Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Renewable Energy: Wind Energy

Electrical Engineering · Renewable Energy

26 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the formula for the power available in the wind passing through a turbine's swept area?

  1. P = ½ρAv³
  2. P = ρAv
  3. P = ρv³/A
  4. P = ½ρAv²
Show answer & solution

Answer: (A) P = ½ρAv³

ρ is air density, A swept area and v wind speed.

Question 2

By what factor does available wind power increase if wind speed doubles?

  1. 2 times
  2. 4 times
  3. 8 times
  4. 16 times
Show answer & solution

Answer: (C) 8 times

Power is proportional to the cube of wind speed.

Question 3

What is the wind power available through a swept area of 100 m² at 10 m/s with air density 1.225 kg/m³?

  1. About 6.1 kW
  2. About 12 kW
  3. About 61 kW
  4. About 612 kW
Show answer & solution

Answer: (C) About 61 kW

P = 0.5 × 1.225 × 100 × 10³ ≈ 61,250 W.

Question 4

What is the Betz limit?

  1. The rated power of a turbine
  2. The maximum theoretical fraction of wind power that a turbine can extract, about 59.3%
  3. The minimum blade length
  4. The maximum wind speed
Show answer & solution

Answer: (B) The maximum theoretical fraction of wind power that a turbine can extract, about 59.3%

Practical turbines achieve power coefficients of about 0.4–0.5.

Question 5

What is the swept area of a turbine with a rotor radius of 40 m?

  1. About 251 m²
  2. About 1,600 m²
  3. About 5,027 m²
  4. About 50,270 m²
Show answer & solution

Answer: (C) About 5,027 m²

A = πR² = π × 1,600.

Question 6

What is the tip speed ratio of a wind turbine?

  1. The ratio of power to wind speed
  2. The ratio of blade tip speed to wind speed
  3. The ratio of tower height to blade length
  4. The ratio of rotor speed to generator speed
Show answer & solution

Answer: (B) The ratio of blade tip speed to wind speed

Optimum values for three-bladed turbines are about 6–8.

Question 7

Which type of wind turbine is most common in large wind farms?

  1. Three-bladed horizontal-axis wind turbine
  2. Savonius vertical-axis turbine
  3. Darrieus turbine
  4. Multi-blade water-pumping windmill
Show answer & solution

Answer: (A) Three-bladed horizontal-axis wind turbine

HAWTs have the highest efficiency.

Question 8

What is a Savonius rotor?

  1. A hydro turbine
  2. A lift-type horizontal turbine
  3. A three-bladed HAWT
  4. A drag-type vertical-axis wind turbine with curved scoops
Show answer & solution

Answer: (D) A drag-type vertical-axis wind turbine with curved scoops

It has high starting torque but low efficiency.

Question 9

What is the cut-in wind speed of a turbine?

  1. The rated speed
  2. The minimum wind speed at which it starts generating power
  3. The average wind speed
  4. The speed at which it shuts down
Show answer & solution

Answer: (B) The minimum wind speed at which it starts generating power

Typical cut-in speeds are about 3–4 m/s.

Question 10

Why does a wind turbine shut down at its cut-out speed?

  1. To protect it from damage in very high winds
  2. Because the grid fails
  3. Because power becomes zero
  4. To save energy
Show answer & solution

Answer: (A) To protect it from damage in very high winds

Typical cut-out speeds are about 25 m/s.

Question 11

What is the purpose of blade pitch control in large wind turbines?

  1. To change the direction the nacelle faces
  2. To brake the tower
  3. To measure wind speed
  4. To regulate power and limit loads by changing blade angle
Show answer & solution

Answer: (D) To regulate power and limit loads by changing blade angle

Pitch control keeps output near rated power above rated wind speed.

Question 12

What is the purpose of the yaw system in a wind turbine?

  1. To turn the nacelle and rotor to face the wind
  2. To cool the gearbox
  3. To control generator voltage
  4. To change blade pitch
Show answer & solution

Answer: (A) To turn the nacelle and rotor to face the wind

A wind vane provides direction input.

Question 13

What is a doubly fed induction generator (DFIG) in wind turbines?

  1. A diesel generator
  2. A synchronous generator with no converter
  3. A permanent magnet DC generator
  4. A wound-rotor induction generator whose rotor is fed by a partially rated converter for variable-speed operation
Show answer & solution

Answer: (D) A wound-rotor induction generator whose rotor is fed by a partially rated converter for variable-speed operation

The converter handles only about 30% of rated power.

