Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Irrigation: Canal Design, Regulation, Outlets & Falls

Civil Engineering · Irrigation

47 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

A watershed (ridge) canal is advantageous mainly because it

  1. follows a contour and so crosses many natural drainages on its way
  2. commands land on one side only, but needs very few falls along its length
  3. can be built only in flat areas where there is no natural ground slope
  4. commands land on either side and needs no cross-drainage works
Show answer & solution

Answer: (D) commands land on either side and needs no cross-drainage works

Following the ridge line lets gravity flow reach either side without crossing drainage lines.

Question 2

A contour canal, aligned along a ground contour, generally

  1. runs along the ridge of the area so it never meets a stream
  2. irrigates land on either side and avoids all drainage crossings en route
  3. is built only in flat deltaic plains where the ground slope is nil
  4. irrigates the downhill side only and must cross drainage lines
Show answer & solution

Answer: (D) irrigates the downhill side only and must cross drainage lines

A contour canal commands one side and meets the drainage that runs down the slope.

Question 3

A canal escape is provided mainly to

  1. dispose of surplus water from the canal into a natural drain
  2. measure the discharge entering a distributary from the parent canal
  3. supply water to the outlets at the tail of a distributary in lean periods
  4. raise the canal water level so that higher fields can be commanded
Show answer & solution

Answer: (A) dispose of surplus water from the canal into a natural drain

Escapes release excess water that arrives from over-supply or sudden reduction in demand.

Question 4

On the basis of the source of supply, canals are classified as

  1. contour canals and ridge canals, depending on the alignment
  2. perennial canals and inundation canals
  3. main canals and branch canals, with distributaries below them
  4. lined canals and unlined canals, depending on the bed treatment
Show answer & solution

Answer: (B) perennial canals and inundation canals

Perennial canals have a continuous supply, while inundation canals draw water only during high river stages.

Question 5

In descending order of size, the usual canal hierarchy is

  1. main canal, distributary, branch canal and watercourse
  2. watercourse, distributary, branch canal and main canal
  3. branch canal, main canal, watercourse and distributary
  4. main canal, branch canal, distributary and watercourse
Show answer & solution

Answer: (D) main canal, branch canal, distributary and watercourse

Capacity decreases step by step from the main canal down to the watercourse.

Question 6

A watercourse in the canal hierarchy is used to

  1. take surplus water from the tail of a canal to a natural drain or river
  2. link two branch canals near their tail ends during lean periods of supply
  3. carry water from the outlet on a distributary to the fields
  4. carry water from the river to the head of the main canal
Show answer & solution

Answer: (C) carry water from the outlet on a distributary to the fields

Watercourses are the last link between the outlet and the fields.

Question 7

Silting of a canal bed occurs mainly when the flow velocity is

  1. constant over the whole length of the canal from head to tail
  2. exactly equal to the critical velocity of the channel at the design depth
  3. higher than the maximum non-eroding velocity of the boundary material
  4. lower than needed to keep the sediment in suspension
Show answer & solution

Answer: (D) lower than needed to keep the sediment in suspension

Too low a velocity cannot carry the sediment, which then deposits on the bed and cuts capacity.

Question 8

Scouring of a canal bed and banks occurs mainly when the flow velocity is

  1. exactly equal to the critical velocity of the channel at the design depth
  2. higher than the maximum non-eroding velocity of the boundary
  3. lower than the velocity needed to carry the silt load of the canal
  4. below the critical velocity while the depth exceeds the design depth
Show answer & solution

Answer: (B) higher than the maximum non-eroding velocity of the boundary

Velocities above the permissible limit erode the bed and banks.

Question 9

The freeboard of a canal is the vertical distance between the

  1. bed level and the top of the bank
  2. bed level and the full supply level
  3. full supply level and the top of the bank
  4. top of the bank and the natural ground level
Show answer & solution

Answer: (C) full supply level and the top of the bank

Freeboard is the safety margin above the full supply level that guards against overtopping.

Question 10

Periodic desilting of canals is carried out mainly to

  1. increase seepage so that the groundwater in the area is recharged
  2. reduce the velocity below the critical limit of the channel
  3. raise the bed level so that the outlets receive more working head
  4. restore the cross-section and capacity reduced by deposited silt
Show answer & solution

Answer: (D) restore the cross-section and capacity reduced by deposited silt

Deposited silt reduces the area and capacity of the channel, so it must be removed.

