Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Process Equipment & Plant Design: Piping and Fittings

Chemical Engineering · Process Equipment & Plant Design

39 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Which code is used for process piping in refineries and chemical plants?

  1. ASME B31.3
  2. ASME B31.8
  3. ASME B31.1
  4. API 650
Show answer & solution

Answer: (A) ASME B31.3

B31.1 covers power piping and B31.8 gas transmission pipelines.

Question 2

Which code is used for gas transmission and distribution pipelines such as those of SNGPL and SSGC?

  1. ASME Section VIII
  2. API 620
  3. ASME B31.3
  4. ASME B31.8
Show answer & solution

Answer: (D) ASME B31.8

Pipeline design class depends on location and population density.

Question 3

What does nominal pipe size (NPS) indicate?

  1. The pressure rating
  2. The exact inside diameter
  3. A standard size designation that is not exactly equal to the actual diameter for small pipes
  4. The wall thickness
Show answer & solution

Answer: (C) A standard size designation that is not exactly equal to the actual diameter for small pipes

Outside diameter is fixed for each NPS; wall thickness varies with schedule.

Question 4

What does a higher pipe schedule number indicate for the same NPS?

  1. A thinner wall
  2. A lower pressure rating
  3. A larger outside diameter
  4. A thicker wall and smaller inside diameter
Show answer & solution

Answer: (D) A thicker wall and smaller inside diameter

Schedule 40 and 80 are common.

Question 5

What is the approximate relation for pipe schedule number?

  1. Schedule ≈ 1000 P/S, with P internal pressure and S allowable stress in the same units
  2. Schedule = P × S
  3. Schedule = D/t
  4. Schedule = 1000/P
Show answer & solution

Answer: (A) Schedule ≈ 1000 P/S, with P internal pressure and S allowable stress in the same units

It is an approximate guide to wall thickness.

Question 6

Which ASME standard covers steel pipe flanges and flanged fittings up to NPS 24?

  1. ASME B31.3
  2. ASME B16.5
  3. API 6D
  4. ASME B16.9
Show answer & solution

Answer: (B) ASME B16.5

Pressure classes are 150, 300, 600, 900, 1500 and 2500.

Question 7

What does a flange pressure class such as Class 300 indicate?

  1. A thickness of 300 mm
  2. A pressure–temperature rating group; the allowable pressure falls as temperature rises
  3. A size of 300 mm
  4. A fixed pressure of 300 psi at all temperatures
Show answer & solution

Answer: (B) A pressure–temperature rating group; the allowable pressure falls as temperature rises

Ratings depend on material group.

Question 8

Which flange type is preferred for high pressure and high temperature service?

  1. Weld neck flange
  2. Lap joint flange
  3. Threaded flange
  4. Slip-on flange
Show answer & solution

Answer: (A) Weld neck flange

Its tapered hub reduces stress concentration.

Question 9

Which gasket type is widely used for high-pressure flanges in hydrocarbon service?

  1. Rubber sheet
  2. Paper
  3. Spiral wound gasket with metal winding and graphite or PTFE filler
  4. Cork
Show answer & solution

Answer: (C) Spiral wound gasket with metal winding and graphite or PTFE filler

Ring-type joints are used for very high pressures.

Question 10

Why are expansion loops or bellows provided in long hot pipelines?

  1. To reduce pressure
  2. To trap condensate
  3. To increase flow
  4. To absorb thermal expansion and prevent excessive stresses
Show answer & solution

Answer: (D) To absorb thermal expansion and prevent excessive stresses

Steel expands about 1.2 mm per metre per 100 °C.

Question 11

What is the approximate thermal expansion of a 100 m carbon steel pipe heated by 100 °C?

  1. About 1.2 mm
  2. About 12 mm
  3. About 120 mm
  4. About 1,200 mm
Show answer & solution

Answer: (C) About 120 mm

α ≈ 12 × 10⁻⁶ per K.

Question 12

What is the purpose of pipe supports and hangers?

  1. To insulate pipes
  2. To carry pipe weight and control movement and vibration
  3. To measure pressure
  4. To increase flow
Show answer & solution

Answer: (B) To carry pipe weight and control movement and vibration

Spring hangers accommodate vertical movement.

Question 13

What is the purpose of a steam trap on a steam line?

