Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Public Health Engineering: Sewage Treatment and Sludge Management

Civil Engineering · Public Health Engineering

39 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

Secondary treatment of sewage mainly relies on

  1. disinfection by ultraviolet light
  2. physical screening and sedimentation of the coarse and settleable solids in the sewage
  3. microorganisms that degrade dissolved and finely suspended organic matter
  4. chemical coagulation with alum
Show answer & solution

Answer: (C) microorganisms that degrade dissolved and finely suspended organic matter

Aerobic biological processes (activated sludge, trickling filter, ponds) remove most remaining BOD, typically 85-95%.

Question 2

Anaerobic treatment is best suited to

  1. dilute municipal sewage in all modern treatment plants, because it needs no energy input
  2. high-strength wastes and sewage sludge, with biogas (methane) recovery
  3. tertiary polishing of final effluent
  4. removal of grit and screenings
Show answer & solution

Answer: (B) high-strength wastes and sewage sludge, with biogas (methane) recovery

Anaerobic digesters handle strong organic loads and produce methane.

Question 3

Odour control is important at a sewage treatment plant mainly because

  1. odours raise the dissolved oxygen of the final effluent
  2. odours increase the pH of the sludge in the digester
  3. odours reduce the BOD removal efficiency of the aeration tank
  4. odours annoy nearby residents and H₂S endangers workers
Show answer & solution

Answer: (D) odours annoy nearby residents and H₂S endangers workers

Hydrogen sulphide and other odorous gases cause public nuisance and are toxic and corrosive.

Question 4

Sewage treatment is generally organized into

  1. a single stage of settling followed directly by discharge, with no distinction between levels
  2. preliminary, secondary and sludge treatment, where tertiary treatment replaces primary settling
  3. coagulation, filtration and disinfection only, as in the treatment of drinking water
  4. preliminary and primary treatment, secondary treatment, and tertiary treatment where required
Show answer & solution

Answer: (D) preliminary and primary treatment, secondary treatment, and tertiary treatment where required

Preliminary/primary are physical, secondary is biological, tertiary is advanced polishing.

Question 5

A soil absorption (leach) field following a septic tank serves to

  1. collect storm water around the house
  2. disinfect the effluent with chlorine
  3. settle the solids before the septic tank, so that the tank receives only clarified liquid
  4. treat and dispose of septic tank effluent by percolation through soil
Show answer & solution

Answer: (D) treat and dispose of septic tank effluent by percolation through soil

Effluent is polished by soil filtration and biological activity as it percolates.

Question 6

Nutrient removal in sewage treatment is important mainly when

  1. the receiving water body is prone to eutrophication
  2. the effluent has already been disinfected with chlorine
  3. the effluent will be used only for industrial cooling
  4. the sewage has very low BOD
Show answer & solution

Answer: (A) the receiving water body is prone to eutrophication

N and P discharge drives algal blooms in lakes, reservoirs and slow rivers.

Question 7

Which of the following is a common final disposal or reuse option for treated sewage sludge?

  1. Blending with the raw water at the treatment plant intake
  2. Discharge into a river after only coarse screening
  3. Storage in open lagoons with no later disposal planned
  4. Land application, landfilling or incineration
Show answer & solution

Answer: (D) Land application, landfilling or incineration

Treated sludge is applied to land, landfilled or incinerated, depending on its quality and local conditions.

Question 8

Constructed wetlands treat wastewater through

  1. rotating discs carrying a biofilm
  2. combined physical, chemical and biological processes in engineered vegetated beds
  3. chlorine contact in baffled tanks
  4. activated sludge in a deep aeration tank, with sludge returned from the final clarifier
Show answer & solution

Answer: (B) combined physical, chemical and biological processes in engineered vegetated beds

Plants, soil and microbes remove BOD, suspended solids and nutrients, mimicking natural wetlands.

