Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Process Equipment & Plant Design: Pressure Vessels and Tanks

Chemical Engineering · Process Equipment & Plant Design

42 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which code is most widely used for the design of unfired pressure vessels in process plants?

  1. IEC 60079
  2. ASME B31.3
  3. API 650
  4. ASME Boiler and Pressure Vessel Code, Section VIII
Show answer & solution

Answer: (D) ASME Boiler and Pressure Vessel Code, Section VIII

Division 1 uses design-by-rule and Division 2 design-by-analysis.

Question 2

What is the hoop (circumferential) stress in a thin cylindrical shell under internal pressure P with diameter D and thickness t?

  1. P/(Dt)
  2. PD/(2t)
  3. PD/t
  4. PD/(4t)
Show answer & solution

Answer: (B) PD/(2t)

It is twice the longitudinal stress.

Question 3

What is the longitudinal stress in a thin cylindrical shell under internal pressure?

  1. PD/(2t)
  2. PD/t
  3. PD/(4t)
  4. 2PD/t
Show answer & solution

Answer: (C) PD/(4t)

The circumferential seam carries this stress.

Question 4

Why does a thin cylinder under internal pressure usually fail along a longitudinal seam?

  1. Hoop stress, which acts on longitudinal seams, is twice the longitudinal stress
  2. Heads fail first always
  3. Longitudinal stress is larger
  4. Both stresses are zero
Show answer & solution

Answer: (A) Hoop stress, which acts on longitudinal seams, is twice the longitudinal stress

Longitudinal joints therefore need the higher efficiency.

Question 5

What is the stress in a thin spherical shell under internal pressure?

  1. PD/(2t)
  2. PD/(8t)
  3. PD/(4t)
  4. PD/t
Show answer & solution

Answer: (C) PD/(4t)

A sphere needs about half the thickness of a cylinder of the same diameter.

Question 6

What is the ASME Section VIII Division 1 formula for the thickness of a cylindrical shell under internal pressure?

  1. t = PR/(2SE + 0.2P)
  2. t = PR/(SE − 0.6P)
  3. t = PD/(4SE)
  4. t = P/(SE)
Show answer & solution

Answer: (B) t = PR/(SE − 0.6P)

R is inside radius, S allowable stress and E joint efficiency.

Question 7

What is the hoop stress in a vessel of 2 m diameter and 20 mm wall at an internal pressure of 2 MPa?

  1. 20 MPa
  2. 50 MPa
  3. 100 MPa
  4. 200 MPa
Show answer & solution

Answer: (C) 100 MPa

σ = 2 × 2,000/(2 × 20).

Question 8

What is weld joint efficiency in pressure vessel design?

  1. A factor that reduces allowable stress to account for the quality and inspection of welds
  2. The weld width
  3. The heat input of welding
  4. The welding speed
Show answer & solution

Answer: (A) A factor that reduces allowable stress to account for the quality and inspection of welds

Full radiography gives E = 1.0 for butt welds; spot radiography 0.85.

Question 9

What is the joint efficiency for a double-welded butt joint with no radiography under ASME VIII Division 1?

  1. 0.50
  2. 0.70
  3. 0.85
  4. 1.0
Show answer & solution

Answer: (B) 0.70

More inspection permits higher efficiency.

Question 10

What is a corrosion allowance?

  1. The allowable stress
  2. The hydrotest pressure
  3. The weld efficiency
  4. Extra wall thickness added to the calculated thickness to allow for metal loss over the design life
Show answer & solution

Answer: (D) Extra wall thickness added to the calculated thickness to allow for metal loss over the design life

Typical values for carbon steel are 1.5–3 mm.

Question 11

Which type of formed head needs the least thickness for a given pressure and diameter?

  1. Hemispherical head
  2. Flat head
  3. Conical head
  4. Torispherical head
Show answer & solution

Answer: (A) Hemispherical head

It needs about half the cylinder thickness.

Question 12

Which head type is most common for vessels operating at moderate pressures?

  1. Conical head
  2. Flat head
  3. Hemispherical head always
  4. 2:1 semi-ellipsoidal head
Show answer & solution

Answer: (D) 2:1 semi-ellipsoidal head

Its thickness is about equal to that of the shell.

Question 13

Why are flat heads limited to low-pressure or small-diameter vessels?

  1. They are too light
  2. They are difficult to fabricate
  3. They resist pressure by bending and need very large thickness
  4. They cannot be welded
Show answer & solution

Answer: (C) They resist pressure by bending and need very large thickness

Dished heads resist pressure mainly by membrane stress.

Question 14

What is the hydrostatic test pressure for vessels designed to current ASME Section VIII Division 1 rules?

  1. 1.3 times the maximum allowable working pressure, adjusted for temperature
  2. 3 times the design pressure
  3. Equal to the design pressure
  4. 1.5 times the operating pressure always
Show answer & solution

Answer: (A) 1.3 times the maximum allowable working pressure, adjusted for temperature

Older editions used 1.5 times.

