Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Public Health Engineering: Water Supply, Quality and Distribution

Civil Engineering · Public Health Engineering

36 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

An intake structure on a surface source is designed with attention to

  1. water level variation, exclusion of debris and silt, and reliable supply
  2. a fixed intake level set at the average river stage, with no allowance for flood or drought
  3. location on the inside of a river bend, where velocity is lowest and silt deposition is greatest
  4. a single standard design that suits all rivers, lakes and canals without site adjustment
Show answer & solution

Answer: (A) water level variation, exclusion of debris and silt, and reliable supply

Intakes must work at low and flood levels and exclude debris and silt.

Question 2

Total Dissolved Solids (TDS) in water refers to

  1. total bacterial count of the water sample
  2. suspended particles retained on a filter paper
  3. dissolved mineral and organic substances in the water
  4. dissolved oxygen concentration of the water sample
Show answer & solution

Answer: (C) dissolved mineral and organic substances in the water

TDS is the amount of dissolved matter, mainly mineral salts, usually expressed in mg/L.

Question 3

The commonly used layout patterns for water distribution networks are

  1. dead-end (tree), grid-iron, circular (ring) and radial systems
  2. combined, separate, partially separate and storm systems
  3. gravity, vacuum, pneumatic and siphon systems
  4. dead-end, activated sludge, ring and trickling filter systems, in order of increasing cost
Show answer & solution

Answer: (A) dead-end (tree), grid-iron, circular (ring) and radial systems

Standard classification: dead-end, grid-iron, ring (circular) and radial layouts.

Question 4

A typical house service connection consists of

  1. a manhole, an inspection chamber and a trap
  2. a service pipe tapped to the main, a stop-cock, and a water meter where metered
  3. a settling tank, a filter bed and a chlorinator fitted at each consumer's premises
  4. a grit chamber, a screen and a flow meter
Show answer & solution

Answer: (B) a service pipe tapped to the main, a stop-cock, and a water meter where metered

Service connection: ferrule/tapping, service pipe (goose neck), stop-cock and meter.

Question 5

Dissolved oxygen in a natural water body is important mainly because

  1. it controls the taste and odour of the water, and a high DO signals heavy organic pollution
  2. it makes the water hard and scale forming by precipitating calcium carbonate
  3. most aquatic life needs it and low DO signals organic pollution
  4. it is needed only by bacteria, and falling DO shows that the water is becoming cleaner
Show answer & solution

Answer: (C) most aquatic life needs it and low DO signals organic pollution

Fish require DO of about 4–5 mg/L or more; organic pollution depletes DO.

Question 6

Air valves are provided at high points of a pipeline mainly to

  1. reduce pressure when it exceeds the working limit
  2. drain the sediment that accumulates at the bottom of the pipe at the high point
  3. dose chlorine into the flowing water
  4. release accumulated air and admit air during draining to avoid vacuum
Show answer & solution

Answer: (D) release accumulated air and admit air during draining to avoid vacuum

Trapped air restricts flow; air valves expel it, and admit air when the line empties to avoid collapse.

Question 7

Fluoride in drinking water is of concern mainly because

  1. it causes methaemoglobinaemia in infants when present above 1.5 mg/L in the water
  2. excess intake causes goitre, while a small amount in water protects the thyroid
  3. a little protects teeth but excess causes dental and skeletal fluorosis
  4. it causes cholera and typhoid when present above 0.1 mg/L in the water supply
Show answer & solution

Answer: (C) a little protects teeth but excess causes dental and skeletal fluorosis

WHO guideline value for fluoride is 1.5 mg/L; higher levels cause fluorosis.

Question 8

Public water supply sources are broadly classified into which two categories?

  1. Surface sources and groundwater sources
  2. Gravity sources and pumped sources only
  3. Perennial sources and seasonal sources only
  4. Natural sources and artificial sources only
Show answer & solution

Answer: (A) Surface sources and groundwater sources

Water sources are classed as surface (rivers, lakes, reservoirs) and subsurface/groundwater (wells, springs).

Question 9

Distribution (service) reservoirs are provided mainly to

  1. remove turbidity and bacteria from the water by plain sedimentation before it is supplied
  2. provide long-term storage of raw water for treatment during drought and seasonal low flows
  3. reduce friction losses in the trunk main by increasing the diameter of the pipes leaving the plant
  4. balance fluctuating demand against steady supply and hold fire-fighting and emergency reserve
Show answer & solution

Answer: (D) balance fluctuating demand against steady supply and hold fire-fighting and emergency reserve

Balancing (equalizing) storage, emergency and fire reserve are the functions of a service reservoir.

