Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Process Equipment & Plant Design: Equipment Sizing

Chemical Engineering · Process Equipment & Plant Design

42 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What does the Souders–Brown equation give in column and separator design?

  1. The heat duty
  2. The liquid level
  3. The pressure drop
  4. The maximum allowable vapour velocity u = K√((ρL − ρV)/ρV)
Show answer & solution

Answer: (D) The maximum allowable vapour velocity u = K√((ρL − ρV)/ρV)

K depends on tray spacing or demister type.

Question 2

How is the diameter of a distillation column found?

  1. From the reflux drum size
  2. From the vapour flow rate and an allowable vapour velocity below flooding
  3. From the number of trays
  4. From the feed temperature only
Show answer & solution

Answer: (B) From the vapour flow rate and an allowable vapour velocity below flooding

Design is often at 70–85% of flooding.

Question 3

What is a typical tray spacing in distillation columns?

  1. About 0.05 m
  2. About 0.45 to 0.6 m
  3. About 2 m
  4. About 5 m
Show answer & solution

Answer: (B) About 0.45 to 0.6 m

Larger spacing allows higher vapour velocity.

Question 4

How many actual trays are needed if 15 theoretical stages (excluding reboiler) are required and tray efficiency is 60%?

  1. 9
  2. 15
  3. 25
  4. 30
Show answer & solution

Answer: (C) 25

15/0.6.

Question 5

What is the approximate height of a column with 25 trays at 0.6 m spacing, plus 3 m for top and bottom space?

  1. 12 m
  2. 15 m
  3. 18 m
  4. 21 m
Show answer & solution

Answer: (C) 18 m

25 × 0.6 + 3.

Question 6

What is the typical liquid residence time used for sizing reflux drums and separators?

  1. About 1 day
  2. About 5 seconds
  3. About 5 to 10 minutes of hold-up
  4. About 10 hours
Show answer & solution

Answer: (C) About 5 to 10 minutes of hold-up

Hold-up absorbs upsets and gives time for operators to respond.

Question 7

What is a demister (mist eliminator) used for in separators?

  1. Removing fine liquid droplets from the gas leaving a separator
  2. Removing solids
  3. Measuring level
  4. Heating gas
Show answer & solution

Answer: (A) Removing fine liquid droplets from the gas leaving a separator

Wire mesh pads are common.

Question 8

What is the main difference between a horizontal and a vertical separator?

  1. Horizontal separators cannot have demisters
  2. Vertical separators handle more liquid always
  3. They are the same
  4. Horizontal separators suit high liquid loads; vertical ones suit high gas-to-liquid ratios and small plot area
Show answer & solution

Answer: (D) Horizontal separators suit high liquid loads; vertical ones suit high gas-to-liquid ratios and small plot area

Three-phase separation favours horizontal vessels.

Question 9

What is a three-phase separator used for in oil and gas production?

  1. Drying gas
  2. Separating solids from gas
  3. Distilling crude
  4. Separating gas, oil and water
Show answer & solution

Answer: (D) Separating gas, oil and water

Weirs and boots collect water.

Question 10

What standard tube outside diameters are common in shell and tube exchangers?

  1. 1 m
  2. 5 mm
  3. 19.05 mm (3/4 inch) and 25.4 mm (1 inch)
  4. 200 mm
Show answer & solution

Answer: (C) 19.05 mm (3/4 inch) and 25.4 mm (1 inch)

Standard tube lengths are 8, 12, 16 and 20 ft.

Question 11

What is a common overdesign factor added to calculated equipment capacity?

  1. 0%
  2. About 10 to 20%
  3. About 200%
  4. About 1,000%
Show answer & solution

Answer: (B) About 10 to 20%

It covers uncertainties in data and future capacity.

Question 12

What is the heat transfer area per tube for a 25.4 mm OD tube 6 m long?

  1. About 0.048 m²
  2. About 0.48 m²
  3. About 1.5 m²
  4. About 4.8 m²
Show answer & solution

Answer: (B) About 0.48 m²

A = πDL = π × 0.0254 × 6.

Question 13

What does pump selection mainly depend on?

  1. Flow rate, head, fluid properties and NPSH available
  2. Pipe length only
  3. Pump colour
  4. Motor brand
Show answer & solution

Answer: (A) Flow rate, head, fluid properties and NPSH available

Centrifugal pumps are chosen for most clean liquid duties.

Question 14

Which standard covers centrifugal pumps for petroleum, petrochemical and gas industries?