  1. To remove condensate while preventing steam loss
  2. To relieve overpressure
  3. To control steam pressure
  4. To measure steam flow
Show answer & solution

Answer: (A) To remove condensate while preventing steam loss

Drip legs collect condensate ahead of traps.

Question 14

What is the purpose of a strainer upstream of a pump?

  1. To control flow
  2. To cool the pump
  3. To measure pressure
  4. To protect the pump from debris
Show answer & solution

Answer: (D) To protect the pump from debris

Temporary strainers are used during commissioning.

Question 15

Which valve is mainly used for full-open or full-closed isolation with low pressure drop?

  1. Gate valve
  2. Pressure regulator
  3. Needle valve
  4. Globe valve
Show answer & solution

Answer: (A) Gate valve

Ball valves are also common for isolation.

Question 16

Which valve gives quick quarter-turn operation and tight shut-off?

  1. Check valve
  2. Ball valve
  3. Globe valve
  4. Gate valve
Show answer & solution

Answer: (B) Ball valve

Plug valves also turn 90°.

Question 17

What is a blind (spectacle) flange used for?

  1. Relieving pressure
  2. Throttling flow
  3. Measuring flow
  4. Positive isolation of equipment for maintenance
Show answer & solution

Answer: (D) Positive isolation of equipment for maintenance

Spades and spectacle blinds ensure no leakage into isolated equipment.

Question 18

What is the purpose of a pipe slope in drain and condensate lines?

  1. To support the pipe
  2. To increase pressure
  3. To allow gravity drainage and prevent liquid accumulation
  4. To decrease flow area
Show answer & solution

Answer: (C) To allow gravity drainage and prevent liquid accumulation

Steam lines slope toward drip points.

Question 19

What is a reducer used for in piping?

  1. To isolate flow
  2. To join pipes at an angle
  3. To close the end of a pipe
  4. To connect pipes of different diameters
Show answer & solution

Answer: (D) To connect pipes of different diameters

Eccentric reducers are used at pump suctions to avoid vapour pockets.

Question 20

Why are eccentric reducers installed flat side up at pump suctions?

  1. To prevent pump rotation
  2. To increase suction pressure
  3. To prevent air or vapour pockets that could cause cavitation
  4. To reduce cost
Show answer & solution

Answer: (C) To prevent air or vapour pockets that could cause cavitation

Concentric reducers are used on vertical lines.

Question 21

What is the typical maximum velocity for steam in process piping?

  1. About 0.1 m/s
  2. About 1 m/s
  3. About 25 to 40 m/s
  4. About 200 m/s
Show answer & solution

Answer: (C) About 25 to 40 m/s

Higher velocities cause noise and erosion.

Question 22

What is a line list in plant design?

  1. A list of all pipelines with their sizes, fluids, design conditions, materials and insulation
  2. A list of instruments only
  3. A list of staff
  4. A list of equipment
Show answer & solution

Answer: (A) A list of all pipelines with their sizes, fluids, design conditions, materials and insulation

It is produced from the P&ID.

Question 23

What is a piping class (specification)?

  1. A calculation of flow
  2. A document defining pipe, fittings, flanges, valves and gaskets permitted for a service and rating
  3. A drawing of supports
  4. A list of pipe colours
Show answer & solution

Answer: (B) A document defining pipe, fittings, flanges, valves and gaskets permitted for a service and rating

Each line is assigned a piping class.

Question 24

What is pipe stress analysis used for?

  1. Selecting valves
  2. Checking that thermal, weight and pressure loads do not overstress piping or equipment nozzles
  3. Calculating pressure drop
  4. Sizing pumps
Show answer & solution

Answer: (B) Checking that thermal, weight and pressure loads do not overstress piping or equipment nozzles

Software such as CAESAR II is commonly used.

Question 25

What is a hot tap?

  1. A tap for hot water
  2. A pipe heater
  3. A drain valve
  4. Connecting to a pipeline while it remains in service
Show answer & solution

Answer: (D) Connecting to a pipeline while it remains in service

It requires strict procedures.

Question 26

Which pipe joining method is common for small-bore piping below about 2 inches?

  1. Socket weld or threaded joints
  2. Flanged only
  3. Butt weld only
  4. Bolted bellows
Show answer & solution

Answer: (A) Socket weld or threaded joints

Butt welding is common for larger sizes.

Question 27

What does an ASME B16.9 standard cover?