Question 9

Mixed liquor suspended solids (MLSS) is the

  1. dissolved solids in the final effluent
  2. oxygen concentration in the aeration tank
  3. concentration of suspended solids in the raw influent sewage entering the plant inlet works
  4. concentration of suspended solids, mainly biomass, in the aeration tank
Show answer & solution

Answer: (D) concentration of suspended solids, mainly biomass, in the aeration tank

MLSS in conventional activated sludge is typically about 2000-3500 mg/L.

Question 10

Tertiary (advanced) treatment of sewage is used to

  1. remove nutrients, remaining suspended solids and pathogens beyond secondary level
  2. remove grit and large debris at the plant inlet before the sewage enters the primary tank
  3. achieve no further removal beyond secondary level
  4. remove only settleable solids by sedimentation
Show answer & solution

Answer: (A) remove nutrients, remaining suspended solids and pathogens beyond secondary level

Examples: nutrient removal, filtration, disinfection, membranes.

Question 11

Excess (waste) activated sludge is

  1. discharged untreated with the final effluent to the receiving stream after chlorination
  2. kept in the aeration tank permanently, because wasting would reduce the active biomass
  3. removed periodically for sludge treatment and disposal to keep aeration tank solids in range
  4. returned entirely to the primary tank, so that no sludge leaves the plant
Show answer & solution

Answer: (C) removed periodically for sludge treatment and disposal to keep aeration tank solids in range

Wasting controls sludge age (mean cell residence time) and prevents solids build-up.

Question 12

The main purpose of sludge thickening is to

  1. destroy the pathogens in the sludge by prolonged heating
  2. produce a dry sludge cake that is fit for direct landfilling
  3. convert the organic solids in the sludge into methane gas
  4. increase the solids concentration and reduce the sludge volume
Show answer & solution

Answer: (D) increase the solids concentration and reduce the sludge volume

Thickening (gravity or flotation) removes part of the water, reducing the volume to be digested or dewatered.

Question 13

The biofilm on trickling filter media periodically

  1. turns into grit and is removed in a grit chamber
  2. sloughs off and is removed from the effluent in a secondary settling tank
  3. stays on the media permanently, so that the effluent contains no biological solids at all
  4. gets returned in full to the filter inlet
Show answer & solution

Answer: (B) sloughs off and is removed from the effluent in a secondary settling tank

Sloughed humus is settled in the final clarifier before discharge.

Question 14

The basic objective of sewage treatment is to

  1. increase the BOD of the sewage before discharge so that the stream can self-purify faster
  2. remove only the visible colour and odour of the sewage before it is discharged
  3. reduce organic matter, suspended solids and pathogens to levels acceptable for disposal or reuse
  4. convert all sewage into potable water for direct supply to consumers
Show answer & solution

Answer: (C) reduce organic matter, suspended solids and pathogens to levels acceptable for disposal or reuse

Treatment protects public health and the receiving water body to meet effluent standards (e.g. NEQS in Pakistan).

Question 15

The main purpose of sludge dewatering is to

  1. reduce the water content to give a handleable sludge cake
  2. reduce the BOD of the supernatant returned to the plant
  3. break down the organic matter in the sludge to biogas
  4. remove the dissolved salts present in the sludge liquor
Show answer & solution

Answer: (A) reduce the water content to give a handleable sludge cake

Dewatering (drying beds, filter presses, centrifuges) lowers moisture so the sludge can be handled and transported.

Question 16

Primary sedimentation alone typically gives

  1. partial removal of suspended solids and BOD, leaving finer and dissolved organics for secondary treatment
  2. complete removal of BOD and suspended solids, so no further treatment is needed before discharge
  3. removal of nearly all dissolved organic matter, with suspended solids passing through unchanged
  4. complete removal of pathogens, so that disinfection is unnecessary before discharge
Show answer & solution

Answer: (A) partial removal of suspended solids and BOD, leaving finer and dissolved organics for secondary treatment

Typical removal is about 50-65% SS and 25-40% BOD; effluent still needs biological treatment.

