Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.
Question 1
Consumptive use of water by a crop is the water
- lost by deep percolation below the root zone of the crop after irrigation
- lost by transpiration of the plants and evaporation from adjoining soil
- lost as surface runoff from the field after a heavy irrigation
- applied at the field head, including all conveyance and application losses
Show answer & solution
Answer: (B) lost by transpiration of the plants and evaporation from adjoining soil
Consumptive use equals evapotranspiration of the cropped field.
Question 2
The net irrigation requirement (NIR) of a crop is its
- effective rainfall minus its consumptive use
- consumptive use minus the effective rainfall
- water diverted at the canal head to serve the field
- consumptive use plus canal conveyance losses
Show answer & solution
Answer: (B) consumptive use minus the effective rainfall
NIR is the field-level need left after effective rainfall has met part of the consumptive use.
Question 3
Effective rainfall in irrigation planning is the part of rainfall
- stored in the root zone and usable by the crop
- recorded by the rain gauge during the whole crop season
- percolating below the root zone to the water table
- lost as runoff from the field into the nearby drains
Show answer & solution
Answer: (A) stored in the root zone and usable by the crop
Only the fraction retained in the root zone meets crop water needs.
Question 4
The Penman (or Penman-Monteith) method is used to estimate
- potential evapotranspiration from temperature, humidity, wind and radiation
- duty of water computed from the canal discharge and the command area
- seepage loss from canals computed from soil permeability data and wetted perimeter
- peak flood discharge computed from rainfall and catchment data of the basin
Show answer & solution
Answer: (A) potential evapotranspiration from temperature, humidity, wind and radiation
Penman-type methods combine climatic variables to give reference evapotranspiration.
Question 5
Compared with the net irrigation requirement, the gross irrigation requirement (GIR) is
- equal, because the losses are excluded by definition of the term
- equal, because irrigation efficiency is assumed to be 100 per cent
- greater, as it also covers application and conveyance losses
- smaller, because water saved by mulching is deducted from it
Show answer & solution
Answer: (C) greater, as it also covers application and conveyance losses
GIR = NIR divided by the efficiency, so it always exceeds NIR.
Question 6
The intensity of irrigation in a canal command is the percentage of the
- total water available in the reservoir that is released to the canal
- culturable command area served by a single outlet
- culturable command area proposed to be irrigated in a season
- gross command area occupied by canals and roads
Show answer & solution
Answer: (C) culturable command area proposed to be irrigated in a season
Irrigation intensity = area planned to be irrigated / CCA, expressed as a percentage.
Question 7
The culturable command area (CCA) is the
- part of the gross command area that is fit for cultivation
- area irrigated by tube wells within the command
- area actually sown to crops in a given season
- entire area within the command boundary including villages and roads
Show answer & solution
Answer: (A) part of the gross command area that is fit for cultivation
CCA excludes land unfit for cultivation such as ponds, roads and barren land.
Question 8
Compared with the CCA, the gross command area (GCA) is
- unrelated, since the GCA is measured along the canal alone
- equal to the CCA less the area under the water channels and bunds
- larger or equal, since it includes the unculturable land in the command
- smaller, since it excludes the area occupied by villages, roads and ponds
Show answer & solution
Answer: (C) larger or equal, since it includes the unculturable land in the command
GCA covers the whole command boundary, so it is at least as large as the CCA.
Question 9
Crop rotation, such as a kharif crop followed by a rabi crop, means
- growing different crops in planned succession on the same field
- leaving the field fallow for a full year after each crop
- growing two crops together in alternate rows of a field
- growing one crop in the same field every season with extra fertiliser
Show answer & solution
Answer: (A) growing different crops in planned succession on the same field
Rotation varies the crops over seasons to maintain soil fertility and limit pests and diseases.