Question 15

Why is water preferred to air for pressure testing vessels?

  1. Water is lighter
  2. Water stores little energy when compressed, so a failure is far less dangerous
  3. Water prevents corrosion always
  4. Air cannot be pressurised
Show answer & solution

Answer: (B) Water stores little energy when compressed, so a failure is far less dangerous

Pneumatic tests need special precautions.

Question 16

What is the maximum allowable working pressure (MAWP)?

  1. The normal operating pressure
  2. The relief valve blowdown pressure
  3. The hydrotest pressure
  4. The maximum gauge pressure permitted at the top of a vessel at its design temperature
Show answer & solution

Answer: (D) The maximum gauge pressure permitted at the top of a vessel at its design temperature

Relief valves are normally set at or below MAWP.

Question 17

How is design pressure usually chosen relative to maximum operating pressure?

  1. Equal to operating pressure
  2. Half the operating pressure
  3. Ten times the operating pressure
  4. About 10% (or a fixed margin) above the maximum operating pressure
Show answer & solution

Answer: (D) About 10% (or a fixed margin) above the maximum operating pressure

The margin avoids relief valve simmering in normal operation.

Question 18

What is the main failure mode to check for vessels under external pressure or vacuum?

  1. Buckling (elastic instability)
  2. Hoop stress yielding only
  3. Creep
  4. Erosion
Show answer & solution

Answer: (A) Buckling (elastic instability)

Stiffening rings increase resistance to buckling.

Question 19

Why are stiffening rings fitted to vacuum vessels?

  1. To support trays
  2. To reduce the unsupported length and increase resistance to buckling
  3. To increase internal pressure
  4. To reduce weight only
Show answer & solution

Answer: (B) To reduce the unsupported length and increase resistance to buckling

Vacuum columns and condensers use them.

Question 20

Which standard covers welded atmospheric steel storage tanks for oil?

  1. ASME Section VIII
  2. API 620 for high pressure
  3. API 650
  4. ASME B31.8
Show answer & solution

Answer: (C) API 650

It covers tanks with internal pressure up to about 2.5 psig.

Question 21

Which standard covers large low-pressure storage tanks above atmospheric limits, up to about 15 psig?

  1. API 610
  2. API 650
  3. ASME B16.5
  4. API 620
Show answer & solution

Answer: (D) API 620

Refrigerated LNG and LPG tanks are covered in its appendices.

Question 22

Why are floating roof tanks used for crude oil and gasoline storage?

  1. They hold higher pressure
  2. They are cheaper for water
  3. They reduce evaporation losses and vapour emissions by eliminating vapour space
  4. They store gases
Show answer & solution

Answer: (C) They reduce evaporation losses and vapour emissions by eliminating vapour space

Fixed roof tanks suit low-volatility liquids.

Question 23

How does shell thickness of a vertical atmospheric storage tank vary with height?

  1. It is greatest at the bottom course and decreases upward
  2. It is greatest at the top
  3. It is zero at the bottom
  4. It is uniform
Show answer & solution

Answer: (A) It is greatest at the bottom course and decreases upward

Hydrostatic pressure is highest at the bottom.

Question 24

What is the one-foot method in API 650?

  1. A method of roof design
  2. A method of calculating shell course thickness using hydrostatic head 0.3 m above the bottom of each course
  3. A method of foundation design
  4. A testing method
Show answer & solution

Answer: (B) A method of calculating shell course thickness using hydrostatic head 0.3 m above the bottom of each course

It applies to tanks up to about 60 m diameter.

Question 25

How are LPG and propane commonly stored at ambient temperature?

  1. In wooden tanks
  2. In open pits
  3. In pressure vessels such as spheres or horizontal bullets
  4. In floating roof tanks
Show answer & solution

Answer: (C) In pressure vessels such as spheres or horizontal bullets

Large quantities may be stored refrigerated.

Question 26

What is the main purpose of a vessel skirt?

  1. To support a tall vertical vessel such as a column on its foundation
  2. To insulate the vessel
  3. To strengthen the head
  4. To carry nozzles
Show answer & solution

Answer: (A) To support a tall vertical vessel such as a column on its foundation

Saddles support horizontal vessels.

Question 27

Which supports are commonly used for horizontal drums and heat exchangers?

  1. Skirts
  2. Saddle supports
  3. Brackets only
  4. Legs only
Show answer & solution

Answer: (B) Saddle supports

Two saddles are normally used.

Question 28

Which loads must be considered for tall columns besides pressure?

  1. Only colour of paint
  2. Only internal pressure
  3. Only temperature
  4. Wind and seismic loads, dead weight and loads from piping
Show answer & solution

Answer: (D) Wind and seismic loads, dead weight and loads from piping

Pakistan's seismic zones are given in the Building Code of Pakistan.

