What is a well constructed by drilling a borehole and installing pipes with a strainer and pump called?
Show answer & solution
Answer: (C) Tubewell
Tubewells tap water from deep aquifers.
Agriculture · Agricultural Engineering
34 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is a well constructed by drilling a borehole and installing pipes with a strainer and pump called?
Answer: (C) Tubewell
Tubewells tap water from deep aquifers.
Which part of a tubewell allows water to enter from the aquifer while keeping sand out?
Answer: (C) Strainer (well screen)
Strainer slots are sized to match the aquifer material.
What is the plain, unperforated pipe in a tubewell placed against non-water-bearing layers called?
Answer: (C) Blind pipe (housing pipe)
The pump is usually installed inside the housing pipe.
What is the layer of graded gravel placed around the strainer of a tubewell called?
Answer: (D) Gravel pack (shrouding)
It keeps fine sand out and increases the well's yield.
What is removing fine particles from around a new tubewell by surging or over-pumping called?
Answer: (C) Well development
Development increases yield and reduces sand pumping.
Which drilling method, using a heavy bit lifted and dropped repeatedly, is used for tubewells?
Answer: (A) Percussion (cable tool) drilling
It is slow but suits many formations.
Which drilling method, which removes cuttings through the drill pipe by suction, is widely used for large tubewells in alluvial soils?
Answer: (B) Reverse circulation rotary drilling
It is fast in unconsolidated sand and gravel.
Which material is added to drilling fluid to support borehole walls during rotary drilling?
Answer: (B) Bentonite clay
The drilling mud is removed during well development.
Which material is now commonly used for tubewell strainers because it does not corrode?
Answer: (D) PVC or fibreglass
Mild steel strainers corrode in brackish water.
What is a shallow well dug by hand and usually lined with bricks called?
Answer: (A) Dug (open) well
Persian wheels were used to lift water from dug wells.
Which type of pump moves water by a rotating impeller inside a casing?
Answer: (D) Centrifugal pump
The spiral casing around the impeller is called the volute.
Which valve at the bottom of the suction pipe of a centrifugal pump keeps the pump filled with water?
Answer: (B) Foot valve
It usually has a strainer to stop debris.
What type of pump moves water using a piston moving back and forth in a cylinder?
Answer: (D) Reciprocating (positive displacement) pump
Hand pumps are reciprocating pumps.
What is the main feature of a submersible pump?
Answer: (A) The pump and motor work together under water inside the well
Submersible pumps suit deep, narrow wells.
What is the total head that a pump must work against?
Answer: (D) Suction head plus delivery head plus friction losses
Total head determines the power required.
What is the maximum theoretical suction lift of water at sea level?
Answer: (B) About 10.3 m
In practice, surface centrifugal pumps lift only about 6–7 m by suction.
What is the water horsepower of a pump delivering 30 litres per second against a total head of 10 m?
Answer: (A) 4 hp
Water horsepower (metric) = Q (L/s) × H (m) / 75.
If a pump needs 4 water hp and its efficiency is 50%, what brake horsepower must the engine supply?
Answer: (A) 8 hp
Brake hp = water hp / pump efficiency.
What is the ratio of water horsepower to brake horsepower called?
Answer: (A) Pump efficiency
Worn impellers and poor matching reduce pump efficiency.
How does the discharge of a centrifugal pump change when its speed is doubled?
Answer: (B) It doubles
Under the affinity laws, head rises with the square and power with the cube of speed.
What happens when two identical pumps are connected in parallel?
Answer: (D) Discharge increases at the same head
Pumps in series increase the head.
Which type of electric motor is most commonly used to run tubewells?
Answer: (B) Three-phase induction motor
Induction motors are simple, rugged and efficient.
What does a solar water pumping system use to convert sunlight into electricity?
Answer: (A) Photovoltaic (PV) panels
A controller or inverter runs the pump motor from the panels.
In what unit is the output rating of a solar panel expressed?
Answer: (A) Peak watts (Wp)
Panel output depends on sunlight intensity and angle.
Why must solar panels be cleaned regularly in dusty areas?
Answer: (C) Dust reduces the sunlight reaching cells and lowers output
Facing panels south at a suitable tilt also improves output in Pakistan.
Which device uses the energy of flowing water to pump a part of it to a higher level without fuel or electricity?
Answer: (B) Hydraulic ram
It is useful in hilly streams.
What is the main gas in biogas produced from animal dung?
Answer: (C) Methane
Biogas contains about 55–65% methane.
Which two common designs of biogas plant are used on farms?
Answer: (A) Fixed dome and floating drum
The digested slurry is a good organic manure.
What is the by-product of a biogas plant that is used as manure?
Answer: (B) Digested slurry
It is richer in available nutrients than raw dung.
Which renewable device has long been used to pump water using wind energy?
Answer: (C) Windmill
Windmills suit areas with steady winds such as coastal Sindh and Balochistan.
Why should the tubewell pump be matched to the well's yield?
Answer: (D) Over-sized pumps cause excess drawdown, sand pumping and inefficiency
A pump test determines the safe yield of a well.
What is the main purpose of a pumping test on a new tubewell?
Answer: (A) To determine its discharge, drawdown and safe yield
Results guide pump selection.
Which routine maintenance keeps a diesel tubewell engine efficient?
Answer: (C) Regular oil change, air and fuel filter cleaning and correct belt tension
Good maintenance saves fuel and extends engine life.
Why are flat belts and V-belts used in many farm machines such as threshers and tubewells?
Answer: (D) To transmit power from the engine to the machine
V-belts grip better and slip less than flat belts.