What is a block flow diagram (BFD)?
Show answer & solution
Answer: (D) A simple diagram showing major process sections as blocks with main streams
It is used in early project stages.
Chemical Engineering · Process Equipment & Plant Design
44 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is a block flow diagram (BFD)?
Answer: (D) A simple diagram showing major process sections as blocks with main streams
It is used in early project stages.
What does a process flow diagram (PFD) show?
Answer: (A) Major equipment, main process streams, operating conditions and the material and energy balance
P&IDs add detailed piping and instrumentation.
What is a plot plan?
Answer: (B) A scaled drawing showing the location of equipment, buildings and roads within the plant site
It considers safety distances and maintenance access.
What is HAZOP?
Answer: (D) A structured study using guide words to identify hazards and operability problems in a design
Guide words include no, more, less, reverse and other than.
Which guide word in HAZOP would explore reverse flow in a line?
Answer: (A) Reverse
Each guide word is combined with a parameter such as flow.
What is a design basis document?
Answer: (B) A document that sets out capacity, feed and product specifications, site conditions and design standards
It is agreed before detailed design.
What is the onion model of process design?
Answer: (B) Design proceeds from the reactor outward to separation, heat recovery, utilities and finally safety and environment
Proposed by Smith and Linnhoff.
What is a common heuristic for sequencing distillation columns?
Answer: (A) Remove the most plentiful or corrosive components first and leave difficult separations to last
Direct sequences remove the lightest component first.
What is the main use of process simulators such as Aspen HYSYS or Aspen Plus?
Answer: (D) Steady-state and dynamic material and energy balances and equipment sizing
They contain property packages for phase equilibria.
Which property package is commonly selected in simulators for hydrocarbon and gas processing systems?
Answer: (C) Peng–Robinson equation of state
Activity models suit polar non-ideal liquids at low pressure.
What is scale-up?
Answer: (A) Translating a process from laboratory or pilot scale to full industrial scale
Similarity of geometry and dimensionless groups guides scale-up.
Why are pilot plants built before commercial plants?
Answer: (C) To test the process, obtain design data and reduce scale-up risk
They are especially important for new processes.
What is the purpose of equipment data sheets?
Answer: (D) To specify design conditions, materials and performance for vendors
Process and mechanical data sheets are prepared.
What is the purpose of a utility summary in plant design?
Answer: (B) To total steam, power, cooling water, fuel and other utility requirements for the plant
It sizes utility systems.
What site factors are considered when locating a chemical plant?
Answer: (B) Raw material and market access, utilities, transport, labour, climate and environmental rules
Many Pakistani fertiliser plants are located near gas fields or pipelines.
Why are fired heaters and flares located away from hydrocarbon storage in plant layout?
Answer: (C) They are ignition sources, so spacing reduces fire risk
Spacing guidelines come from codes and insurers.
What is the purpose of process safety management (PSM)?
Answer: (D) To prevent major accidents through systematic management of hazards, changes and procedures
Management of change is one element.
What is management of change (MOC)?
Answer: (A) A procedure to review and approve modifications before they are made, so new hazards are controlled
Many accidents have followed uncontrolled modifications.
What is HAZID?
Answer: (B) An early, broad hazard identification study of a project
HAZOP follows later in detailed design.
What is layer of protection analysis (LOPA)?
Answer: (D) A semi-quantitative method to check whether independent protection layers reduce risk enough
It helps assign SIL to safety functions.
What is the main purpose of an environmental impact assessment (EIA) for a new plant in Pakistan?
Answer: (C) To identify and mitigate environmental effects before approval by the environmental protection agency
EIA is required under the Pakistan Environmental Protection Act 1997 and provincial laws.
What is a pinch point in heat integration?
Answer: (A) The point of minimum temperature difference between hot and cold composite curves
No heat should cross the pinch for minimum utility use.
What is the main benefit of heat integration in plant design?
Answer: (A) Reduced external heating and cooling utility costs
Pinch analysis sets energy targets.
What is debottlenecking?
Answer: (D) Identifying and removing equipment or system limits to increase plant capacity
It is often cheaper than new capacity.
What is a turnkey project?
Answer: (C) A project in which a contractor designs, builds and commissions the plant and hands it over ready to operate
EPC contracts are similar.
What does EPC stand for in project execution?
Answer: (B) Engineering, procurement and construction
The EPC contractor delivers the complete plant.
What is commissioning?
Answer: (D) Bringing a newly built plant into operation by testing systems and starting up safely
Pre-commissioning includes flushing and pressure testing.
What is the purpose of an emergency shutdown (ESD) system?
Answer: (B) To isolate and depressurise the plant quickly in an emergency
ESD valves are fail-safe.
What is the main role of a dike (bund) around storage tanks?
Answer: (A) To contain spills and prevent spread of liquid in case of tank failure
Bund capacity is normally at least the largest tank volume plus margin.
What is the main purpose of a process description in design documents?
Answer: (A) To explain how the process works, step by step, for designers and operators
It accompanies the PFD.
What is the purpose of material and energy balances in design?
Answer: (C) To fix stream flows, compositions, temperatures and duties for equipment sizing
They are the foundation of the PFD.
What is a hazardous area classification?
Answer: (D) Defining zones where flammable atmospheres may occur so that suitable electrical equipment is selected
Zones 0, 1 and 2 follow IEC 60079.
In hazardous area classification for gases, what is Zone 1?
Answer: (A) An area where an explosive atmosphere is likely to occur in normal operation
Zone 0 is continuous and Zone 2 is abnormal and short-lived.
What is an explosion-proof (flameproof, Ex d) enclosure?
Answer: (B) An enclosure that contains an internal explosion and prevents it from igniting the surrounding atmosphere
Intrinsic safety (Ex i) limits energy instead.
What is the purpose of a quantitative risk assessment (QRA)?
Answer: (C) Estimating the likelihood and consequences of major accidents to evaluate risk numerically
It is used for siting decisions and layout.
What is the typical sequence of engineering stages in a project?
Answer: (D) Conceptual study, basic engineering (FEED), detailed engineering, procurement, construction and commissioning
FEED is front-end engineering design.
What is FEED in project engineering?
Answer: (B) Front-end engineering design that defines the project in enough detail for cost estimate and EPC tender
It reduces risk before major investment.
What is redundancy in plant design?
Answer: (A) Providing standby equipment, such as spare pumps, to maintain operation if one fails
Critical pumps are often installed as one running and one standby.
What is the purpose of a cause and effect matrix?
Answer: (D) To document which inputs trigger which shutdown or alarm actions in the safety system
It is used in ESD and fire and gas design.
What is a safety distance guideline between process units based on?
Answer: (C) Fire radiation, explosion overpressure and toxic release effects, as given by codes and insurers
Guidelines such as those from NFPA and industry are used.
What does the term inherent safety mean in design?
Answer: (A) Eliminating or reducing hazards at source, for example by smaller inventories or less hazardous materials
Principles include minimise, substitute, moderate and simplify.
Which inherent safety principle is applied when a large stock of a toxic intermediate is replaced by producing it as needed?
Answer: (C) Minimise (intensify)
The Bhopal disaster highlighted the danger of large inventories of methyl isocyanate.
What does the term design life mean for a plant?
Answer: (B) The period for which equipment is designed to operate safely with planned maintenance, often 20–25 years
Corrosion allowance and fatigue are based on design life.
What is a utility flow diagram?
Answer: (C) A diagram showing distribution of steam, water, air, nitrogen and other utilities
It complements the process PFD.