What is hydrotreating?
Show answer & solution
Answer: (B) Catalytic treatment with hydrogen to remove sulphur, nitrogen, oxygen and metals and saturate olefins
Co-Mo and Ni-Mo catalysts are used.
Chemical Engineering · Petroleum Refining & Natural Gas
36 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is hydrotreating?
Answer: (B) Catalytic treatment with hydrogen to remove sulphur, nitrogen, oxygen and metals and saturate olefins
Co-Mo and Ni-Mo catalysts are used.
What is the hydrodesulphurisation reaction product of sulphur compounds?
Answer: (D) Hydrogen sulphide
H₂S is removed by amine and converted to sulphur in a Claus unit.
What is the Euro 5 limit on sulphur in diesel?
Answer: (B) 10 ppm
Pakistan moved toward Euro 5 fuels for road transport.
What is the Merox process?
Answer: (C) Catalytic oxidation of mercaptans in LPG, gasoline or kerosene to disulphides or their extraction with caustic
Merox stands for mercaptan oxidation.
What is sweetening of products?
Answer: (A) Removing or converting mercaptans and H₂S that cause odour and corrosion
The doctor test detects mercaptans.
What does octane number of gasoline measure?
Answer: (C) Its resistance to knocking in spark-ignition engines
Isooctane is 100 and n-heptane 0.
What is the difference between RON and MON?
Answer: (D) RON is measured under milder conditions and is usually higher than MON
Anti-knock index = (RON + MON)/2.
What was the purpose of adding tetraethyl lead to gasoline?
Answer: (A) Raising octane number
It was phased out because of lead toxicity; Pakistan banned leaded petrol around 2001.
Which compounds are used today to raise gasoline octane?
Answer: (A) Reformate, alkylate, isomerate and oxygenates such as MTBE or ethanol
Aromatics are limited by fuel specifications.
What does cetane number of diesel indicate?
Answer: (B) Its ignition quality; higher means shorter ignition delay
n-Hexadecane (cetane) is 100.
Which hydrocarbon type has the best cetane number?
Answer: (D) Straight-chain paraffins
Aromatics give good octane but poor cetane.
What is the cetane index?
Answer: (C) An estimate of cetane number from density and distillation data
It is calculated by ASTM D4737.
What is jet fuel (Jet A-1) mainly made from?
Answer: (D) The kerosene fraction, treated to meet strict freezing point, smoke point and stability limits
Its freezing point must be below −47 °C.
What are lubricating oil base stocks made from?
Answer: (A) Vacuum distillates and deasphalted oil refined by solvent extraction, dewaxing and finishing
National Refinery in Karachi produces lube base oils.
What is the viscosity index of a lubricant?
Answer: (B) A measure of how little its viscosity changes with temperature
Paraffinic base oils have high VI.
What is solvent dewaxing of lube oils?
Answer: (C) Removing wax by dissolving oil in a solvent such as MEK–toluene, chilling and filtering out wax
It lowers the pour point.
What is furfural or NMP extraction used for in lube refining?
Answer: (C) Removing aromatics to improve viscosity index and oxidation stability
The raffinate is the base oil.
What is bitumen (asphalt)?
Answer: (A) The heavy residue of crude distillation used for roads and waterproofing
Penetration grade indicates hardness.
What does penetration grade 60/70 of bitumen indicate?
Answer: (D) The needle penetration in tenths of a millimetre at 25 °C
It is a common paving grade in Pakistan.
What is furnace oil (fuel oil)?
Answer: (B) A heavy residual fuel used in boilers, furnaces and power plants
High-sulphur furnace oil was widely used in Pakistani power plants.
What is product blending in a refinery?
Answer: (C) Mixing components to meet specifications at minimum cost
Linear programming optimises blends.
What are the main specifications of gasoline?
Answer: (B) Octane number, vapour pressure, distillation range, sulphur, benzene and aromatics content
Specifications ensure engine performance and emissions control.
What is the purpose of the sour water stripper in a refinery?
Answer: (D) Removing H₂S and ammonia from process water before reuse or treatment
Stripped gas goes to the sulphur recovery unit.
What is a sulphur recovery unit (SRU)?
Answer: (A) A Claus unit converting H₂S from amine regenerators to elemental sulphur
Tail gas treating raises recovery above 99%.
What is the purpose of amine treating in refineries?
Answer: (A) Removing H₂S and CO₂ from refinery fuel gas and LPG
MDEA and DEA are common.
What is the typical hydrotreating catalyst operating temperature?
Answer: (B) About 300–400 °C
Higher temperatures raise reaction rates but shorten catalyst life.
What is the doctor test?
Answer: (A) A qualitative test for mercaptans in fuels using sodium plumbite
A negative (sweet) result is required.
What does the copper strip corrosion test measure?
Answer: (D) The corrosiveness of fuels due to active sulphur compounds
A copper strip is immersed and its tarnish rated.
What is the purpose of antioxidant additives in gasoline?
Answer: (A) Preventing gum formation during storage
Gum deposits foul engines.
What is cold filter plugging point (CFPP) of diesel?
Answer: (D) The lowest temperature at which diesel passes through a standard filter in a given time
It indicates winter operability.
What is the typical freezing point specification for Jet A-1?
Answer: (C) Below −47 °C
Aircraft fly in very cold upper air.
What is high-speed diesel (HSD)?
Answer: (A) Diesel fuel for high-speed engines in vehicles and generators
It is the largest-selling fuel in Pakistan.
What is the purpose of hydrofinishing lube base oils?
Answer: (C) Improving colour and stability by mild hydrogenation
It replaces older clay treating.
What is a bitumen softening point?
Answer: (B) The temperature at which bitumen softens enough for a steel ball to sink through it in the ring-and-ball test
Higher softening point means harder bitumen.
What is polymer-modified bitumen?
Answer: (A) Bitumen blended with polymers such as SBS to improve elasticity and resistance to rutting
It is used on heavily trafficked roads in hot climates.
What is cutback bitumen?
Answer: (A) Bitumen diluted with a solvent such as kerosene to make it fluid at lower temperatures
The solvent evaporates after laying.