction at the stations of a compass traverse is detected by

  1. reading the dip of the needle at every station along the traverse
  2. comparing the sum of the interior angles of the traverse with (2n − 4) right angles
  3. checking whether the fore and back bearing of each line differ by exactly 180°
  4. chaining each line a second time in the reverse direction
Show answer & solution

Answer: (C) checking whether the fore and back bearing of each line differ by exactly 180°

If a line's fore and back bearings do not differ by 180°, the needle has been disturbed at one or more of its end stations.

Question 31

The magnetic declination at a place is the horizontal angle between

  1. the horizontal direction and the direction in which the needle dips
  2. the magnetic meridian and the survey line
  3. the true meridian and the survey line
  4. the true meridian and the magnetic meridian
Show answer & solution

Answer: (D) the true meridian and the magnetic meridian

Declination is the angle by which magnetic north differs from true north at a given place and time.

Question 32

If the fore bearing of a line is 36° 15′, its back bearing is

  1. 126° 15′
  2. 216° 15′
  3. 143° 45′
  4. 323° 45′
Show answer & solution

Answer: (B) 216° 15′

Since the fore bearing is less than 180°, back bearing = 36° 15′ + 180° = 216° 15′.

Question 33

A prismatic compass differs from a plain surveyor's compass in that it

  1. gives bearings referred to true north without any declination correction
  2. measures vertical angles as well as horizontal bearings, with a clinometer
  3. allows the object to be sighted and the bearing read at the same time
  4. reads bearings in the quadrantal system, from the nearer end of the meridian
Show answer & solution

Answer: (C) allows the object to be sighted and the bearing read at the same time

The prism lets the observer view the graduated card while sighting the object, which makes observation quicker.

Question 34

The graduations on the ring of a prismatic compass are

  1. marked in inverted form, with 0° at the south end and 180° at the north end
  2. numbered like a protractor, with 0° at the north end and 90° at the east end
  3. numbered anticlockwise from the east end of the card, with 0° at east
  4. marked from 0° to 90° in each of the four quadrants from the north and south ends
Show answer & solution

Answer: (A) marked in inverted form, with 0° at the south end and 180° at the north end

The ring stays fixed to the magnetic meridian while the body turns, so it is graduated in reverse to give the bearing of the line of sight.

Question 35

In a surveyor's (plain) compass the bearing is read

  1. through a prism fitted to the eye vane at the same moment as the object is sighted
  2. by looking down on the card through the glass top after sighting
  3. from a vernier that moves with the line of sight, to the nearest minute
  4. through a reading lens fitted to the object vane at the far end
Show answer & solution

Answer: (B) by looking down on the card through the glass top after sighting

Sighting is done through the vanes, and the bearing is then read from the card by looking down on it.

Question 36

The dip of the magnetic needle is the

  1. inclination of a freely suspended needle to the horizontal due to the earth's magnetic field
  2. horizontal angle between the true meridian and the magnetic meridian at the place
  3. horizontal deflection of the needle by iron objects or cables near the station
  4. slow change in the declination at the place over a period of many years
Show answer & solution

Answer: (A) inclination of a freely suspended needle to the horizontal due to the earth's magnetic field

Away from the magnetic equator the needle tends to tilt in a vertical plane, which is the dip.

Question 37

The dip of the needle in a compass is counteracted by

  1. a sliding brass rider on the north end of the needle in the northern hemisphere
  2. an extra pivot jewel placed at the north end of the needle
  3. a lead weight fixed at the centre of the needle
  4. a sliding brass rider on the south end of the needle in the northern hemisphere
Show answer & solution

Answer: (D) a sliding brass rider on the south end of the needle in the northern hemisphere

The north end of the needle dips in the northern hemisphere, so a small rider on the lighter south end balances it.

Question 38

The regular daily oscillation of the magnetic declination is called

  1. secular variation
  2. annual variation
  3. diurnal variation
  4. irregular variation
Show answer & solution

Answer: (C) diurnal variation

Diurnal variation is the regular daily swing of the declination, typically a few minutes of arc in amplitude.

Question 39

The secular variation of the magnetic declination is

  1. a slow change that continues in one sense over many years
  2. a regular daily swing of the needle, greater by day than at night
  3. a sudden and irregular change caused by a magnetic storm or earthquake
  4. a small oscillation of the declination that repeats every year
Show answer & solution

Answer: (A) a slow change that continues in one sense over many years

Secular variation is the slow, long-term drift of the magnetic meridian over years and decades.

Question 40

Irregular variation of the magnetic declination is caused by

  1. magnetic storms and similar disturbances that cannot be predicted
  2. iron objects and electric cables close to the station
  3. the slow movement of the magnetic poles
  4. the regular heating and cooling of the earth's surface by the sun every day
Show answer & solution

Answer: (A) magnetic storms and similar disturbances that cannot be predicted

Magnetic storms give sudden, unpredictable changes in declination, so no regular correction can be applied.

Question 41

To convert a magnetic bearing observed years ago into the present magnetic bearing, one must allow for

  1. the closing error of the old traverse
  2. the difference in chain length between the two surveys
  3. the change in the dip of the needle between the two dates
  4. the change in magnetic declination between the two dates
Show answer & solution

Answer: (D) the change in magnetic declination between the two dates

True bearings do not change, so old magnetic bearings are corrected by the change in declination since they were observed.

Question 42

A line is observed with a compass and its fore and back bearings differ by exactly 180°. This means that

  1. the declination at the two stations is exactly equal and zero
  2. local attraction is absent at the two stations, or has the same effect at each
  3. the traverse of which the line is part will close without any error
  4. the forward station is certainly free from local attraction while the rear station is affected
Show answer & solution

Answer: (B) local attraction is absent at the two stations, or has the same effect at each

Equal disturbance at the two ends changes the two bearings equally and the difference remains 180°, so this test alone cannot show it.

Practice these 42 questions interactively →