Question 17

A grit chamber is designed to remove

  1. heavy inorganic particles such as sand and gravel, which settle faster than organic solids
  2. light organic suspended solids, which settle slowly and need a long detention time
  3. pathogenic organisms, by contact with chlorine in a long, narrow channel
  4. dissolved organic matter, by biological action on the surface of the settled grit
Show answer & solution

Answer: (A) heavy inorganic particles such as sand and gravel, which settle faster than organic solids

Grit chambers are designed for a horizontal velocity of about 0.3 m/s to settle grit (≥ 0.2 mm) while keeping organics in suspension.

Question 18

Disinfection methods used on treated sewage (chlorine, UV, ozone) are the same in principle as those used for

  1. sludge dewatering by belt presses and centrifuges at the plant
  2. screening of coarse solids at the inlet works with mechanically raked bar screens
  3. grit removal in aerated grit chambers at the inlet works of the plant
  4. drinking water disinfection
Show answer & solution

Answer: (D) drinking water disinfection

The disinfection mechanism (inactivating pathogens) is the same; doses and contact conditions differ.

Question 19

Sludge drying beds dewater sludge mainly by

  1. drainage through a sand-gravel bed together with evaporation
  2. mechanical pressing of the sludge between two moving belts
  3. centrifugal force generated in a rotating solid bowl
  4. chemical oxidation of the sludge solids with lime dosing
Show answer & solution

Answer: (A) drainage through a sand-gravel bed together with evaporation

Sludge on a drying bed loses water by percolation through the sand/gravel underdrain and by evaporation.

Question 20

Which factors decide the required treatment level for sewage effluent reused in irrigation?

  1. only the age and design capacity of the treatment plant that produced the effluent
  2. the crop type, the irrigation method, and the likelihood of human exposure to pathogens
  3. only the colour of the effluent and the age of the treatment plant that produced it
  4. the discharge permit of the nearest industry and the BOD of the receiving stream
Show answer & solution

Answer: (B) the crop type, the irrigation method, and the likelihood of human exposure to pathogens

WHO reuse guidelines relate treatment and pathogen limits to crop type (e.g. raw-eaten vegetables vs. fodder) and exposure.

Question 21

A trickling filter treats sewage by

  1. mixing sewage with a suspended biomass culture in a tank supplied with diffused air
  2. settling sewage in a quiescent tank for removal of grit
  3. letting settled sewage trickle over media coated with a biological film
  4. holding sewage in shallow ponds under sunlight
Show answer & solution

Answer: (C) letting settled sewage trickle over media coated with a biological film

Attached-growth (fixed-film) process; the biofilm oxidizes organics as the sewage flows down the bed.

Question 22

A septic tank provides

  1. filtration of sewage through sand beds, followed by chlorination before discharge
  2. sedimentation and anaerobic digestion in an underground tank, with the effluent needing further disposal
  3. complete aerobic treatment, so that the effluent needs no further treatment or disposal at all
  4. only chlorination and screening of sewage for small houses before disposal
Show answer & solution

Answer: (B) sedimentation and anaerobic digestion in an underground tank, with the effluent needing further disposal

Typical detention is 1-3 days, with effluent to a soakage pit or dispersion trench; BOD removal is only about 30-50%.

Question 23

Preliminary treatment of sewage includes

  1. activated sludge and trickling filtration to remove the dissolved organic load
  2. screening and grit removal to protect downstream units
  3. anaerobic digestion of sludge
  4. chlorination and dechlorination
Show answer & solution

Answer: (B) screening and grit removal to protect downstream units

Screens remove floating debris; grit chambers remove sand and heavy inorganics.

