Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Petroleum Refining & Natural Gas: Primary Distillation

Chemical Engineering · Petroleum Refining & Natural Gas

34 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the first major processing step in a refinery?

  1. Desalting followed by atmospheric distillation
  2. Catalytic cracking
  3. Alkylation
  4. Blending
Show answer & solution

Answer: (A) Desalting followed by atmospheric distillation

Crude is heated and fractionated by boiling range.

Question 2

Why is crude oil desalted before distillation?

  1. To increase API gravity
  2. To remove sulphur
  3. To remove salts that cause corrosion, fouling and catalyst poisoning
  4. To add water
Show answer & solution

Answer: (C) To remove salts that cause corrosion, fouling and catalyst poisoning

Electrostatic desalters use wash water and an electric field.

Question 3

What corrosive acid forms in the crude unit overhead from salts in crude?

  1. Phosphoric acid
  2. Sulphuric acid
  3. Nitric acid
  4. Hydrochloric acid from hydrolysis of magnesium and calcium chlorides
Show answer & solution

Answer: (D) Hydrochloric acid from hydrolysis of magnesium and calcium chlorides

Neutralising amines and wash water control overhead corrosion.

Question 4

What is the typical temperature of crude leaving the fired heater to the atmospheric column?

  1. About 100 °C
  2. About 340–370 °C
  3. About 600 °C
  4. About 900 °C
Show answer & solution

Answer: (B) About 340–370 °C

Higher temperatures cause thermal cracking.

Question 5

In what order do products leave an atmospheric crude column from top to bottom?

  1. Residue, diesel, kerosene, naphtha
  2. Kerosene, naphtha, residue, diesel
  3. Gas and naphtha, kerosene, diesel (gas oil), and atmospheric residue
  4. Diesel, gas, residue, naphtha
Show answer & solution

Answer: (C) Gas and naphtha, kerosene, diesel (gas oil), and atmospheric residue

Lighter fractions rise higher in the column.

Question 6

What is the purpose of side strippers on a crude column?

  1. Removing light ends from side-draw products with steam to meet flash point
  2. Increasing product yield of gas
  3. Cooling the column
  4. Removing salts
Show answer & solution

Answer: (A) Removing light ends from side-draw products with steam to meet flash point

Stripping steam lowers partial pressure.

Question 7

Why is steam injected at the bottom of crude columns?

  1. To cool the residue
  2. To heat the crude
  3. To dissolve salts
  4. To lower hydrocarbon partial pressure and strip light components from the residue
Show answer & solution

Answer: (D) To lower hydrocarbon partial pressure and strip light components from the residue

It allows vaporisation without overheating.

Question 8

What is a pumparound in a crude column?

  1. A reflux drum
  2. A liquid drawn from the column, cooled and returned higher up to remove heat and improve vapour–liquid traffic
  3. A pump for feed only
  4. A product tank
Show answer & solution

Answer: (B) A liquid drawn from the column, cooled and returned higher up to remove heat and improve vapour–liquid traffic

Pumparounds recover heat to preheat crude.

Question 9

What is the crude preheat train?

  1. The desalter only
  2. The vacuum unit
  3. A network of exchangers heating crude with hot products and pumparounds before the furnace
  4. The tank farm
Show answer & solution

Answer: (C) A network of exchangers heating crude with hot products and pumparounds before the furnace

Good heat integration saves furnace fuel.

Question 10

Why is atmospheric residue distilled under vacuum?

  1. To separate heavy gas oils at lower temperatures without thermal cracking
  2. To remove gases
  3. To increase boiling points
  4. To add sulphur
Show answer & solution

Answer: (A) To separate heavy gas oils at lower temperatures without thermal cracking

Vacuum units operate at about 25–100 mm Hg absolute at the flash zone.

Question 11

What are the main products of the vacuum distillation unit?