  1. API 650
  2. ASME B31.3
  3. API 520
  4. API 610
Show answer & solution

Answer: (D) API 610

It specifies heavy-duty construction.

Question 15

What is the hydraulic power of a pump delivering 50 m³/h against 40 m head of water?

  1. About 0.55 kW
  2. About 2.7 kW
  3. About 5.45 kW
  4. About 54.5 kW
Show answer & solution

Answer: (C) About 5.45 kW

P = ρgQH = 1,000 × 9.81 × (50/3,600) × 40.

Question 16

How is the volume of a reactor sized from production rate?

  1. From residence time needed for the required conversion and the volumetric throughput
  2. From the pressure only
  3. From the colour of product
  4. From pipe size
Show answer & solution

Answer: (A) From residence time needed for the required conversion and the volumetric throughput

V = τ × volumetric flow for continuous reactors.

Question 17

What is the purpose of a surge (buffer) tank between process units?

  1. To increase pressure
  2. To heat liquid
  3. To separate gases
  4. To absorb flow fluctuations and decouple upstream and downstream units
Show answer & solution

Answer: (D) To absorb flow fluctuations and decouple upstream and downstream units

Averaging level control uses its capacity.

Question 18

What is the working volume of a storage tank usually taken as?

  1. 10%
  2. 50%
  3. About 80–90% of the total volume, leaving space for expansion and vapour
  4. 100%
Show answer & solution

Answer: (C) About 80–90% of the total volume, leaving space for expansion and vapour

Safe filling limits prevent overflow.

Question 19

What is the purpose of a flare system?

  1. Safe disposal of relief and vent gases by combustion
  2. Measuring flow
  3. Generating steam
  4. Storing gas
Show answer & solution

Answer: (A) Safe disposal of relief and vent gases by combustion

Flare design follows API 521.

Question 20

What determines the height and position of a flare stack?

  1. Tank shape
  2. Allowable radiant heat intensity at ground level and on personnel
  3. Plant colour
  4. Pipe schedule
Show answer & solution

Answer: (B) Allowable radiant heat intensity at ground level and on personnel

API 521 gives radiation limits.

Question 21

What does a knock-out drum before a flare do?

  1. Removes liquid from relief gases before they reach the flare
  2. Cools gas only
  3. Measures gas flow
  4. Ignites gas
Show answer & solution

Answer: (A) Removes liquid from relief gases before they reach the flare

Liquid carry-over can cause burning rain.

Question 22

What is the typical approach temperature in cooling water exchangers?

  1. About 0.1 °C
  2. About 5–10 °C
  3. About 50 °C
  4. About 100 °C
Show answer & solution

Answer: (B) About 5–10 °C

Small approaches require large areas.

Question 23

What is the typical design cooling water supply temperature in hot climates such as in Pakistan?

  1. About 0 °C
  2. About 5 °C
  3. About 32–35 °C
  4. About 60 °C
Show answer & solution

Answer: (C) About 32–35 °C

It depends on the ambient wet bulb temperature at the cooling tower.

Question 24

What does packing height for an absorber equal?

  1. Liquid flow/gas flow
  2. Diameter × 2
  3. Number of trays × spacing
  4. HTU × NTU (or HETP × number of stages)
Show answer & solution

Answer: (D) HTU × NTU (or HETP × number of stages)

Additional height is added for distributors and supports.

Question 25

What is the maximum allowable vapour velocity in a separator if K = 0.1 m/s, ρL = 800 kg/m³ and ρV = 8 kg/m³?

  1. About 0.1 m/s
  2. About 0.995 m/s
  3. About 9.95 m/s
  4. About 10 m/s
Show answer & solution

Answer: (B) About 0.995 m/s

u = 0.1 × √(792/8) = 0.1 × 9.95.

Question 26

What is the cross-sectional area needed for 2 m³/s of vapour at an allowable velocity of 1 m/s?

  1. 0.5 m²
  2. 1 m²
  3. 2 m²
  4. 4 m²
Show answer & solution

Answer: (C) 2 m²

A = Q/u.

Question 27

What is the column diameter for a required cross-sectional area of 3.14 m²?

  1. 1 m
  2. 2 m
  3. 3.14 m
  4. 4 m
Show answer & solution

Answer: (B) 2 m

D = √(4A/π).

Question 28

What is the downcomer area of a tray typically as a fraction of column area?

  1. About 1%
  2. About 10–15%
  3. About 50%
  4. About 90%
Show answer & solution

Answer: (B) About 10–15%

It must handle liquid flow without backing up.

Question 29

What is the typical weir height on sieve trays in atmospheric columns?