Question 11

The longitudinal bed slope of a canal is generally chosen to

  1. be as steep as the ground permits, since higher velocity is always better
  2. carry the design discharge at a non-silting, non-scouring velocity
  3. be nearly flat to maximise the stored depth in the canal
  4. be fixed at 1 in 1000 for every canal, whatever the discharge
Show answer & solution

Answer: (B) carry the design discharge at a non-silting, non-scouring velocity

Slope follows from the design discharge and the permissible velocity for the soil.

Question 12

A cross-regulator on a main canal, just downstream of an off-take, is provided to

  1. dispose of surplus water into a natural drain situated near the canal
  2. measure the supply entering each of the watercourses
  3. drop the canal level safely where the natural ground slope is steep
  4. hold up the water level so the off-take can draw its share
Show answer & solution

Answer: (D) hold up the water level so the off-take can draw its share

It maintains the required upstream level at the off-take of a branch or distributary.

Question 13

A head regulator at the take-off of a branch canal or distributary serves to

  1. raise the river level at a diversion headwork for the canal
  2. pass surplus water to a drain at the tail of the canal system
  3. reduce the energy of the water as it drops at a fall
  4. control the discharge admitted into the off-taking channel
Show answer & solution

Answer: (D) control the discharge admitted into the off-taking channel

The head regulator admits and regulates the supply into the offtaking channel.

Question 14

A canal outlet is the structure that

  1. carries the canal across a natural stream at a lower level
  2. removes surplus water from the distributary at its tail end
  3. delivers a regulated discharge from a distributary to a watercourse
  4. holds up the level in a distributary for the next downstream off-take
Show answer & solution

Answer: (C) delivers a regulated discharge from a distributary to a watercourse

The outlet is the link between the distributary and the farmers' watercourse.

Question 15

The discharge of a non-modular outlet

  1. depends on the water levels in the distributary and the watercourse
  2. depends on the distributary level but not on the watercourse level
  3. stays constant despite changes in the two water levels
  4. depends only on the opening that was set at the time of construction
Show answer & solution

Answer: (A) depends on the water levels in the distributary and the watercourse

A non-modular outlet works under a head difference that varies with the two levels.

Question 16

The discharge of a semi-module outlet

  1. depends on the distributary level but not on the watercourse level, in working range
  2. varies directly with the difference of the two levels, like a plain open orifice
  3. is independent of the levels in the distributary and watercourse within working limits
  4. is independent of the distributary level and depends only on the watercourse level
Show answer & solution

Answer: (A) depends on the distributary level but not on the watercourse level, in working range

A semi-module is insulated from watercourse level changes but still responds to the distributary level.

Question 17

A rigid module is an outlet whose discharge

  1. rises linearly with the supply carried by the distributary
  2. varies with the distributary level but not with the watercourse level, within limits
  3. stays nearly constant within working limits whatever the two water levels
  4. varies in proportion to the difference between the two water levels in the channels
Show answer & solution

Answer: (C) stays nearly constant within working limits whatever the two water levels

A rigid module gives an almost fixed discharge, independent of the two water levels.

Question 18

The flexibility of an outlet is the ratio of the

  1. fractional change in outlet discharge to that in distributary discharge
  2. outlet discharge to the design discharge of the watercourse that it serves
  3. watercourse discharge to the gross command area of the outlet
  4. fractional change in watercourse level to that in distributary level
Show answer & solution

Answer: (A) fractional change in outlet discharge to that in distributary discharge

Flexibility F = (dq/q) / (dQ/Q) measures how an outlet responds to changes in the parent channel.

Question 19

Water is shared equitably among outlets on a distributary when the outlets

  1. have a high flexibility above two and are placed only in the head reaches
  2. are rigid modules set to give extra discharge to the head-end farmers
  3. are proportional, with flexibility near one, so each shares any change
  4. are sized equally irrespective of the area they command
Show answer & solution

Answer: (C) are proportional, with flexibility near one, so each shares any change

With flexibility near unity every outlet gains or loses in proportion to the supply.