Question 10
The overall efficiency of an irrigation system is obtained as the
- arithmetic mean of the storage, conveyance and application efficiencies
- product of the storage, conveyance and field application efficiencies
- ratio of the discharge at the canal head to that at the tail
- ratio of the duty to the delta measured at the outlet
Show answer & solution
Answer: (B) product of the storage, conveyance and field application efficiencies
Efficiencies of successive stages multiply, so overall efficiency is lower than any single stage.
Question 11
Irrigation scheduling decides when and how much to irrigate, and is based mainly on
- the farmer's convenience and the availability of labour in the village
- a fixed calendar interval used for every crop and every soil type
- the design discharge of the canal and its full supply depth
- the crop's stage-wise water need, soil moisture and weather
Show answer & solution
Answer: (D) the crop's stage-wise water need, soil moisture and weather
Scheduling matches water applications to crop need, soil water storage and climate.
Question 12
Participatory irrigation management (PIM) involves
- sharing of operation and maintenance between the irrigation agency and user groups
- withdrawing the irrigation agency from the system and abolishing all water charges
- handing the design and construction of headworks to individual farmers
- fixing water allocations at a central office without any farmer input
Show answer & solution
Answer: (A) sharing of operation and maintenance between the irrigation agency and user groups
In PIM, farmer organisations take over part of the management alongside the irrigation agency.
Question 13
- area irrigated per unit discharge over the base period of the crop
- discharge needed to irrigate a unit area of land for one day
- volume of water needed per unit area over the base period of the crop
- depth of water applied to the field in a single irrigation
Show answer & solution
Answer: (A) area irrigated per unit discharge over the base period of the crop
Duty relates continuous discharge to the area it can irrigate over the base period (e.g. hectares per cumec).
Question 14
The delta of a crop is the
- total depth of water a crop requires during its base period
- depth of water in the canal at its full supply level
- area irrigated per cumec of discharge during the base period of the crop
- depth of water standing in the field after a single watering
Show answer & solution
Answer: (A) total depth of water a crop requires during its base period
Delta is the cumulative water depth needed over the whole base period.
Question 15
A crop has a duty of 864 ha per cumec on its field and a base period of 100 days. Its delta is
- 0.5 m
- 0.8 m
- 1.0 m
- 1.2 m
Show answer & solution
Answer: (C) 1.0 m
Delta = 8.64 B / D = 8.64 x 100 / 864 = 1.0 m.
Question 16
The base period of a crop is the time between its
- first watering and its last watering before harvest
- land preparation and harvest, including any fallow period
- two successive waterings
- sowing and germination
Show answer & solution
Answer: (A) first watering and its last watering before harvest
Base period is measured from the first to the last watering.
Question 17
For a given canal discharge, a larger duty means that
- the crop requires a longer base period
- more water is delivered per hectare to the crop
- less land can be irrigated with that discharge
- more land can be irrigated with that discharge
Show answer & solution
Answer: (D) more land can be irrigated with that discharge
Duty is area per unit discharge, so higher duty serves a larger area.
Question 18
Other factors being equal, the duty of water is higher for
- a canal in sandy soil, because the soil stores more of the water
- a canal in heavy clay, because seepage losses are smaller
- a field flooded deeply, because more of the water reaches the roots
- an unlined canal, because the lining adds to the water demand
Show answer & solution
Answer: (B) a canal in heavy clay, because seepage losses are smaller
Lower conveyance losses mean less discharge is needed for the same irrigated area.
Question 19
For the same irrigated area, the duty measured at the field is, compared with that at the canal head,
- the same, since duty depends on the crop and not on the location
- lower, since the discharge increases from the head towards the field
- higher, since conveyance losses reduce the discharge reaching the field
- lower, since extra evaporation at the field adds to the discharge needed
Show answer & solution
Answer: (C) higher, since conveyance losses reduce the discharge reaching the field
Less discharge reaches the field for the same area, so the field duty is greater.
Question 20
Kor watering, the first watering given to the young crop, is characterised by
- the same depth as every later watering of that crop in the season
- a greater depth than later waterings, to help establish the young crop
- a smaller depth than later waterings, to avoid disturbing the seedlings
- application only just before harvest to ease the cutting of the crop
Show answer & solution
Answer: (B) a greater depth than later waterings, to help establish the young crop
Kor depth is larger than the depth of subsequent waterings.