Question 24

Sludge management is a major aspect of sewage treatment plant operation mainly because

  1. it has almost no influence on plant operating cost or staffing
  2. it is a large share of plant cost and poor handling harms liquid treatment
  3. it affects only the colour and odour of the final effluent
  4. it matters only for very large industrial wastewater treatment plants in normal practice
Show answer & solution

Answer: (B) it is a large share of plant cost and poor handling harms liquid treatment

Sludge handling often accounts for a large share of treatment cost, and poor handling returns pollutants to the system.

Question 25

A complete and effective sewage treatment system must be designed to deal with

  1. both the liquid effluent and the resulting sludge
  2. the liquid effluent only, since sludge is harmless
  3. the sludge only, since effluent needs no treatment
  4. the screenings only, since other solids settle naturally
Show answer & solution

Answer: (A) both the liquid effluent and the resulting sludge

Treatment produces both a liquid stream and sludge; both need proper processing and disposal.

Question 26

Primary treatment of sewage consists mainly of

  1. biological oxidation in an aeration tank followed by final clarification of the sludge
  2. nutrient removal by chemical precipitation
  3. chlorine contact for disinfection
  4. sedimentation in primary tanks to remove settleable solids and part of the BOD
Show answer & solution

Answer: (D) sedimentation in primary tanks to remove settleable solids and part of the BOD

Primary sedimentation removes about 60% of SS and 30-35% of BOD.

Question 27

Sewage sludge requires further treatment before disposal mainly because it

  1. loses all its pathogens during primary settling alone
  2. is mostly inorganic and already chemically stable on discharge
  3. contains too much dissolved oxygen to be disposed of safely
  4. still holds much putrescible organic matter and many pathogens
Show answer & solution

Answer: (D) still holds much putrescible organic matter and many pathogens

Raw sludge is organic-rich, odorous and pathogenic, so it must be stabilised and dewatered before disposal or reuse.

Question 28

Return activated sludge (RAS) is

  1. settled sludge from the secondary clarifier returned to the aeration tank to maintain biomass
  2. sludge discharged from the secondary clarifier for final disposal in a drying bed or landfill
  3. raw sewage recycled to the plant inlet
  4. grit returned from the grit chamber to the sewer
Show answer & solution

Answer: (A) settled sludge from the secondary clarifier returned to the aeration tank to maintain biomass

RAS maintains the required MLSS and food-to-microorganism ratio in the aeration tank.

Question 29

Reuse of treated sewage effluent in water-scarce regions helps to

  1. increase demand on freshwater sources by supplying lower-quality water for irrigation
  2. avoid sewage treatment altogether by applying raw sewage directly to land and crops
  3. augment water resources by using what would otherwise be a wasted or polluting stream
  4. avoid any need for water quality guidelines because treated effluent is always safe
Show answer & solution

Answer: (C) augment water resources by using what would otherwise be a wasted or polluting stream

Reuse for irrigation, industry or landscaping conserves freshwater, as in WHO guidelines for wastewater use.

Question 30

A package sewage treatment plant is characterized by

  1. several treatment processes combined in one factory-built unit for small communities or institutions
  2. inability to achieve any treatment, whatever the design, because the unit is too small
  3. absence of any biological treatment step, with settling and chlorination only
  4. an identical design to a large conventional plant, built on site in concrete
Show answer & solution

Answer: (A) several treatment processes combined in one factory-built unit for small communities or institutions

Package plants (often extended aeration) serve small flows such as hotels, hospitals and campuses.

Question 31

The main purpose of sludge digestion is to

  1. remove grit and sand so that the sludge can be pumped easily
  2. raise the solids content to above 50 percent by evaporation
  3. dilute the sludge so that it can be discharged into streams
  4. stabilise organic matter, cutting pathogens and odour, giving biogas
Show answer & solution

Answer: (D) stabilise organic matter, cutting pathogens and odour, giving biogas

Anaerobic digestion breaks down biodegradable organics, producing methane-rich biogas and a stabilised sludge.