Question 29

What is the purpose of nozzle reinforcement pads?

  1. To support trays
  2. To protect insulation
  3. To compensate for the metal removed by openings in the shell
  4. To carry instruments
Show answer & solution

Answer: (C) To compensate for the metal removed by openings in the shell

Area replacement rules are given in the code.

Question 30

What is the purpose of a manhole on a vessel?

  1. To allow entry for inspection, maintenance and installation of internals
  2. To vent gases
  3. To drain liquid
  4. To measure level
Show answer & solution

Answer: (A) To allow entry for inspection, maintenance and installation of internals

A typical minimum size is about 18–24 inches.

Question 31

What does post-weld heat treatment (PWHT) achieve?

  1. It removes corrosion allowance
  2. It increases hardness only
  3. It increases design pressure
  4. It relieves residual welding stresses and improves toughness of the weld zone
Show answer & solution

Answer: (D) It relieves residual welding stresses and improves toughness of the weld zone

It is required for thick sections and some services.

Question 32

What is the purpose of impact (Charpy) testing of vessel steel?

  1. To measure tensile strength
  2. To ensure adequate toughness against brittle fracture at low temperatures
  3. To measure hardness
  4. To check corrosion
Show answer & solution

Answer: (B) To ensure adequate toughness against brittle fracture at low temperatures

The minimum design metal temperature governs requirements.

Question 33

What is the typical length-to-diameter ratio of an economic pressure vessel?

  1. About 0.5
  2. About 3 to 5
  3. About 20
  4. About 100
Show answer & solution

Answer: (B) About 3 to 5

Higher pressures favour longer, narrower vessels.

Question 34

Which vessel material is widely used for general non-corrosive service at moderate temperatures?

  1. Lead
  2. Titanium
  3. Carbon steel plate such as SA-516 Grade 70
  4. Copper
Show answer & solution

Answer: (C) Carbon steel plate such as SA-516 Grade 70

SA-516 is a pressure vessel quality steel.

Question 35

What is the maximum allowable stress for SA-516 Grade 70 at moderate temperatures under ASME VIII Division 1, approximately?

  1. About 20 MPa
  2. About 138 MPa (20,000 psi)
  3. About 500 MPa
  4. About 1,000 MPa
Show answer & solution

Answer: (B) About 138 MPa (20,000 psi)

Allowable stress falls at high temperature.

Question 36

What is the required shell thickness, excluding corrosion allowance, for P = 1 MPa, inside radius 1,000 mm, S = 138 MPa and E = 1, using t = PR/(SE − 0.6P)?

  1. About 1 mm
  2. About 3.6 mm
  3. About 7.3 mm
  4. About 14.5 mm
Show answer & solution

Answer: (C) About 7.3 mm

t = 1 × 1,000/(138 − 0.6).

Question 37

What is the purpose of a vessel's nameplate?

  1. To show the owner's name only
  2. To decorate the vessel
  3. To show product prices
  4. To record design code, MAWP, design temperature, serial number and test details
Show answer & solution

Answer: (D) To record design code, MAWP, design temperature, serial number and test details

It is required by the code.

Question 38

What is a jacketed vessel?

  1. A vessel with an outer shell for circulating heating or cooling fluid
  2. A vessel with insulation only
  3. A vessel with no openings
  4. A spherical tank
Show answer & solution

Answer: (A) A vessel with an outer shell for circulating heating or cooling fluid

Half-pipe coils are an alternative.

Question 39

Why are spheres used for storing large volumes of gases under pressure?

  1. Spheres are cheapest to fabricate
  2. Spheres need no supports
  3. Spheres hold atmospheric liquids best
  4. A sphere has the lowest surface area and thinnest wall for a given volume and pressure
Show answer & solution

Answer: (D) A sphere has the lowest surface area and thinnest wall for a given volume and pressure

LPG and butane are stored in spheres.

Question 40

What is the function of a breather (pressure–vacuum) valve on a fixed-roof tank?

  1. To measure level
  2. To protect the tank from overpressure and vacuum during filling, emptying and temperature changes
  3. To drain water
  4. To heat the tank
Show answer & solution

Answer: (B) To protect the tank from overpressure and vacuum during filling, emptying and temperature changes

API 2000 covers tank venting.

Question 41

What is the purpose of tank bottom water draw-off?

  1. To measure density
  2. To remove water that settles out of stored oil
  3. To add water
  4. To heat oil
Show answer & solution

Answer: (B) To remove water that settles out of stored oil

Water accumulates at the bottom of crude tanks.

Question 42

What does radiography of welds detect?

  1. Internal defects such as porosity, slag inclusions and lack of fusion
  2. Hardness
  3. Chemical composition only
  4. Surface paint thickness
Show answer & solution

Answer: (A) Internal defects such as porosity, slag inclusions and lack of fusion

Ultrasonic testing is an alternative.

Practice these 42 questions interactively →