What is the purpose of conversion processes in a refinery?
Show answer & solution
Answer: (D) Converting heavy, low-value fractions into lighter, higher-value products
Examples include FCC, hydrocracking and coking.
Chemical Engineering · Petroleum Refining & Natural Gas
35 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the purpose of conversion processes in a refinery?
Answer: (D) Converting heavy, low-value fractions into lighter, higher-value products
Examples include FCC, hydrocracking and coking.
What is fluid catalytic cracking (FCC)?
Answer: (B) Cracking heavy gas oil over a fluidised zeolite catalyst to produce gasoline and LPG
Catalyst circulates between riser reactor and regenerator.
Why is the FCC catalyst continuously regenerated?
Answer: (D) Coke deposited on the catalyst is burnt off, restoring activity and supplying heat for cracking
The regenerator operates at about 680–730 °C.
What is the role of the riser in an FCC unit?
Answer: (C) It is the main reaction zone where feed vaporises and cracks in seconds with hot catalyst
Contact time is about 2–5 s.
Why is FCC said to be in heat balance?
Answer: (A) Heat from burning coke in the regenerator supplies the endothermic cracking reaction
Coke yield adjusts to keep the balance.
What is hydrocracking?
Answer: (C) Cracking of heavy oils in the presence of hydrogen over a bifunctional catalyst at high pressure
It produces high-quality diesel and jet fuel.
What is the typical pressure range of hydrocracking units?
Answer: (C) About 100–200 bar
High hydrogen partial pressure suppresses coke.
What is catalytic reforming?
Answer: (A) Converting low-octane naphtha into high-octane reformate rich in aromatics, producing hydrogen
Platinum catalysts on chlorided alumina are used.
Which reactions in catalytic reforming produce most of the octane increase?
Answer: (D) Dehydrogenation of naphthenes to aromatics and dehydrocyclisation of paraffins
Dehydrogenation is strongly endothermic, so interheaters are used.
What is the important by-product of catalytic reforming?
Answer: (B) Hydrogen
It is used in hydrotreaters.
Why must reformer feed be hydrotreated?
Answer: (D) Sulphur, nitrogen and metals poison the platinum catalyst
Sulphur is reduced to below about 0.5 ppm.
What is continuous catalytic regeneration (CCR) reforming?
Answer: (A) Reforming in which catalyst moves continuously through reactors and a regenerator, allowing low pressure
Low pressure gives higher yields and octane.
What is isomerisation in a refinery?
Answer: (B) Converting straight-chain light paraffins (C₅–C₆) into branched isomers with higher octane
Light naphtha octane rises from about 70 to over 85.
What is alkylation in a refinery?
Answer: (C) Combining isobutane with light olefins to make high-octane branched paraffins
Sulphuric acid or HF catalysts are used.
What is visbreaking?
Answer: (A) Mild thermal cracking of residue to reduce its viscosity
It reduces cutter stock needed for fuel oil.
What is delayed coking?
Answer: (B) Severe thermal cracking of residue in drums to produce lighter products and petroleum coke
Drums alternate between filling and decoking.
What is the main use of needle (premium) coke?
Answer: (D) Making graphite electrodes for electric arc steel furnaces
Sponge coke is used as fuel and for anodes.
What is the main difference between thermal and catalytic cracking?
Answer: (C) Catalytic cracking proceeds by carbocation mechanisms giving more branched products and gasoline; thermal cracking by free radicals
Thermal cracking gives more olefins and gas.
What is the role of ZSM-5 additive in FCC?
Answer: (D) Increasing propylene yield and gasoline octane
It is a shape-selective zeolite.
What is the conversion in an FCC unit usually defined as?
Answer: (A) 100 minus the volume percent of products boiling above gasoline (light and heavy cycle oil)
Typical conversion is 70–80%.
What is residue fluid catalytic cracking (RFCC)?
Answer: (B) An FCC unit designed to process heavier feeds containing residue
It needs catalyst coolers and metal-tolerant catalyst.
What is solvent deasphalting?
Answer: (B) Using propane or butane to separate deasphalted oil from asphaltic residue
DAO is used for lubes or cracking feed.
What is polymerisation (cat poly) in a refinery?
Answer: (D) Combining light olefins into gasoline-range olefins over an acid catalyst
Phosphoric acid catalyst is used.
What is a deep conversion refinery?
Answer: (A) A refinery with residue upgrading units such as cokers or hydrocrackers that produce little fuel oil
Hydroskimming refineries produce much furnace oil.
What is a hydroskimming refinery?
Answer: (C) A refinery with crude distillation, reforming and hydrotreating but no major conversion units
Several older Pakistani refineries are of this type.
What is the typical octane number of reformate from a high-severity reformer?
Answer: (C) About 95–102 RON
High severity gives more aromatics and lower liquid yield.
Why is hydrogen important in modern refineries?
Answer: (A) It is needed for hydrotreating and hydrocracking to meet low-sulphur specifications
Steam methane reformers supplement reformer hydrogen.
What is the typical temperature of the FCC riser outlet?
Answer: (C) About 500–550 °C
Higher temperatures raise gas and olefin yields.
What is the catalyst-to-oil ratio in FCC?
Answer: (D) The mass ratio of circulating catalyst to oil feed, typically about 5–8
Higher ratios increase conversion.
What is light cycle oil (LCO)?
Answer: (A) A diesel-range product of FCC, rich in aromatics with low cetane
It is hydrotreated before blending into diesel.
What is the purpose of the HF alkylation acid regenerator?
Answer: (D) Removing polymers and water from the acid catalyst
HF is extremely hazardous, so sulphuric acid alkylation is often preferred.
What is the main product of alkylation?
Answer: (B) Alkylate, a high-octane, low-sulphur, aromatic-free gasoline component
It has RON about 92–96.
What is the main driver of the move toward deep conversion projects in Pakistani refineries?
Answer: (B) Falling demand for high-sulphur furnace oil and the need for Euro 5 fuels
Upgrade policies support refinery modernisation.
What is the main limitation of thermal cracking processes compared with catalytic cracking?
Answer: (C) Lower gasoline quality and higher yields of gas and coke
Thermal processes are used mainly for residue.
What is the product of the dehydrogenation of methylcyclohexane in catalytic reforming?
Answer: (D) Toluene
Naphthenes dehydrogenate to the corresponding aromatics.