What is a catalyst?
Show answer & solution
Answer: (B) A substance that increases the rate of a reaction without being consumed overall
It does not change equilibrium.
Chemical Engineering · Chemical Reaction Engineering
38 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is a catalyst?
Answer: (B) A substance that increases the rate of a reaction without being consumed overall
It does not change equilibrium.
What is heterogeneous catalysis?
Answer: (A) Catalysis in which the catalyst is in a different phase from the reactants, usually a solid with gas or liquid
Ammonia synthesis on iron is an example.
What are the sequential steps in a heterogeneous catalytic reaction?
Answer: (C) External diffusion, pore diffusion, adsorption, surface reaction, desorption and diffusion of products out
The slowest step controls the rate.
What is the Langmuir–Hinshelwood mechanism?
Answer: (D) A surface reaction between two adsorbed species on adjacent sites
It gives rate laws with squared denominators.
What is the Eley–Rideal mechanism?
Answer: (B) Reaction between an adsorbed species and a gas-phase molecule
It differs from Langmuir–Hinshelwood in that only one reactant is adsorbed.
What is the effectiveness factor of a catalyst pellet?
Answer: (D) The ratio of actual reaction rate in the pellet to the rate if the whole interior were at surface conditions
It is less than 1 when pore diffusion limits the rate.
What is the Thiele modulus?
Answer: (A) A dimensionless number comparing surface reaction rate to pore diffusion rate
Large values mean strong diffusion limitation.
What is the effectiveness factor when the Thiele modulus is very large?
Answer: (B) Approximately 1/Thiele modulus, much less than 1
Reaction occurs only near the pellet surface.
How can pore diffusion limitations be reduced?
Answer: (C) By using smaller catalyst particles or larger pores
Smaller particles increase pressure drop.
What is the apparent activation energy under strong pore diffusion control?
Answer: (A) About half the true activation energy
This helps diagnose diffusion limits.
How can external mass transfer limitations be detected experimentally?
Answer: (B) Rate changes when flow velocity changes at constant space time
If rate is independent of velocity, external transfer is not limiting.
What is catalyst deactivation?
Answer: (D) Loss of catalyst activity with time by poisoning, fouling or sintering
Deactivation is common in refinery catalysts.
What is catalyst poisoning?
Answer: (C) Strong chemisorption of impurities on active sites, blocking them
Sulphur poisons nickel and platinum catalysts.
What is coking (fouling) of catalyst?
Answer: (C) Deposition of carbonaceous material on the surface and in pores
FCC catalysts are regenerated by burning off coke.
What is sintering of a catalyst?
Answer: (D) Loss of active surface area due to growth of metal crystallites at high temperature
It is usually irreversible.
What is a catalyst promoter?
Answer: (A) A substance that improves the activity, selectivity or stability of a catalyst though not active itself
K₂O and Al₂O₃ promote iron in ammonia synthesis.
What is the role of a catalyst support?
Answer: (B) To provide a high surface area and mechanical strength for dispersing the active material
Alumina, silica and zeolites are common supports.
Which catalyst is used for ammonia synthesis?
Answer: (C) Promoted iron
Haber–Bosch converters in Pakistani fertiliser plants use promoted iron.
Which catalyst is used for oxidation of SO₂ to SO₃ in the contact process?
Answer: (D) Vanadium pentoxide
Caesium promoters lower the operating temperature.
Which catalyst is used in steam reforming of natural gas?
Answer: (B) Nickel on alumina
Reforming occurs in tubes inside a fired furnace.
Which catalyst is used for ammonia oxidation to nitric oxide in nitric acid production?
Answer: (A) Platinum–rhodium gauze
Contact time is extremely short.
What is the main catalyst in fluid catalytic cracking (FCC)?
Answer: (D) Zeolite Y in a silica–alumina matrix
FCC converts heavy gas oil to gasoline.
What is the turnover frequency of a catalyst?
Answer: (C) The number of molecules reacting per active site per unit time
It compares intrinsic activity.
What is the purpose of catalyst regeneration?
Answer: (A) Restoring activity, for example by burning off coke
Continuous catalytic regeneration is used in reformers.
What type of reactor is used for highly exothermic catalytic reactions needing good temperature control?
Answer: (B) Fluidised bed or multitubular fixed bed with coolant
Phthalic anhydride and FCC use such designs.
What is a trickle bed reactor?
Answer: (A) A fixed bed of catalyst with liquid flowing down and gas flowing co-currently
Hydrotreating in refineries uses trickle beds.
What is a slurry reactor?
Answer: (C) A reactor with fine catalyst particles suspended in liquid through which gas is bubbled
Hydrogenation of edible oils uses nickel catalysts in slurry reactors.
What is the shrinking core model used for?
Answer: (B) Gas–solid non-catalytic reactions in which an unreacted core shrinks as reaction proceeds
Roasting of ores and coal combustion are examples.
Which steps may control the rate in the shrinking core model?
Answer: (D) Gas film diffusion, ash layer diffusion or chemical reaction
Each gives a different time–conversion relation.
What is the effect of a catalyst on the heat of reaction?
Answer: (B) No effect
Heat of reaction depends only on initial and final states.
What is a bioreactor (fermenter) used for in Pakistani industry?
Answer: (A) Producing ethanol from molasses using yeast
Fermenters are also used for antibiotics and vinegar.
What is the Monod equation?
Answer: (C) μ = μmax S/(Ks + S), describing microbial growth rate as a function of substrate
It is similar in form to Michaelis–Menten kinetics.
What is the purpose of a guard bed upstream of a catalytic reactor?
Answer: (C) To remove poisons such as sulphur before they reach the main catalyst
Zinc oxide beds remove H₂S before reformers.
What is the catalyst used in the low-temperature shift converter of ammonia plants?
Answer: (B) Copper–zinc oxide on alumina
High-temperature shift uses iron–chromium oxide.
What is the catalyst used in hydrodesulphurisation (HDS) in refineries?
Answer: (A) Cobalt–molybdenum or nickel–molybdenum sulphides on alumina
HDS removes sulphur from naphtha and diesel.
What is the catalyst used in catalytic reforming of naphtha?
Answer: (A) Platinum (often with rhenium or tin) on chlorided alumina
Reforming raises octane number by forming aromatics.
What is selectivity of a catalyst?
Answer: (B) Its ability to direct the reaction toward a desired product among possible products
Zeolite shape selectivity is an example.
Why are pellets of catalyst made porous?
Answer: (A) To provide a large internal surface area for reaction
Typical surface areas are 100–300 m²/g.