Question 10

Water meters at consumer connections serve mainly to

  1. measure the volume consumed, enabling volumetric billing and encouraging conservation
  2. regulate and reduce the pressure inside the house plumbing, protecting the fixtures from damage
  3. remove impurities such as sediment and rust from the water before it enters the house pipes
  4. disinfect water at the point of delivery by dosing a small amount of chlorine into the flow
Show answer & solution

Answer: (A) measure the volume consumed, enabling volumetric billing and encouraging conservation

Metering permits billing by consumption and reduces wastage; flat-rate billing gives no such incentive.

Question 11

Hardness of water, caused by calcium and magnesium salts, is undesirable mainly because it

  1. improves the lathering of soap and reduces its use
  2. gives water a pink colour and a sour taste
  3. raises soap consumption and forms scale in pipes and boilers
  4. causes acute poisoning at all concentrations in drinking water
Show answer & solution

Answer: (C) raises soap consumption and forms scale in pipes and boilers

Hardness causes soap waste and scale deposits; it is mainly a domestic and industrial nuisance.

Question 12

Drinking water quality standards (such as WHO guidelines and national standards) specify permissible limits mainly to

  1. set a single limit that applies equally to drinking and industrial water
  2. recover the cost of water treatment from the consumers of the supply
  3. ensure that supplied water is safe for consumption
  4. limit the quantity of water abstracted from the source in dry seasons
Show answer & solution

Answer: (C) ensure that supplied water is safe for consumption

Standards define safe limits for physical, chemical and microbiological parameters to protect public health.

Question 13

The pH of water is important mainly because

  1. it indicates the dissolved oxygen and organic load of the water
  2. it affects corrosion, coagulation and disinfection efficiency
  3. it measures the total hardness and alkalinity of the water
  4. it measures the turbidity and colour of the water supply
Show answer & solution

Answer: (B) it affects corrosion, coagulation and disinfection efficiency

Low pH causes corrosion; pH also controls coagulation and chlorine efficacy (WHO suggests about 6.5–8.5 for drinking water).

Question 14

Adequate residual pressure in a distribution network is important because low pressure

  1. causes excessive leakage and bursts in the mains, although supply at the taps is unaffected
  2. affects only the fire-fighting flow, while domestic supply at upper floors stays adequate
  3. increases the velocity in the mains and so keeps the pipes free of sediment deposits
  4. reduces supply at the taps and can let contaminated external water be drawn into leaking pipes
Show answer & solution

Answer: (D) reduces supply at the taps and can let contaminated external water be drawn into leaking pipes

Negative or very low pressure causes poor supply and back-siphonage/infiltration through leaks; a minimum residual head (commonly about 7-15 m) is adopted in design.

Question 15

The presence of coliform bacteria in a water sample indicates

  1. excessive hardness caused by dissolved calcium and magnesium salts
  2. high turbidity caused by suspended clay and silt particles
  3. possible faecal contamination and potential pathogens
  4. dissolved iron and manganese causing colour and taste problems
Show answer & solution

Answer: (C) possible faecal contamination and potential pathogens

Coliforms, especially E. coli, are indicators of faecal pollution.

Question 16

Water hammer in a pipeline is caused mainly by

  1. gradual growth of biofilm in the pipe
  2. chemical corrosion of the pipe wall
  3. very slow closing of a valve over several hours, which converts kinetic energy into pressure
  4. a sudden change in flow velocity, such as rapid valve closure or a pump trip
Show answer & solution

Answer: (D) a sudden change in flow velocity, such as rapid valve closure or a pump trip

Rapid velocity change converts kinetic energy to pressure waves; surge ΔP = ρ·c·ΔV (Joukowsky).

Question 17

Non-revenue water (NRW) is best defined as

  1. water produced by the utility but lost through leakage or unbilled use, earning no revenue
  2. water lost in the catchment before it reaches the intake
  3. water used by the utility for treatment plant operations only
  4. water sold to consumers and fully billed, which is the revenue-earning part of the production
Show answer & solution

Answer: (A) water produced by the utility but lost through leakage or unbilled use, earning no revenue

NRW = system input minus billed authorized consumption (physical losses, commercial losses, unbilled use).

Question 18

In Pakistani municipal water supply design practice, the per capita domestic water demand for urban areas is generally taken as about

  1. 30 to 50 litres per capita per day
  2. 50 to 70 litres per capita per day
  3. 135 to 200 litres per capita per day
  4. 250 to 300 litres per capita per day
Show answer & solution

Answer: (C) 135 to 200 litres per capita per day

Urban domestic demand in municipal (WASA-type) design is commonly assumed in the range of about 135–200 lpcd, depending on housing density and water availability.

