Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Chemical Engineering Thermodynamics: Phase Equilibria

Chemical Engineering · Chemical Engineering Thermodynamics

34 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the criterion for phase equilibrium of a component between two phases?

  1. Equal densities
  2. Equal chemical potentials (or fugacities) in both phases at the same T and P
  3. Equal enthalpies
  4. Equal concentrations
Show answer & solution

Answer: (B) Equal chemical potentials (or fugacities) in both phases at the same T and P

The criterion is applied to each component.

Question 2

What is the modified Raoult's law?

  1. yi P = xi γi Pi^sat
  2. yi P = xi Pi^sat only
  3. P = Σ Pi^sat
  4. yi = xi
Show answer & solution

Answer: (A) yi P = xi γi Pi^sat

γi is the activity coefficient.

Question 3

What is the activity coefficient?

  1. The vapour pressure
  2. The fugacity coefficient of a gas
  3. The ratio of the actual fugacity in solution to the ideal-solution fugacity
  4. The ratio of pressures
Show answer & solution

Answer: (C) The ratio of the actual fugacity in solution to the ideal-solution fugacity

It equals 1 for an ideal solution.

Question 4

What does an activity coefficient greater than 1 indicate?

  1. Ideal behaviour
  2. Positive deviation from Raoult's law
  3. Solid formation
  4. Negative deviation
Show answer & solution

Answer: (B) Positive deviation from Raoult's law

Unlike molecules repel relative to like molecules.

Question 5

Which activity coefficient models are widely used for VLE?

  1. Margules, van Laar, Wilson, NRTL and UNIQUAC
  2. Dittus–Boelter and Sieder–Tate
  3. Antoine and Clausius–Clapeyron
  4. Peng–Robinson only
Show answer & solution

Answer: (A) Margules, van Laar, Wilson, NRTL and UNIQUAC

UNIFAC predicts parameters from group contributions.

Question 6

Which activity coefficient model can predict values from functional groups without experimental data?

  1. Margules
  2. van Laar
  3. Henry's law
  4. UNIFAC
Show answer & solution

Answer: (D) UNIFAC

It is used for screening when data are lacking.

Question 7

Which model cannot predict liquid–liquid phase splitting?

  1. NRTL
  2. Wilson equation
  3. UNIQUAC
  4. Margules
Show answer & solution

Answer: (B) Wilson equation

NRTL and UNIQUAC are used for LLE.

Question 8

What is the K-value in vapour–liquid equilibrium?

  1. The thermal conductivity
  2. The Henry's constant
  3. The equilibrium constant of reaction
  4. The ratio yi/xi for a component
Show answer & solution

Answer: (D) The ratio yi/xi for a component

For ideal systems Ki = Pi^sat/P.

Question 9

Which charts give K-values for light hydrocarbons as functions of temperature and pressure?

  1. DePriester charts
  2. Cox charts
  3. Moody charts
  4. Heisler charts
Show answer & solution

Answer: (A) DePriester charts

They are widely used in gas processing.

Question 10

What is a bubble point calculation?

  1. Finding where the last liquid vaporises
  2. Finding critical properties
  3. Finding the temperature or pressure at which a liquid of known composition begins to boil
  4. Finding reaction equilibrium
Show answer & solution

Answer: (C) Finding the temperature or pressure at which a liquid of known composition begins to boil

Σ Ki xi = 1.

Question 11

What does a flash calculation find?

  1. The heat of reaction
  2. The critical point only
  3. The bubble point only
  4. The fractions and compositions of vapour and liquid at given T and P
Show answer & solution

Answer: (D) The fractions and compositions of vapour and liquid at given T and P

The Rachford–Rice equation is solved.

Question 12

What does Gibbs' phase rule give for a single-component system with two phases in equilibrium?

  1. One degree of freedom
  2. Zero degrees of freedom
  3. Three degrees of freedom
  4. Two degrees of freedom
Show answer & solution

Answer: (A) One degree of freedom

F = 1 − 2 + 2; fixing T fixes P.