  1. About 1 m
  2. About 2 mm
  3. About 40–90 mm
  4. About 500 mm
Show answer & solution

Answer: (C) About 40–90 mm

Lower weirs are used in vacuum service.

Question 30

What is the typical hole area of a sieve tray as a fraction of active area?

  1. About 0.1%
  2. About 5–15%
  3. About 50%
  4. About 90%
Show answer & solution

Answer: (B) About 5–15%

Hole diameters are usually 3–12 mm.

Question 31

What is turndown ratio for a tray column?

  1. The reflux ratio
  2. The number of trays
  3. The tray spacing
  4. The ratio of maximum to minimum vapour rates for satisfactory operation
Show answer & solution

Answer: (D) The ratio of maximum to minimum vapour rates for satisfactory operation

Valve trays offer better turndown than sieve trays.

Question 32

Why are packed columns preferred to tray columns for small diameters below about 0.6 m?

  1. Trays are difficult to install and maintain in small columns, and packing is cheaper
  2. Packing cannot be used in large columns
  3. Trays work only in small columns
  4. Packed columns are always more efficient
Show answer & solution

Answer: (A) Trays are difficult to install and maintain in small columns, and packing is cheaper

Packed columns also suit corrosive and foaming service.

Question 33

Why are tray columns preferred when liquid contains solids or tends to foul?

  1. Trays have lower pressure drop
  2. Trays are cheaper always
  3. Trays are easier to clean and less prone to plugging than random packing
  4. Packing handles solids better
Show answer & solution

Answer: (C) Trays are easier to clean and less prone to plugging than random packing

Large-diameter columns also often use trays.

Question 34

What is the typical pressure drop per tray in atmospheric distillation?

  1. About 0.001 kPa
  2. About 0.5–1 kPa
  3. About 10 kPa
  4. About 50 kPa
Show answer & solution

Answer: (B) About 0.5–1 kPa

Vacuum columns need low-pressure-drop internals.

Question 35

What is the main criterion for choosing tube-side versus shell-side for cooling water?

  1. Cooling water usually goes in tubes for easy cleaning and better velocity control
  2. Cooling water always goes on the shell side
  3. The cleanest fluid always goes in tubes
  4. There is no rule
Show answer & solution

Answer: (A) Cooling water usually goes in tubes for easy cleaning and better velocity control

Fouling fluids go where cleaning is easiest.

Question 36

What is a typical tube-side velocity for liquids in heat exchangers?

  1. About 0.01 m/s
  2. About 1–3 m/s
  3. About 30 m/s
  4. About 100 m/s
Show answer & solution

Answer: (B) About 1–3 m/s

Higher velocities reduce fouling but raise pressure drop.

Question 37

How many tubes 6 m long and 25.4 mm OD are needed for 48 m² of heat transfer area?

  1. About 10
  2. About 48
  3. About 100
  4. About 1,000
Show answer & solution

Answer: (C) About 100

Each tube has about 0.48 m².

Question 38

What is the typical allowable pressure drop for liquids in a heat exchanger?

  1. About 1 Pa
  2. About 2 MPa
  3. About 10 MPa
  4. About 35–70 kPa
Show answer & solution

Answer: (D) About 35–70 kPa

Gas-side allowances are lower.

Question 39

What is the purpose of a vortex breaker in a vessel outlet nozzle?

  1. To prevent vortex formation that draws gas into the pump suction
  2. To mix liquids
  3. To measure level
  4. To increase flow
Show answer & solution

Answer: (A) To prevent vortex formation that draws gas into the pump suction

It protects pumps from cavitation and gas entrainment.

Question 40

What is the typical economic L/D ratio for a horizontal separator?

  1. About 0.5
  2. About 1
  3. About 3 to 5
  4. About 20
Show answer & solution

Answer: (C) About 3 to 5

Very long vessels are costly to support.

Question 41

What is the typical holding time used for sizing a feed surge drum?

  1. About 1 hour per tray
  2. About 2 days
  3. About 10 seconds
  4. About 10–20 minutes of feed flow
Show answer & solution

Answer: (D) About 10–20 minutes of feed flow

It allows downstream units to ride through upsets.

Question 42

What is the typical minimum NPSH margin recommended between NPSH available and NPSH required for process pumps?

  1. A negative margin of about 1 m
  2. About 0.6–1 m or 10–35%, depending on the service
  3. Zero
  4. About 50 m
Show answer & solution

Answer: (B) About 0.6–1 m or 10–35%, depending on the service

A margin protects against cavitation from transient conditions.

Practice these 42 questions interactively →