Question 19

Pumping stations in a water supply system are used mainly to

  1. remove suspended solids and colour from the water before it enters the distribution system
  2. remove entrained air and dissolved gases from the water during its passage through the pumps
  3. store treated water to balance hourly variation in demand and hold a fire reserve
  4. supply the energy (head) needed to lift or convey water where gravity flow is insufficient
Show answer & solution

Answer: (D) supply the energy (head) needed to lift or convey water where gravity flow is insufficient

Pumps add head to overcome static lift, friction and pressure requirements.

Question 20

Scour (washout) valves are provided at low points of a pipeline mainly to

  1. measure the discharge flowing in the pipeline
  2. regulate pressure in the pipeline downstream
  3. release air that is trapped in the pipeline at its high points to avoid air locking
  4. drain the line and flush out accumulated silt and sediment
Show answer & solution

Answer: (D) drain the line and flush out accumulated silt and sediment

Scour valves at depressions allow emptying for repair and flushing out of deposited silt.

Question 21

Turbidity in drinking water is important mainly because it

  1. can shield pathogens from disinfection and looks objectionable
  2. increases chlorine action by providing surfaces on which pathogens are quickly killed
  3. mainly indicates dissolved gases and has no bearing on disinfection performance
  4. is caused only by dissolved salts and does not affect the acceptability of water
Show answer & solution

Answer: (A) can shield pathogens from disinfection and looks objectionable

Suspended particles protect microorganisms from chlorine and make water unattractive; WHO recommends turbidity below 5 NTU (ideally below 1 NTU for disinfection).

Question 22

Which of the following is a group of surface sources of water supply?

  1. Dug wells, springs and infiltration wells
  2. Rivers, lakes, ponds and impounding reservoirs
  3. Springs, infiltration galleries and tube wells
  4. Artesian wells, tube wells and springs
Show answer & solution

Answer: (B) Rivers, lakes, ponds and impounding reservoirs

Rivers, lakes, ponds and impounding reservoirs are surface water bodies; the others listed are subsurface sources.

Question 23

A dead-end (tree) distribution system is characterized by

  1. interconnected closed loops, so water reaches a point from several directions
  2. a ring main around the town with sub-mains fed from both sides so that supply continues during repairs
  3. parallel mains cross-connected at every street junction so that any section can be isolated without interruption
  4. branching mains with no closed loops, so water reaches any point from one direction only
Show answer & solution

Answer: (D) branching mains with no closed loops, so water reaches any point from one direction only

In a tree system a pipe break cuts off all downstream consumers and dead ends cause stagnation.

Question 24

Raw water from the source to the treatment plant is conveyed by

  1. open unlined earthen channels only, for all distances
  2. road tankers only, for all distances and heads
  3. gravity mains, pumping mains or a combination of both
  4. hand pumps and open wells located at the plant
Show answer & solution

Answer: (C) gravity mains, pumping mains or a combination of both

The choice depends on the relative elevations and the distance involved.

Question 25

The per capita water demand used in the design of a town water supply scheme normally includes allowance for which of the following?

  1. Domestic, industrial and commercial demands, with fire demand and losses excluded
  2. Domestic, industrial, commercial, public and fire demands plus losses
  3. Domestic, public and commercial demands, with fire demand and losses excluded
  4. Domestic and fire demands only, with industrial, public and losses excluded
Show answer & solution

Answer: (B) Domestic, industrial, commercial, public and fire demands plus losses

Per capita demand (lpcd) is the total annual requirement, including domestic, industrial, commercial, public use, fire demand and losses, divided by population and days.

Question 26

What is the main purpose of population forecasting in water supply and sewerage planning?

  1. To estimate the future chemical quality of the raw water source
  2. To estimate design-year population and hence future demand
  3. To fix the number of bacteriological tests needed each month
  4. To decide the pipe material for the whole distribution network
Show answer & solution

Answer: (B) To estimate design-year population and hence future demand

Design flows are based on the population expected at the end of the design period, found by forecasting.

Question 27

The main function of a water distribution system is to

  1. deliver treated water from the plant or clear-water reservoir to consumers at adequate pressure
  2. remove impurities from raw water by coagulation, sedimentation and filtration before supply
  3. collect used water from households and carry it to a treatment works for safe disposal
  4. store flood water in a large reservoir so that irrigation of crops can continue in dry seasons
Show answer & solution

Answer: (A) deliver treated water from the plant or clear-water reservoir to consumers at adequate pressure

Distribution = conveyance, storage and delivery of treated water; treatment and sewerage are separate systems.