Question 20

Tail-end areas of a canal system are of concern because they

  1. are served first, since water is supplied from the tail in rotation in lean periods
  2. receive surplus water because the canal bed is lower near the tail
  3. share in every cut in supply equally with the head reaches
  4. are most vulnerable to shortage in scarcity or with poor outlet design
Show answer & solution

Answer: (D) are most vulnerable to shortage in scarcity or with poor outlet design

Tail-end farmers are typically the first to suffer when supplies fall short.

Question 21

A simple vertical-drop fall consists of

  1. an abrupt drop in the bed, the water falling on a cistern that dissipates its energy
  2. a long gently sloping glacis joining the upstream and downstream bed levels of the canal
  3. baffle blocks on a raised crest with no drop in the canal bed
  4. a pipe that takes the canal beneath a road without any loss of energy at all
Show answer & solution

Answer: (A) an abrupt drop in the bed, the water falling on a cistern that dissipates its energy

The falling water loses energy in the cistern below the drop.

Question 22

A glacis-type fall differs from a vertical drop in having

  1. a raised crest that increases the upstream bed level of the canal at the fall
  2. a vertical wall over which the water falls into a deep pool
  3. a sloping surface that guides the flow down and dissipates energy by a jump
  4. a siphon barrel placed beneath the downstream bed of the canal at the fall
Show answer & solution

Answer: (C) a sloping surface that guides the flow down and dissipates energy by a jump

The glacis allows smoother and more efficient energy dissipation.

Question 23

Cross-regulators and head regulators are classed as

  1. regulating structures that control level or discharge at a junction, unlike falls
  2. canal outlets that deliver water to the watercourses of the farmers' fields
  3. cross-drainage works that carry the canal across natural streams and nullahs
  4. canal falls that dissipate energy where the ground slopes steeply
Show answer & solution

Answer: (A) regulating structures that control level or discharge at a junction, unlike falls

Regulators deal with level and discharge control, while falls deal with change in bed level.

Question 24

On the basis of operation, canal escapes are of types such as

  1. surplus escapes acting automatically above a set level, and gated sluice escapes
  2. main escapes and branch escapes, according to the rank of the canal concerned
  3. inlet escapes and outlet escapes, according to the water level of the canal
  4. lined escapes and unlined escapes, according to the bed material
Show answer & solution

Answer: (A) surplus escapes acting automatically above a set level, and gated sluice escapes

Escapes are either automatic (weir type) or gate-operated.

Question 25

Stone or concrete pitching of canal bed and banks at bends and below structures is provided to

  1. increase the flow velocity at bends so that the canal remains self-cleaning
  2. raise the canal bed to improve the command of the outlets downstream
  3. protect them from erosion caused by locally high velocity and turbulence
  4. store extra water in the canal for the dry-season supply
Show answer & solution

Answer: (C) protect them from erosion caused by locally high velocity and turbulence

Pitching armours vulnerable parts of the channel against scour.

Question 26

Bridges are provided at planned spacing along a canal to

  1. carry road and rail traffic over the canal without obstructing its flow
  2. measure the canal discharge by means of the bridge opening
  3. carry the drainage of a natural stream across the canal at a lower level
  4. regulate the water level of the canal for the off-takes downstream
Show answer & solution

Answer: (A) carry road and rail traffic over the canal without obstructing its flow

A canal is a linear barrier, so crossings are planned to maintain connectivity.

Question 27

Roads along the top of canal banks are provided mainly for

  1. lining the canal bed with compacted material
  2. raising the full supply level of the canal
  3. inspection and maintenance access along the canal
  4. supplying irrigation water to adjoining fields directly
Show answer & solution

Answer: (C) inspection and maintenance access along the canal

Bank roads give officials access for inspection, patrolling and maintenance.

Question 28

Uncontrolled weed growth in a canal results in

  1. lower water levels at the off-takes on the canal
  2. faster flow and a greater risk of scour in the reach
  3. reduced roughness and increased capacity of the channel
  4. greater roughness and reduced discharge capacity
Show answer & solution

Answer: (D) greater roughness and reduced discharge capacity

Weeds slow the flow and raise water levels for a given discharge, so they must be cleared.