Question 21
Per unit area, the water requirement of rice, a kharif crop, compared with wheat, a rabi crop, is generally
- about equal, since delta depends only on the climate
- lower, since rice roots go deeper than wheat roots
- much higher, since rice is grown under ponded water
- lower, since rice transpires less than wheat
Show answer & solution
Answer: (C) much higher, since rice is grown under ponded water
Ponding and puddling make the delta of rice far larger than that of wheat.
Question 22
The cropping pattern of a command is an important input for
- fixing the crest level of the diversion weir at the headworks
- estimating peak water demand and the canal capacity
- choosing the lining material for the watercourses of the command
- deciding the alignment of the main canal along the ridge of the area
Show answer & solution
Answer: (B) estimating peak water demand and the canal capacity
Each crop has its own duty, delta and season, so the pattern fixes the total demand.
Question 23
The design discharge of a canal is generally fixed on the basis of the
- peak water demand of the command, with canal losses
- average demand over the whole crop year of the command area
- minimum demand in the rabi season of the command area
- annual runoff of the river available at the headworks site
Show answer & solution
Answer: (A) peak water demand of the command, with canal losses
A canal must carry the peak demand, estimated from the cropping pattern, duty and losses.
Question 24
Basin irrigation is a surface method in which
- the field is divided into level bunded basins flooded to the required depth
- a sheet of water flows down long sloping strips separated by low ridges
- water runs in narrow channels between the rows of the crop, on ridges
- water is sprayed through nozzles mounted on risers above the crop canopy
Show answer & solution
Answer: (A) the field is divided into level bunded basins flooded to the required depth
Basins are level, diked compartments filled to the desired depth, as commonly used for rice.
Question 25
Land levelling before surface irrigation is done mainly to
- create small depressions so that water ponds in every part of the field
- break up a hard pan so that percolation below the field increases
- lower the water table beneath the field before sowing the crop
- obtain a uniform surface slope so water spreads and infiltrates evenly
Show answer & solution
Answer: (D) obtain a uniform surface slope so water spreads and infiltrates evenly
A well-graded surface gives uniform water distribution and better efficiency.
Question 26
Which group consists of surface (gravity) irrigation methods?
- basin, border and furrow
- drip, bubbler and subsurface drip
- sprinkler, rain-gun and centre-pivot
- micro-sprayer, drip and sprinkler
Show answer & solution
Answer: (A) basin, border and furrow
Basin, border and furrow methods apply water by gravity flow over the field surface.
Question 27
In border irrigation, the field is divided into
- furrows between the crop rows with lateral wetting of the ridges
- plots in which water is applied drop by drop at each plant of the crop
- small level compartments that are flooded to a uniform depth and then drained
- long narrow strips separated by low ridges, down which a sheet of water flows
Show answer & solution
Answer: (D) long narrow strips separated by low ridges, down which a sheet of water flows
Border strips carry a flowing sheet of water that infiltrates as it advances.
Question 28
In furrow irrigation, water is
- sprayed into the air from rotating nozzles over the whole crop canopy
- run in small channels between rows, wetting the ridges by lateral seepage
- released drop by drop at the base of each plant through small emitters
- spread as a sheet over the entire field surface at once from a channel
Show answer & solution
Answer: (B) run in small channels between rows, wetting the ridges by lateral seepage
Furrows keep the foliage dry and suit row crops.
Question 29
The choice among basin, border and furrow methods depends on the
- crop, field slope, soil infiltration rate and stream size available
- canal rank and the length of the watercourse serving the field
- cost of land and the distance of the field from the market town
- wind speed and air temperature prevailing at the time of irrigation
Show answer & solution
Answer: (A) crop, field slope, soil infiltration rate and stream size available
These agronomic and hydraulic factors determine which method gives good uniformity and efficiency.
