What is the design equation for an ideal batch reactor?
Show answer & solution
Answer: (D) t = NA0 ∫ dXA/((−rA)V)
For constant volume, t = CA0 ∫ dXA/(−rA).
Chemical Engineering · Chemical Reaction Engineering
38 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the design equation for an ideal batch reactor?
Answer: (D) t = NA0 ∫ dXA/((−rA)V)
For constant volume, t = CA0 ∫ dXA/(−rA).
What is the design equation for an ideal CSTR (mixed flow reactor)?
Answer: (A) V/FA0 = XA/(−rA), with rate evaluated at exit conditions
The whole reactor operates at outlet concentration.
What is the design equation for an ideal plug flow reactor (PFR)?
Answer: (C) V/FA0 = ∫ dXA/(−rA) from 0 to XA
Concentration varies along the length.
What is space time τ?
Answer: (D) The reactor volume divided by the volumetric feed rate at inlet conditions
τ = V/v₀.
What is space velocity?
Answer: (C) The reciprocal of space time
Units are reciprocal time, such as h⁻¹.
What is the space time of a 10 m³ reactor receiving 2 m³/min of feed?
Answer: (B) 5 min
τ = 10/2.
For a first-order reaction in a CSTR, what is the conversion in terms of Damköhler number Da = kτ?
Answer: (D) XA = kτ/(1 + kτ)
For a PFR it is 1 − exp(−kτ).
What is the conversion in a CSTR for a first-order reaction with kτ = 4?
Answer: (C) 80%
4/(1 + 4).
What is the conversion in a PFR for a first-order reaction with kτ = 2.303?
Answer: (C) 90%
1 − exp(−2.303) = 0.90.
Which reactor needs the smaller volume for a given conversion with positive-order kinetics?
Answer: (A) PFR
The CSTR operates at the lowest concentration throughout.
For which reaction order do CSTR and PFR require the same volume for any conversion?
Answer: (A) Zero order
Rate does not depend on concentration.
How do N equal-size CSTRs in series compare with a single PFR as N becomes very large?
Answer: (D) Their performance approaches that of a PFR
Each tank is a small step on the 1/(−rA) curve.
What is the conversion after two equal CSTRs in series for a first-order reaction with kτ = 1 in each?
Answer: (C) 75%
CA/CA0 = 1/(1 + 1)² = 0.25.
What does a Levenspiel plot show?
Answer: (B) 1/(−rA) against conversion, used to compare reactor volumes graphically
PFR volume is the area under the curve, CSTR volume a rectangle.
Which reactor is best for an autocatalytic reaction at low conversion?
Answer: (D) CSTR
The CSTR operates near the maximum rate; a CSTR followed by a PFR is often optimal.
What is a recycle reactor?
Answer: (A) A PFR in which part of the product is returned to the inlet
At infinite recycle it behaves like a CSTR.
What is the residence time in an ideal CSTR equal to for constant density?
Answer: (B) The space time V/v₀ on average
Individual elements have an exponential residence time distribution.
What is the Damköhler number?
Answer: (A) The ratio of reaction rate to convective transport rate, kτCA0^(n−1)
High Da means high conversion.
What is a semi-batch reactor?
Answer: (D) A reactor in which one reactant is charged initially and another is fed gradually
It helps control heat release and selectivity.
What is the design equation for a packed bed catalytic reactor?
Answer: (B) W/FA0 = ∫ dXA/(−r′A), with rate per unit mass of catalyst
W is the catalyst weight.
What is thermal runaway in an exothermic reactor?
Answer: (B) An uncontrolled rise in temperature when heat generation exceeds heat removal
It can lead to explosions and is a major safety concern.
Why can an exothermic CSTR have multiple steady states?
Answer: (C) The S-shaped heat generation curve can cross the straight heat removal line at more than one point
The middle steady state is unstable.
What is the adiabatic temperature rise for complete conversion in a reactor?
Answer: (D) The temperature rise when all heat of reaction raises the temperature of the reacting mixture with no heat loss
ΔTad = (−ΔH)CA0/(ρCp).
For a reversible exothermic reaction, how should temperature be varied along a PFR for maximum rate?
Answer: (A) Start high and decrease along the reactor
High temperature gives speed early; lower temperature favours equilibrium later.
For an endothermic reaction, which temperature policy is favourable?
Answer: (C) The highest allowable temperature
Both rate and equilibrium improve with temperature.
What is the mean residence time in a PFR?
Answer: (B) Equal to the space time for constant density, with every element staying the same time
PFR has no axial mixing.
What is the volume of a CSTR needed for 50% conversion of a first-order reaction with k = 0.2 min⁻¹ and feed of 1 m³/min?
Answer: (C) 5 m³
τ = X/(k(1 − X)) = 0.5/(0.2 × 0.5) = 5 min.
What is the volume of a PFR for the same duty (50% conversion, k = 0.2 min⁻¹, 1 m³/min)?
Answer: (B) About 3.47 m³
τ = ln 2/0.2 = 3.47 min.
What is the overall conversion if a feed passes through two reactors giving X₁ = 0.5 and then converts half of what remains?
Answer: (C) 75%
1 − 0.5 × 0.5.
What is the energy balance for an adiabatic PFR or batch reactor with constant properties?
Answer: (C) Temperature rises linearly with conversion: T = T₀ + ΔTad × X
This holds when Cp is constant.
What is the adiabatic temperature rise when CA0 = 2 kmol/m³, −ΔH = 50,000 kJ/kmol and ρCp = 4,000 kJ/(m³·K)?
Answer: (B) 25 K
ΔTad = 2 × 50,000/4,000.
What is the volume of a batch reactor needed per day if each batch takes 4 h total and 24 m³ of product is needed daily?
Answer: (A) 4 m³
Six batches per day of 4 m³ each.
How does conversion change with increasing space time in a CSTR for a first-order reaction?
Answer: (C) It increases, approaching 100% asymptotically
X = kτ/(1 + kτ).
What is the main advantage of a CSTR for highly exothermic liquid reactions?
Answer: (D) Uniform temperature and easy temperature control
Feed is diluted immediately into the mixture.
What is the main advantage of a PFR?
Answer: (B) High conversion per unit volume for positive-order reactions
Tubular reactors are used for gas-phase reactions.
Why are batch reactors preferred in the pharmaceutical and fine chemical industries?
Answer: (C) They are flexible for small-volume, multi-product operation
Batch traceability is also important.
What is the effect of feeding a gas-phase reaction A → 2R with inerts on volume change?
Answer: (D) It reduces the expansion factor
Inerts dilute the fractional volume change.
What is the mean residence time of gas in a reactor if volume change occurs on reaction?
Answer: (B) It differs from space time and must be found by integrating along the reactor
For liquids with constant density they are equal.