Question 29

The basic canal alignment patterns are

  1. river-bank, road-side and boundary alignments
  2. watershed (ridge), contour and side-slope alignments
  3. valley, trough and delta alignments
  4. straight, curved and spiral alignments chosen by survey cost
Show answer & solution

Answer: (B) watershed (ridge), contour and side-slope alignments

Alignment type is chosen according to topography.

Question 30

Canal lining is provided mainly to

  1. increase seepage so as to feed the wells of the adjoining fields and recharge them
  2. remove the need for any bed slope in the canal, which can then be horizontal
  3. reduce seepage, raise velocity and capacity, and help control waterlogging
  4. increase roughness so as to slow the flow and recharge the groundwater
Show answer & solution

Answer: (C) reduce seepage, raise velocity and capacity, and help control waterlogging

Lining cuts seepage losses, improves hydraulic efficiency and prevents seepage-induced rise of the water table.

Question 31

The most efficient hydraulic section of a canal for a given area has the

  1. maximum wetted perimeter
  2. minimum wetted perimeter
  3. minimum hydraulic mean depth
  4. maximum freeboard
Show answer & solution

Answer: (B) minimum wetted perimeter

Least wetted perimeter gives the greatest discharge for the area and least friction and excavation or lining.

Question 32

Commonly used canal lining materials are

  1. timber planks, bamboo mats and straw laid along the bed and banks
  2. cement concrete, brick or tile, and geomembrane or compacted clay
  3. peat, loose topsoil and organic silt laid along the bed and banks
  4. dry sand, gravel and loose boulders laid in layers over the bed
Show answer & solution

Answer: (B) cement concrete, brick or tile, and geomembrane or compacted clay

Concrete, brick or tile and membrane or clay linings are the practical choices.

Question 33

A canal fall is provided to

  1. measure the discharge of the canal by means of the drop in its bed level
  2. divert surplus water from the canal to a nearby natural drain at the fall
  3. lower the canal bed where the ground slope exceeds the design bed slope
  4. raise the water level so that high ground can be commanded
Show answer & solution

Answer: (C) lower the canal bed where the ground slope exceeds the design bed slope

Falls step down the canal and dissipate the surplus energy.

Question 34

The cistern of a canal fall is the

  1. weir crest that raises the water level upstream of the fall structure
  2. chamber that accelerates the flow before it enters the downstream canal
  3. floor below the downstream bed where the falling water loses its energy
  4. storage basin that supplies the watercourses during canal closure
Show answer & solution

Answer: (C) floor below the downstream bed where the falling water loses its energy

The cistern holds the water cushion and hydraulic jump that protects the downstream bed.

Question 35

A hydraulic jump below a fall is useful because it

  1. changes subcritical flow into supercritical flow to increase the velocity
  2. converts the potential energy of the water into scour downstream
  3. increases the specific energy of the flow below the fall
  4. dissipates energy by changing the flow from supercritical to subcritical
Show answer & solution

Answer: (D) dissipates energy by changing the flow from supercritical to subcritical

The jump destroys excess kinetic energy and protects the channel from erosion.

Question 36

Modernisation of an existing irrigation system typically includes

  1. replacing all outlets by larger orifices to increase the supply to the fields
  2. lining, better regulation and measurement structures, and flexible delivery
  3. raising water charges while leaving the structures of the system unchanged
  4. abandoning the distributaries and relying wholly on rainfall
Show answer & solution

Answer: (B) lining, better regulation and measurement structures, and flexible delivery

Modernisation improves efficiency and reliability of delivery.

Question 37

Kennedy's theory of canal design in alluvial soil is based on the

  1. critical velocity, depending on depth, that neither silts nor scours
  2. tractive force acting on the bed of the channel per unit area of the bed
  3. permissible velocity for the boundary material in rigid channels with lining
  4. regime width, which depends on the silt factor and the discharge
Show answer & solution

Answer: (A) critical velocity, depending on depth, that neither silts nor scours

Kennedy related the non-silting, non-scouring velocity to the depth of flow, using the critical velocity ratio m.

Question 38

A channel is in regime, as per Lacey, when

  1. its bed slope is fixed while the velocity adjusts to the discharge in the channel
  2. silting and scouring balance, with slope, width and depth in equilibrium
  3. it carries no silt at all and has rigid banks
  4. its velocity equals Kennedy's critical velocity at every depth of flow
Show answer & solution

Answer: (B) silting and scouring balance, with slope, width and depth in equilibrium

A regime channel neither silts nor scours over time for the given discharge and silt factor.