  1. Kerosene and diesel
  2. Hydrogen and methane
  3. Naphtha and LPG
  4. Vacuum gas oils and vacuum residue
Show answer & solution

Answer: (D) Vacuum gas oils and vacuum residue

VGO feeds cracking units or lube plants.

Question 12

How is vacuum produced in a refinery vacuum column?

  1. By compressors pushing gas in
  2. By cooling the column
  3. By steam ejectors and condensers (or vacuum pumps)
  4. By removing crude
Show answer & solution

Answer: (C) By steam ejectors and condensers (or vacuum pumps)

Multistage ejectors are common.

Question 13

Which column internals are commonly used in vacuum columns to minimise pressure drop?

  1. Bubble cap trays
  2. Valve trays only
  3. Sieve trays with high weirs
  4. Structured or grid packing
Show answer & solution

Answer: (D) Structured or grid packing

Low pressure drop keeps flash zone vacuum deep.

Question 14

What is the overflash in a crude column?

  1. The extra vaporisation above product needs to provide wash liquid below the lowest side draw
  2. The flash point of products
  3. Excess steam
  4. The furnace outlet
Show answer & solution

Answer: (A) The extra vaporisation above product needs to provide wash liquid below the lowest side draw

It improves residue and gas oil separation.

Question 15

What is the end point of a fraction?

  1. The initial boiling point
  2. The maximum temperature reached in its distillation test
  3. The pour point
  4. The flash point
Show answer & solution

Answer: (B) The maximum temperature reached in its distillation test

It indicates the heaviest components present.

Question 16

What is the gap or overlap between two fractions?

  1. The furnace duty
  2. The difference between the 5% point of the heavier and 95% point of the lighter fraction
  3. The temperature of the flash zone
  4. The flow ratio
Show answer & solution

Answer: (B) The difference between the 5% point of the heavier and 95% point of the lighter fraction

A positive gap indicates good separation.

Question 17

What is the stabiliser column used for in a refinery?

  1. Removing LPG and light gases from naphtha
  2. Separating residue
  3. Cracking gas oil
  4. Removing water from crude
Show answer & solution

Answer: (A) Removing LPG and light gases from naphtha

The bottoms are stabilised naphtha.

Question 18

What is a naphtha splitter?

  1. A desalter
  2. A cracking unit
  3. A column separating naphtha into light naphtha and heavy naphtha
  4. A vacuum column
Show answer & solution

Answer: (C) A column separating naphtha into light naphtha and heavy naphtha

Heavy naphtha feeds the reformer.

Question 19

What is the typical cut range of kerosene?

  1. Below 0 °C
  2. About 400–550 °C
  3. About 30–80 °C
  4. About 150–250 °C
Show answer & solution

Answer: (D) About 150–250 °C

It is used as jet fuel and domestic fuel.

Question 20

What is the typical boiling range of diesel (gas oil)?

  1. About 500–600 °C
  2. About 250–360 °C
  3. Below 30 °C
  4. About 30–150 °C
Show answer & solution

Answer: (B) About 250–360 °C

Atmospheric gas oil is a major product.

Question 21

What is the effect of excessive furnace outlet temperature on crude distillation?

  1. Thermal cracking, coking of tubes and off-spec products
  2. No effect
  3. Higher yield of residue
  4. Lower yields of gas
Show answer & solution

Answer: (A) Thermal cracking, coking of tubes and off-spec products

Temperatures are limited to about 370 °C for atmospheric heaters.

Question 22

Which refinery in Pakistan is the oldest, established at Rawalpindi in 1922?

  1. Pak-Arab Refinery
  2. Pakistan Refinery Limited
  3. Attock Refinery Limited
  4. National Refinery
Show answer & solution

Answer: (C) Attock Refinery Limited

It processes local crudes from northern fields.

Question 23

What is the flash zone of a crude column?