Question 28

Leakage from old distribution mains adds to non-revenue water mainly because

  1. treated water, produced at a cost, is lost before it reaches a billed consumer
  2. leaked water is billed at double the normal tariff
  3. leakage only affects quality, not the quantity delivered
  4. the lost water was never treated, so leakage carries no cost for the utility to recover
Show answer & solution

Answer: (A) treated water, produced at a cost, is lost before it reaches a billed consumer

Leakage is a physical loss of already-treated and pumped water, so the utility loses both water and the production cost.

Question 29

Why must a water distribution system be properly operated and maintained, even after the source and treatment plant are built?

  1. It matters only for large national-level utilities, because local schemes are too small to suffer losses
  2. Otherwise leakage, poor service and weak revenue recovery undermine the investment in source and treatment
  3. It lets the utility skip treatment and source development entirely once the network is laid
  4. It affects only the appearance of the pipes, while long-term supply performance depends on the design alone
Show answer & solution

Answer: (B) Otherwise leakage, poor service and weak revenue recovery undermine the investment in source and treatment

O&M keeps leakage (NRW), pressures, water quality and revenue at acceptable levels so that the supply remains sustainable.

Question 30

The geometric increase method of population forecasting assumes that the population

  1. increases by a constant absolute number each decade
  2. increases by a decreasing percentage as the population grows
  3. remains constant after the first decade
  4. increases by a constant percentage (growth rate) each decade
Show answer & solution

Answer: (D) increases by a constant percentage (growth rate) each decade

Geometric method: Pn = P0(1 + r/100)ⁿ, with r the average percentage growth per decade.

Question 31

The arithmetic increase method of population forecasting assumes that the population

  1. increases by an amount that doubles each decade
  2. increases at a rate proportional to the saturation deficit
  3. increases by a constant percentage each decade
  4. increases by a constant absolute number each decade
Show answer & solution

Answer: (D) increases by a constant absolute number each decade

Arithmetic method: Pn = P0 + n·x̄, with x̄ the average decadal increase.

Question 32

Which of the following is a group of groundwater (subsurface) sources of water supply?

  1. Rivers, canals and lakes
  2. Springs, infiltration galleries and wells
  3. Rivers, springs and tanks
  4. Ponds, streams and impounding reservoirs in normal practice
Show answer & solution

Answer: (B) Springs, infiltration galleries and wells

Springs, infiltration galleries and open/tube wells tap water below ground.

Question 33

The design period generally adopted for a water supply project (varying with the component) is about

  1. 2 to 5 years
  2. 15 to 30 years
  3. 50 to 75 years
  4. 100 to 150 years
Show answer & solution

Answer: (B) 15 to 30 years

Water supply components are commonly designed for 15–30 years (pipes and civil works longer, pumps and mechanical items shorter).

Question 34

Compared with a dead-end system, a grid-iron (looped) system offers the advantage that

  1. water can reach any point from more than one direction, so supply continues during repairs
  2. it is easier to design by simple hand calculations
  3. it needs fewer valves and a shorter total pipe length than a dead-end system of the same area
  4. stagnant water collects at every junction
Show answer & solution

Answer: (A) water can reach any point from more than one direction, so supply continues during repairs

Looping gives alternative flow paths, better pressures, no dead ends and easier maintenance, but needs more pipe and valves and a harder analysis (Hardy Cross).

Question 35

Arsenic in groundwater is a major concern mainly because

  1. it gives the water a strong taste and colour
  2. it makes the water hard and scale forming
  3. long-term intake causes acute cholera in children
  4. long-term intake causes skin lesions and cancers
Show answer & solution

Answer: (D) long-term intake causes skin lesions and cancers

Chronic arsenic exposure causes arsenicosis and cancers; the WHO guideline value is 10 µg/L.

Question 36

Which of the following lists the components of a complete water supply system in the correct order from source to consumer?

  1. Treatment, source, intake, distribution, conveyance
  2. Source, intake, conveyance, treatment, storage, distribution
  3. Source, distribution, treatment, intake, storage
  4. Intake, distribution, source, storage, treatment
Show answer & solution

Answer: (B) Source, intake, conveyance, treatment, storage, distribution

The system flows from the source through intake, conveyance, treatment, treated water storage to the distribution network.

Practice these 36 questions interactively →