Question 32

Disinfection of treated sewage effluent serves mainly to

  1. remove grit from the effluent
  2. reduce pathogens to lower the health risk from the receiving water or reuse
  3. replace secondary treatment
  4. reduce the BOD by biological oxidation, so that secondary treatment may be left out
Show answer & solution

Answer: (B) reduce pathogens to lower the health risk from the receiving water or reuse

Chlorination, UV or ozone are used for final polishing.

Question 33

Which factor is most important to check before applying treated sewage sludge to agricultural land?

  1. Sludge volume and the distance to the nearest town centre
  2. Sludge colour, odour and the transport distance to the field
  3. Sludge quality (pathogens, metals), loading rate and crop
  4. Sludge temperature and the type of hauling vehicle used
Show answer & solution

Answer: (C) Sludge quality (pathogens, metals), loading rate and crop

Land application depends on pathogen and metal content, loading rate and crop use to protect health and soil.

Question 34

A main advantage of oxidation ponds compared with mechanical plants is

  1. a very small land requirement, although operating and energy costs are comparatively high
  2. shorter detention time than activated sludge
  3. low operating cost and simple operation, although much more land is needed
  4. no dependence on sunlight or climate
Show answer & solution

Answer: (C) low operating cost and simple operation, although much more land is needed

Ponds suit warm climates like most of Pakistan and small towns with cheap land.

Question 35

In the activated sludge process, sewage is

  1. passed over fixed media carrying a biological film
  2. held for weeks in shallow ponds without aeration
  3. mixed with active microorganisms in an aeration tank, then settled in a secondary clarifier
  4. settled in a primary tank and then discharged directly to the receiving stream without aeration
Show answer & solution

Answer: (C) mixed with active microorganisms in an aeration tank, then settled in a secondary clarifier

Aeration tank gives biological oxidation; final settling separates the biomass, part of which is returned.

Question 36

What do the various sewage treatment technologies show about selecting one for a community?

  1. No technology is best everywhere; the choice depends on site-specific technical and economic factors
  2. Only one technology is ever appropriate, and it should be applied to every community
  3. Technology choice is unrelated to site conditions, since effluent standards fix the process
  4. Most technologies are interchangeable, so the cheapest can be chosen without further study
Show answer & solution

Answer: (A) No technology is best everywhere; the choice depends on site-specific technical and economic factors

Selection depends on effluent standards, land, cost, skills and climate.

Question 37

Compared with the activated sludge process, a trickling filter generally

  1. needs less land and gives higher BOD removal
  2. uses the same energy and land area as activated sludge
  3. uses less energy for aeration but needs more land and has its own operational limits
  4. needs far more energy because of larger blowers, but needs much less land than activated sludge
Show answer & solution

Answer: (C) uses less energy for aeration but needs more land and has its own operational limits

Trickling filters rely on natural ventilation, so power demand is low, but they are bulky and prone to odour and fly nuisance.

Question 38

Oxidation (stabilization) ponds treat sewage mainly through

  1. chemical precipitation and filtration of the wastewater through a coarse sand bed
  2. fixed-film media in rotating drums, with a short contact time and forced aeration
  3. mechanical aerators and recycled sludge in deep tanks with short detention times
  4. natural action of bacteria and algae with sunlight, in shallow ponds with long detention times
Show answer & solution

Answer: (D) natural action of bacteria and algae with sunlight, in shallow ponds with long detention times

Symbiosis: algae provide oxygen by photosynthesis, bacteria decompose organics.

Question 39

A rotating biological contactor (RBC) consists of

  1. a settling tank fitted with a scraper mechanism
  2. a deep tank with diffused air and suspended floc
  3. closely spaced discs on a horizontal shaft, partly submerged and slowly rotated through the sewage
  4. a bed of stones or plastic media over which settled sewage is sprayed by rotating distributor arms
Show answer & solution

Answer: (C) closely spaced discs on a horizontal shaft, partly submerged and slowly rotated through the sewage

A fixed-film process; the biofilm alternately contacts sewage and air.

Practice these 39 questions interactively →