  1. The top of the column
  2. The region where the partially vaporised feed enters and vapour separates from liquid
  3. The furnace
  4. The reflux drum
Show answer & solution

Answer: (B) The region where the partially vaporised feed enters and vapour separates from liquid

Its temperature and pressure determine overall vaporisation.

Question 24

What is the overhead product of an atmospheric crude column after condensation?

  1. Diesel
  2. Bitumen
  3. Unstabilised naphtha, gas and water
  4. Residue
Show answer & solution

Answer: (C) Unstabilised naphtha, gas and water

Water separates in the overhead drum boot.

Question 25

What is a topping plant?

  1. A simple refinery that only distils crude into straight-run products
  2. An LNG plant
  3. A petrochemical plant
  4. A conversion refinery
Show answer & solution

Answer: (A) A simple refinery that only distils crude into straight-run products

It produces a large share of fuel oil.

Question 26

Why are heater tubes in vacuum units larger in diameter at the outlet?

  1. To increase cracking
  2. To accommodate vapour expansion at low pressure and limit velocity and pressure drop
  3. To increase pressure
  4. To reduce cost only
Show answer & solution

Answer: (B) To accommodate vapour expansion at low pressure and limit velocity and pressure drop

Velocity steam also reduces coking.

Question 27

What is the purpose of wash oil in a vacuum column?

  1. Removing water
  2. Washing salts
  3. Cooling the column
  4. Washing entrained residue droplets from rising vapour to keep metals and carbon out of vacuum gas oil
Show answer & solution

Answer: (D) Washing entrained residue droplets from rising vapour to keep metals and carbon out of vacuum gas oil

The wash zone protects VGO quality.

Question 28

What is the typical vacuum residue use in a refinery without conversion units?

  1. Making LPG
  2. Making jet fuel
  3. Blending into fuel oil or making bitumen
  4. Making petrol
Show answer & solution

Answer: (C) Blending into fuel oil or making bitumen

Conversion units upgrade it to lighter products.

Question 29

What is the Pakistani refinery at Hub in Balochistan known as?

  1. PARCO
  2. Cnergyico (formerly Byco) refinery
  3. National Refinery
  4. Attock Refinery
Show answer & solution

Answer: (B) Cnergyico (formerly Byco) refinery

It has a single point mooring for crude import.

Question 30

What is the purpose of a crude unit overhead accumulator boot?

  1. Storing residue
  2. Measuring flow
  3. Collecting and removing water separated from condensed overhead hydrocarbons
  4. Heating crude
Show answer & solution

Answer: (C) Collecting and removing water separated from condensed overhead hydrocarbons

Water pH is monitored to control corrosion.

Question 31

Why is the atmospheric column pressure kept slightly above atmospheric?

  1. To create vacuum
  2. To allow overhead condensation with cooling water or air and flow to downstream units
  3. To increase boiling points greatly
  4. To cause cracking
Show answer & solution

Answer: (B) To allow overhead condensation with cooling water or air and flow to downstream units

Typical top pressure is about 1–2 bar gauge.

Question 32

What is the purpose of a pre-flash drum or column ahead of the crude heater?

  1. Removing light ends early to reduce furnace and column loads
  2. Desalting crude
  3. Adding water
  4. Cooling crude
Show answer & solution

Answer: (A) Removing light ends early to reduce furnace and column loads

It debottlenecks crude units.

Question 33

What is the function of a crude charge heater?

  1. Storing crude
  2. Cooling crude
  3. Separating water
  4. Heating crude to partially vaporise it before entering the column
Show answer & solution

Answer: (D) Heating crude to partially vaporise it before entering the column

It is a fired heater with radiant and convection sections.

Question 34

What is the effect of steam stripping on the flash point of side products?

  1. It removes heavy components
  2. It lowers the flash point
  3. It has no effect
  4. It raises the flash point by removing light components
Show answer & solution

Answer: (D) It raises the flash point by removing light components

Diesel and kerosene must meet minimum flash points.

Practice these 34 questions interactively →