Question 39

The silt factor f in Lacey's theory depends on the

  1. total silt load carried per cumec of the flow in the canal
  2. mean size of the silt particles in the bed material
  3. chemical composition of the silt carried by the canal
  4. depth of the silt layer lying on the canal bed
Show answer & solution

Answer: (B) mean size of the silt particles in the bed material

Lacey's silt factor is f = 1.76 times the square root of the mean particle size d in mm.

Question 40

Berms on the sides of an unlined canal serve to

  1. improve the hydraulic efficiency of the section by raising the wetted perimeter
  2. strengthen the banks and leave room for silt and future desilting
  3. act as the main lining of the channel at the bed level
  4. increase the flow area of the canal and so increase its discharge capacity
Show answer & solution

Answer: (B) strengthen the banks and leave room for silt and future desilting

Berms strengthen banks and give space for maintenance.

Question 41

In Kennedy's theory the critical velocity ratio m is introduced to

  1. account for the seasonal variation of the canal discharge
  2. adjust the formula for different side slopes of the canal banks
  3. allow for the curvature of the canal alignment at bends
  4. adjust the critical velocity formula to different silt grades
Show answer & solution

Answer: (D) adjust the critical velocity formula to different silt grades

m is a soil-dependent multiplier applied to the critical velocity.

Question 42

Unlike Kennedy's theory, Lacey's regime theory also gives

  1. a direct expression for the regime bed slope
  2. the critical velocity ratio for each type of soil
  3. the permissible velocity of rigid canal linings
  4. the seepage loss per unit wetted area of the canal
Show answer & solution

Answer: (A) a direct expression for the regime bed slope

Kennedy's equations do not fix the slope directly, whereas Lacey's give width, depth and slope.

Question 43

Kennedy's and Lacey's theories are empirical, being based on

  1. design curves developed for rocky mountain channels of steep slope and high velocity
  2. observations of working canals in the alluvial plains of the Indus and neighbouring river basins
  3. first-principles derivation from the equations of fluid motion
  4. laboratory flume studies on small rigid concrete channels with fixed boundaries
Show answer & solution

Answer: (B) observations of working canals in the alluvial plains of the Indus and neighbouring river basins

These theories were derived from field data of stable working canals.

Question 44

A canal in non-alluvial (rocky or firm) soil is usually designed with

  1. Lacey's regime equations with the silt factor assumed for rock boundaries
  2. Kennedy's equations with a critical velocity ratio of 1.0 assumed for rock
  3. a permissible-velocity approach, as regime theories suit alluvial channels
  4. Khosla's exit gradient criterion applied to the canal bed
Show answer & solution

Answer: (C) a permissible-velocity approach, as regime theories suit alluvial channels

Regime theories were developed for alluvial channels only.

Question 45

Side slopes of an earthen canal are fixed mainly to

  1. keep the banks stable, according to the angle of repose of the soil
  2. provide a path along the banks for silt to deposit
  3. raise the canal discharge by adding more wetted area to the section
  4. reduce seepage by lowering the depth of water in the canal
Show answer & solution

Answer: (A) keep the banks stable, according to the angle of repose of the soil

Slopes flatter than the soil's angle of repose prevent slips.

Question 46

For the same discharge, a lined canal compared with an unlined one generally needs

  1. a larger section, because the lining adds thickness to the channel
  2. a smaller section, since lower roughness permits a higher velocity
  3. a wider section, to keep the velocity below the regime value
  4. the same section, since roughness affects only the seepage losses
Show answer & solution

Answer: (B) a smaller section, since lower roughness permits a higher velocity

Smooth lining raises velocity and reduces the required area.

Question 47

If no fall is provided where the ground slope is much steeper than the canal slope, the canal will

  1. silt, because the velocity drops below the limit for the soil
  2. become waterlogged, because the bed level of the canal rises
  3. lose less water, because the gradient of the canal is steeper
  4. scour, because the velocity exceeds the non-eroding limit
Show answer & solution

Answer: (D) scour, because the velocity exceeds the non-eroding limit

Following the steep ground would raise the velocity beyond the safe non-scouring limit.

Practice these 47 questions interactively →