Question 30
Sprinkler irrigation applies water by
- releasing it drop by drop into the root zone of each individual plant through tubes
- flooding bunded basins from open channels laid along the sides of the field
- running it through furrows between the crop rows by gravity flow of water
- spraying it through pipes and nozzles under pressure, so it falls like rain
Show answer & solution
Answer: (D) spraying it through pipes and nozzles under pressure, so it falls like rain
Sprinklers use a pressurised pipe network and nozzles to imitate rainfall.
Question 31
Drip irrigation applies water by
- raising the water table so that the roots draw it up by capillarity from below
- spraying it into the air through high-pressure nozzles over the whole crop
- delivering it slowly, drop by drop, to the root zone through emitters
- flooding the field uniformly from an open channel by gravity flow of water
Show answer & solution
Answer: (C) delivering it slowly, drop by drop, to the root zone through emitters
Emitters place small volumes right at each plant.
Question 32
Compared with surface irrigation, sprinkler and drip systems generally offer
- lower capital cost and better suitability for flooded rice cultivation
- no need for any pressure source on level land having a high water table
- higher application efficiency, suitability for rolling land and fertigation
- lower pumping cost and no need for filtration of the irrigation water
Show answer & solution
Answer: (C) higher application efficiency, suitability for rolling land and fertigation
Pressurised systems cut percolation and runoff losses and allow fertiliser to be applied with the water.
Question 33
Compared with sprinklers, drip irrigation specifically offers
- higher operating pressure and wetting of the whole canopy
- lower filtration needs, since water passes through wide orifices
- lower evaporation losses and less wetting of the plant foliage
- better suitability for dense field crops such as wheat
Show answer & solution
Answer: (C) lower evaporation losses and less wetting of the plant foliage
Applying water near the root zone reduces evaporation and foliar disease risk.
Question 34
A characteristic maintenance problem of drip irrigation is
- large evaporation losses from the droplets sprayed into the air
- very high operating pressure at every emitter, higher than for sprinklers
- clogging of emitters by sediment, salts or algae, calling for filtration
- inability to apply fertiliser through the irrigation system
Show answer & solution
Answer: (C) clogging of emitters by sediment, salts or algae, calling for filtration
Small emitter orifices block easily unless the water is properly filtered.
Question 35
Sprinkler systems are available in configurations such as
- portable, solid-set and centre-pivot systems
- basin, border and furrow systems laid out with bunds and ridges
- bubbler, trickle and wick systems fitted to individual plants
- gated pipe, siphon tube and surge flow systems for row crops
Show answer & solution
Answer: (A) portable, solid-set and centre-pivot systems
Sprinkler layouts range from portable lines to permanent solid-set and large mechanised systems.
Question 36
Micro-sprinklers are used particularly for
- orchards and widely spaced crops, wetting more area than a drip emitter
- paddy fields that need standing water through the whole crop season
- large fields needing high-pressure rain guns to cover long distances
- closely sown wheat requiring uniform sheet coverage of the whole field
Show answer & solution
Answer: (A) orchards and widely spaced crops, wetting more area than a drip emitter
They fall between drip and sprinkler, giving a larger wetted zone per tree.
Question 37
The higher capital cost of drip and sprinkler systems is weighed against
- freedom from any need for filtration and maintenance of the system
- higher losses by deep percolation below the root zone of the crop grown
- lower energy bills than gravity canal irrigation would normally involve
- water and labour savings and yield gains, notably where water is scarce
Show answer & solution
Answer: (D) water and labour savings and yield gains, notably where water is scarce
Savings in water and labour and better yields can justify the higher investment.
Question 38
Subsidies for drip and sprinkler systems are mainly intended to
- increase the quantity of water applied per hectare of the crop
- replace the farmers' holdings with large state-run farms
- reduce the area of land lying under canal command in the province
- promote efficient use of scarce irrigation water
Show answer & solution
Answer: (D) promote efficient use of scarce irrigation water
Such support aims at water saving as scarcity and competition for water grow.