What are parallel (competing) reactions?
Show answer & solution
Answer: (D) Reactions in which a reactant forms different products by separate paths
A → R and A → S is an example.
Chemical Engineering · Chemical Reaction Engineering
32 questions, each with the answer and a worked solution.
Practice interactively and track your score →What are parallel (competing) reactions?
Answer: (D) Reactions in which a reactant forms different products by separate paths
A → R and A → S is an example.
What are series (consecutive) reactions?
Answer: (A) Reactions in which a product reacts further to form another product
A → R → S is an example.
For parallel reactions A → R (order a₁) and A → S (order a₂), how is formation of R favoured if a₁ > a₂?
Answer: (D) By keeping the concentration of A high
A PFR or batch reactor keeps concentration high.
For parallel reactions where the desired reaction has a lower order, which reactor is preferred?
Answer: (A) CSTR, which keeps reactant concentration low
Dilution also helps.
For parallel reactions where the desired reaction has the higher activation energy, what temperature is preferred?
Answer: (D) High temperature
Higher temperature favours the reaction with higher activation energy.
In the series reaction A → R → S, where R is desired, what happens to the concentration of R in a batch reactor with time?
Answer: (B) It rises to a maximum and then falls
The batch must be stopped at the optimum time.
For A → R → S with first-order steps and k₁ = k₂ = k, at what time does R reach its maximum in a batch reactor?
Answer: (A) t = 1/k
In general tmax = ln(k₂/k₁)/(k₂ − k₁).
Which reactor generally gives the higher maximum yield of an intermediate R in A → R → S?
Answer: (C) PFR or batch reactor
Mixing products with fresh feed lowers yield.
What is instantaneous fractional yield?
Answer: (D) The rate of formation of the desired product divided by the rate of consumption of the reactant
Overall yield is the average over the reactor.
What is the overall selectivity?
Answer: (B) The ratio of moles of desired product formed to moles of undesired product formed
Definitions should be stated clearly.
How can selectivity to an intermediate in series reactions be improved?
Answer: (A) By operating at low conversion and recycling unreacted feed
Low conversion reduces further reaction of the intermediate.
Why is ethylene oxide production by partial oxidation of ethylene run at low conversion per pass?
Answer: (B) To limit further oxidation of the product and ethylene to CO₂ and water
Unreacted ethylene is recycled after product recovery.
What determines the product distribution in multiple reactions?
Answer: (D) Relative rates, set by concentrations, temperature and reactor type
Reactor choice and conditions are tools for selectivity.
What is a mixed series–parallel reaction?
Answer: (A) A system in which a reactant takes part in both series and parallel steps, such as A + B → R and R + B → S
Contacting pattern of B affects selectivity.
For A + B → R (desired) and R + B → S, how should B be added to maximise R?
Answer: (C) Gradually, keeping B concentration low relative to A
Semi-batch addition helps.
For parallel reactions with equal orders, what affects the selectivity?
Answer: (D) Only the ratio of rate constants, mainly through temperature and catalyst choice
Concentration effects cancel.
What is the effect of back-mixing on the yield of an intermediate in series reactions?
Answer: (B) It lowers the yield
Back-mixing mixes reacted and fresh material.
What is the maximum concentration ratio CR,max/CA0 for A → R → S in a PFR when k₁ = k₂?
Answer: (D) 1/e, about 0.368
For equal rate constants CRmax/CA0 = 1/e.
What is the instantaneous selectivity of R over S for A → R (rate k₁CA) and A → S (rate k₂CA²)?
Answer: (D) k₁/(k₂CA)
Low CA favours R, so a CSTR is preferred.
For A → R (rate k₁CA²) and A → S (rate k₂CA), which conditions favour R?
Answer: (B) High concentration of A, as in a PFR or batch reactor without dilution
The desired reaction has higher order.
In series reaction A → R → S, what is CR at any time in a batch reactor with k₁ ≠ k₂?
Answer: (A) CA0 k₁/(k₂ − k₁)[exp(−k₁t) − exp(−k₂t)]
This is the classical consecutive-reaction solution.
For A → R → S in a batch reactor with k₁ = 0.2 and k₂ = 0.1 min⁻¹, when is CR maximum?
Answer: (C) About 6.93 min
tmax = ln(k₂/k₁)/(k₂ − k₁) = ln 0.5/(−0.1).
What is the optimum space time for maximum R in a CSTR for A → R → S with first-order steps?
Answer: (A) τ = 1/√(k₁k₂)
It differs from the PFR optimum.
What is the yield of R for parallel first-order reactions A → R (k₁) and A → S (k₂)?
Answer: (B) k₁/(k₁ + k₂), independent of conversion
Both paths have the same order.
What is the yield of R from parallel first-order reactions with k₁ = 3 and k₂ = 1 (same units)?
Answer: (D) 75%
3/(3 + 1).
Why is a high temperature preferred in parallel reactions where the side reaction has the lower activation energy?
Answer: (B) The desired reaction's rate rises faster with temperature
Compare activation energies to choose temperature.
What is an example of reactions in series where over-reaction must be limited?
Answer: (A) Chlorination of methane giving CH₃Cl, CH₂Cl₂, CHCl₃ and CCl₄ successively
Excess methane favours monochlorination.
What is the purpose of recycling unreacted feed in multiple-reaction systems?
Answer: (D) To allow low conversion per pass for better selectivity while achieving high overall conversion
Separation costs must be balanced.
What does the term yield usually express in an industrial reactor?
Answer: (A) Moles of desired product formed per mole of key reactant fed (or consumed)
Yield = selectivity × conversion when based on feed.
What is the overall yield if conversion is 80% and selectivity (fraction of converted reactant going to product) is 90%?
Answer: (A) 72%
0.8 × 0.9.
For the parallel reactions A + B → R (desired, rate k₁CACB²) and A + B → S (rate k₂CA²CB), what contacting pattern favours R?
Answer: (D) High concentration of B and low concentration of A, for example adding A slowly to B
Compare the concentration exponents of each reactant.
What does the term differential selectivity mean?
Answer: (C) The local ratio of rates of formation of desired to undesired products
Integrating over the reactor gives overall selectivity.