Question 14

What is the main advantage of permanent-magnet synchronous generators with full converters in wind turbines?

  1. Fixed speed only
  2. No converter needed
  3. Wide variable-speed operation and the option of gearless direct-drive designs
  4. Lower efficiency
Show answer & solution

Answer: (C) Wide variable-speed operation and the option of gearless direct-drive designs

Direct-drive removes gearbox maintenance.

Question 15

How does wind speed generally change with height above the ground?

  1. It becomes zero at high altitude
  2. It decreases with height
  3. It stays constant
  4. It increases with height
Show answer & solution

Answer: (D) It increases with height

This is why turbines are mounted on tall towers.

Question 16

What is the typical capacity factor of wind farms in good sites such as the Gharo–Jhimpir corridor?

  1. About 5%
  2. About 30 to 40%
  3. About 90%
  4. About 100%
Show answer & solution

Answer: (B) About 30 to 40%

Strong, steady monsoon winds give good capacity factors.

Question 17

Where is Pakistan's main wind energy corridor located?

  1. Gharo–Jhimpir in Sindh
  2. Quetta valley
  3. Thar desert in Punjab
  4. Swat valley
Show answer & solution

Answer: (A) Gharo–Jhimpir in Sindh

Many wind farms operate near Thatta and Jhimpir.

Question 18

What is the wake effect in wind farms?

  1. Reduced wind speed and increased turbulence behind turbines that lower output of downstream turbines
  2. A lightning effect
  3. A grid fault
  4. An increase in wind speed
Show answer & solution

Answer: (A) Reduced wind speed and increased turbulence behind turbines that lower output of downstream turbines

Turbines are spaced several rotor diameters apart.

Question 19

Why is the gearbox used in many wind turbines?

  1. To turn the nacelle
  2. To change blade pitch
  3. To decrease generator speed
  4. To increase the slow rotor speed to the higher speed needed by the generator
Show answer & solution

Answer: (D) To increase the slow rotor speed to the higher speed needed by the generator

Gearboxes are a common source of maintenance in turbines.

Question 20

What is the power coefficient Cp of a wind turbine?

  1. The generator efficiency only
  2. The power at rated speed
  3. The fraction of wind power actually converted into mechanical power
  4. The tower height ratio
Show answer & solution

Answer: (C) The fraction of wind power actually converted into mechanical power

Cp cannot exceed the Betz limit.

Question 21

What happens to the power of a wind turbine if the rotor diameter is doubled at the same wind speed?

  1. It doubles
  2. It becomes four times
  3. It becomes eight times
  4. It stays the same
Show answer & solution

Answer: (B) It becomes four times

Swept area is proportional to the square of diameter.

Question 22

What is offshore wind energy?

  1. Wind power in mountains
  2. Solar power at sea
  3. Wind power from turbines installed in sea or lake waters
  4. Tidal power
Show answer & solution

Answer: (C) Wind power from turbines installed in sea or lake waters

Offshore winds are stronger and steadier.

Question 23

What is low-voltage ride-through (LVRT) capability of wind turbines?

  1. Operating at low wind only
  2. Operating without a grid
  3. Shutting down at every dip
  4. The ability to stay connected during short voltage dips caused by grid faults
Show answer & solution

Answer: (D) The ability to stay connected during short voltage dips caused by grid faults

Grid codes require LVRT to support system stability.

Question 24

Which type of vertical-axis wind turbine uses curved aerofoil blades that produce lift?

  1. Savonius turbine
  2. Darrieus turbine
  3. Pelton turbine
  4. Kaplan turbine
Show answer & solution

Answer: (B) Darrieus turbine

It may need help to start.

Question 25

What is the rated wind speed of a turbine?

  1. The wind speed at which it first reaches its rated power output
  2. The average annual wind speed
  3. The cut-out speed
  4. The cut-in speed
Show answer & solution

Answer: (A) The wind speed at which it first reaches its rated power output

It is typically about 11–13 m/s.

Question 26

What is the main purpose of a wind resource assessment before building a wind farm?

  1. To set tariffs
  2. To test soil only
  3. To measure solar radiation
  4. To measure wind speed and direction over time to estimate energy production
Show answer & solution

Answer: (D) To measure wind speed and direction over time to estimate energy production

Met masts or lidar are used for at least a year.

Practice these 26 questions interactively →