What is the Rankine cycle?
Show answer & solution
Answer: (A) The ideal cycle for steam power plants with pump, boiler, turbine and condenser
Most thermal power plants use it.
Chemical Engineering · Chemical Engineering Thermodynamics
38 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the Rankine cycle?
Answer: (A) The ideal cycle for steam power plants with pump, boiler, turbine and condenser
Most thermal power plants use it.
How does superheating steam affect the Rankine cycle?
Answer: (B) It raises efficiency and reduces moisture at the turbine exhaust
Turbine exhaust quality should be above about 88–90%.
What is the purpose of reheating in a Rankine cycle?
Answer: (D) To reduce moisture in later turbine stages and improve efficiency
Steam is returned to the boiler after partial expansion.
What is regenerative feedwater heating?
Answer: (C) Heating feedwater with steam bled from the turbine to raise cycle efficiency
It raises the mean temperature of heat addition.
How does lowering condenser pressure affect Rankine cycle efficiency?
Answer: (B) It increases efficiency
It lowers the heat rejection temperature.
What is the Brayton cycle?
Answer: (A) The ideal gas turbine cycle with compression, constant-pressure heating, expansion and constant-pressure cooling
Gas turbines power many combined-cycle plants.
What is the efficiency of an ideal Brayton cycle with pressure ratio rp?
Answer: (C) 1 − 1/rp^((γ−1)/γ)
Efficiency rises with pressure ratio.
What is a combined-cycle power plant?
Answer: (D) A gas turbine whose hot exhaust raises steam in a heat recovery boiler for a steam turbine
Efficiencies near 60% are possible; several Pakistani RLNG plants use it.
What is the Otto cycle?
Answer: (B) The ideal cycle for spark-ignition engines with constant-volume heat addition
Efficiency = 1 − 1/r^(γ−1).
What is the Diesel cycle?
Answer: (A) The ideal cycle for compression-ignition engines with constant-pressure heat addition
Diesel engines use higher compression ratios.
What are the main components of a vapour compression refrigeration cycle?
Answer: (C) Compressor, condenser, expansion valve and evaporator
Refrigerant absorbs heat in the evaporator.
What happens to the refrigerant in the evaporator of a refrigeration cycle?
Answer: (D) It boils at low pressure, absorbing heat from the cooled space
The evaporator is the cold side.
What process takes place in the expansion valve of a vapour compression refrigerator?
Answer: (A) Throttling at constant enthalpy
Pressure and temperature fall.
What is the COP of a refrigerator that removes 5 kW of heat using 1.25 kW of compressor work?
Answer: (B) 4
COP = 5/1.25.
What is one ton of refrigeration?
Answer: (B) About 3.517 kW of cooling
It equals 12,000 BTU/h.
What is the principle of an absorption refrigeration system?
Answer: (A) A heat-driven generator and absorber replace the mechanical compressor
Ammonia–water and lithium bromide–water systems are common.
Which refrigerants are being phased out under the Montreal Protocol because they deplete ozone?
Answer: (C) CFCs such as R-12 and HCFCs such as R-22
HFCs are being reduced under the Kigali Amendment.
What is a heat pump?
Answer: (D) A device that uses work to move heat from a cold source to a warm space for heating
Its COP is higher than that of the same machine as a refrigerator by 1.
What is the Linde process used for?
Answer: (D) Liquefaction of gases using Joule–Thomson expansion after compression and precooling
Claude's process adds an expansion engine.
What is the main use of a T–s diagram for cycles?
Answer: (B) Showing heat transfer as areas and identifying irreversibilities
The area enclosed equals net work for a reversible cycle.
What is the thermal efficiency of a power plant producing 400 MW from 1,000 MW of fuel heat?
Answer: (C) 40%
η = 400/1,000.
What is heat rate in power plants?
Answer: (A) The fuel energy used per unit of electrical energy produced
Lower heat rate means higher efficiency.
Why is ammonia widely used as an industrial refrigerant in Pakistani cold stores and ice plants?
Answer: (C) It has excellent thermodynamic properties and no ozone depletion potential
Its toxicity requires careful leak management.
What is the efficiency of an ideal Otto cycle with compression ratio 8 and γ = 1.4?
Answer: (B) About 56.5%
1 − 1/8^0.4 = 1 − 0.435.
Why does a diesel engine use a higher compression ratio than a petrol engine?
Answer: (D) Fuel is ignited by the heat of compression, so high compression is needed and knocking is not a limit
Typical ratios are 14–22 for diesel and 8–12 for petrol.
What is the function of the condenser in a steam power plant?
Answer: (A) To condense turbine exhaust steam at low pressure so that it can be pumped back to the boiler
Cooling water or air removes the latent heat.
What is the pump work in a Rankine cycle compared with turbine work?
Answer: (C) Very small, because liquid water has a small specific volume
Gas turbine compressors take a much larger fraction of work.
What is the back work ratio?
Answer: (B) The ratio of compressor (or pump) work to turbine work
It is high in gas turbines, often 40–60%.
What is the purpose of a deaerator in a steam plant?
Answer: (C) To remove dissolved oxygen and CO₂ from feedwater to prevent corrosion
It is an open feedwater heater.
What is the role of the generator in an absorption refrigeration system?
Answer: (D) To heat the strong solution and drive off refrigerant vapour
Low-grade heat or steam can drive it.
Which refrigerant pair is used in lithium bromide absorption chillers?
Answer: (A) Water as refrigerant and lithium bromide as absorbent
They cannot cool below 0 °C since water is the refrigerant.
What is subcooling in a refrigeration cycle?
Answer: (C) Cooling the liquid refrigerant below its saturation temperature before the expansion valve
It increases refrigerating effect.
What is the refrigerating effect per kg of refrigerant?
Answer: (D) The enthalpy rise of refrigerant across the evaporator
COP = refrigerating effect/compressor work.
What is cogeneration?
Answer: (A) Simultaneous production of electricity and useful heat from one fuel source
Sugar mills in Pakistan cogenerate power from bagasse.
What is the purpose of a steam turbine's extraction steam in process industries?
Answer: (B) To supply steam at intermediate pressure for process heating
Extraction–condensing turbines are common in refineries and sugar mills.
What is the effect of increasing boiler pressure (at fixed maximum temperature) on Rankine efficiency?
Answer: (A) Efficiency increases, but turbine exhaust moisture also increases
Reheating counters the moisture increase.
What is the ideal Brayton efficiency with a pressure ratio of 10 and γ = 1.4?
Answer: (B) About 48%
1 − 10^(−0.2857) = 1 − 0.518.
What is intercooling in a gas turbine cycle used for?
Answer: (A) Reducing compressor work by cooling air between compression stages
Regeneration uses exhaust heat to preheat compressed air.