  1. Valves
  2. Pressure vessels
  3. Flanges
  4. Factory-made wrought butt-welding fittings such as elbows, tees and reducers
Show answer & solution

Answer: (D) Factory-made wrought butt-welding fittings such as elbows, tees and reducers

Long-radius elbows have radius 1.5 times NPS.

Question 28

What is the purpose of insulation on cold lines such as refrigerant lines?

  1. To heat the fluid
  2. To reduce pipe weight
  3. To reduce heat gain and prevent condensation and icing
  4. To protect from fire only
Show answer & solution

Answer: (C) To reduce heat gain and prevent condensation and icing

A vapour barrier is essential on cold insulation.

Question 29

What is personnel protection insulation?

  1. Insulation applied to hot surfaces mainly to prevent burns
  2. Fireproofing
  3. Acoustic lining
  4. Insulation to save energy only
Show answer & solution

Answer: (A) Insulation applied to hot surfaces mainly to prevent burns

It is used where surfaces exceed about 60 °C within reach.

Question 30

What is the minimum pipe wall thickness under ASME B31.3 for internal pressure?

  1. t = SE/P
  2. t = P/D
  3. t = PD/S
  4. t = PD/(2(SE + PY)), plus allowances for corrosion and threads
Show answer & solution

Answer: (D) t = PD/(2(SE + PY)), plus allowances for corrosion and threads

Y is a coefficient, 0.4 for ferritic steels below 482 °C.

Question 31

What is the typical hydrostatic test pressure for process piping under ASME B31.3?

  1. Equal to design pressure
  2. 1.1 times operating pressure
  3. 3 times design pressure
  4. 1.5 times the design pressure, adjusted for temperature
Show answer & solution

Answer: (D) 1.5 times the design pressure, adjusted for temperature

Pneumatic tests use 1.1 times design pressure.

Question 32

What is a bypass around a control valve used for?

  1. Allowing manual flow control while the valve is isolated for maintenance
  2. Relieving pressure
  3. Measuring flow
  4. Increasing flow permanently
Show answer & solution

Answer: (A) Allowing manual flow control while the valve is isolated for maintenance

Block valves isolate the control valve.

Question 33

What is the function of a vent and drain on piping?

  1. Increasing pressure
  2. Supporting pipes
  3. Measuring flow
  4. Venting air during filling and draining liquid during maintenance
Show answer & solution

Answer: (D) Venting air during filling and draining liquid during maintenance

High-point vents and low-point drains are standard.

Question 34

What is a pipe rack?

  1. A pipe-bending machine
  2. A support for one pump
  3. A structure carrying many pipelines and cables between plant areas
  4. A storage shelf for spare pipes
Show answer & solution

Answer: (C) A structure carrying many pipelines and cables between plant areas

Pipe racks form the backbone of a plant layout.

Question 35

What colour coding helps identify pipeline contents in plants?

  1. Standard colour bands and labels for steam, water, air, gas and chemicals
  2. Only white
  3. Only black
  4. Random colours
Show answer & solution

Answer: (A) Standard colour bands and labels for steam, water, air, gas and chemicals

Codes such as ISO 14726 and company standards are used.

Question 36

What is an isometric drawing in piping?

  1. A P&ID
  2. A process flow diagram
  3. A plot plan
  4. A three-dimensional representation of a pipe line used for fabrication and installation
Show answer & solution

Answer: (D) A three-dimensional representation of a pipe line used for fabrication and installation

It shows dimensions, fittings and welds.

Question 37

Why are long-radius elbows preferred to short-radius elbows?

  1. They change flow direction by 180°
  2. They are shorter
  3. They give lower pressure drop and less erosion
  4. They are always cheaper
Show answer & solution

Answer: (C) They give lower pressure drop and less erosion

Short-radius elbows save space.

Question 38

What is the function of a pressure-reducing valve in a steam system?

  1. To reduce steam pressure to a lower header pressure for users
  2. To raise pressure
  3. To relieve overpressure
  4. To stop flow
Show answer & solution

Answer: (A) To reduce steam pressure to a lower header pressure for users

Safety valves protect downstream equipment.

Question 39

What is the purpose of tracing (steam or electric) on pipelines?

  1. To measure flow
  2. To keep fluids warm to prevent freezing, solidification or high viscosity
  3. To support pipes
  4. To cool fluids
Show answer & solution

Answer: (B) To keep fluids warm to prevent freezing, solidification or high viscosity

Heavy fuel oil lines are commonly traced.

Practice these 39 questions interactively →