Question 13

What is a positive azeotrope?

  1. An ideal mixture
  2. A maximum-boiling azeotrope
  3. A minimum-boiling (maximum-pressure) azeotrope from positive deviation
  4. A solid solution
Show answer & solution

Answer: (C) A minimum-boiling (maximum-pressure) azeotrope from positive deviation

Ethanol–water is an example.

Question 14

At an azeotrope, what is true of the vapour and liquid compositions?

  1. Liquid is pure
  2. They are equal
  3. They are unrelated
  4. Vapour is richer in the heavy component
Show answer & solution

Answer: (B) They are equal

Relative volatility equals 1.

Question 15

What is retrograde condensation?

  1. Condensation by cooling only
  2. Boiling at constant pressure
  3. Freezing of gas
  4. Liquid formation on lowering pressure of a gas condensate above its critical point region
Show answer & solution

Answer: (D) Liquid formation on lowering pressure of a gas condensate above its critical point region

It occurs in gas condensate reservoirs.

Question 16

What is the cricondentherm?

  1. The minimum temperature
  2. The maximum temperature at which two phases can exist for a mixture
  3. The bubble point
  4. The critical temperature
Show answer & solution

Answer: (B) The maximum temperature at which two phases can exist for a mixture

The cricondenbar is the maximum pressure for two phases.

Question 17

What is the equilibrium criterion between liquid and solid in solubility calculations?

  1. Equal volumes
  2. Equal densities
  3. Equal fugacities of the solute in solid and liquid phases
  4. Equal enthalpies
Show answer & solution

Answer: (C) Equal fugacities of the solute in solid and liquid phases

It gives the ideal solubility equation.

Question 18

What is the condition for liquid–liquid equilibrium?

  1. Equal activities (xi γi) of each component in both liquid phases
  2. Equal vapour pressures
  3. Equal mole fractions
  4. Equal densities
Show answer & solution

Answer: (A) Equal activities (xi γi) of each component in both liquid phases

This defines the tie lines.

Question 19

What is Henry's law constant used for in phase equilibrium?

  1. Describing reaction rates
  2. Describing a pure gas
  3. Describing fugacity of a dilute solute in a liquid
  4. Describing a pure solvent
Show answer & solution

Answer: (C) Describing fugacity of a dilute solute in a liquid

It applies when the solute is near infinite dilution.

Question 20

What is the Lewis–Randall rule?

  1. In an ideal solution, the fugacity of a component equals its mole fraction times the pure-component fugacity
  2. Fugacity equals pressure
  3. Activity equals concentration
  4. Vapour pressure is constant
Show answer & solution

Answer: (A) In an ideal solution, the fugacity of a component equals its mole fraction times the pure-component fugacity

It defines the ideal solution.

Question 21

What is a thermodynamic consistency test of VLE data based on?

  1. Fick's law
  2. Fourier's law
  3. The ideal gas law
  4. The Gibbs–Duhem equation
Show answer & solution

Answer: (D) The Gibbs–Duhem equation

The area test is one example.

Question 22

What is the boiling point of a solution of non-volatile solute compared with pure solvent?

  1. Equal
  2. Higher
  3. Lower
  4. Undefined
Show answer & solution

Answer: (B) Higher

This is boiling point elevation.

Question 23

What is a gas hydrate?

  1. A solution of gas in oil
  2. An ice-like solid of water cages enclosing gas molecules such as methane
  3. A liquid hydrocarbon
  4. A dissolved salt
Show answer & solution

Answer: (B) An ice-like solid of water cages enclosing gas molecules such as methane

Hydrates can block gas pipelines; glycol or methanol inhibits them.

Question 24

What is the relative volatility of an ideal binary system?

  1. The ratio of pure-component vapour pressures
  2. The ratio of densities
  3. The ratio of mole fractions
  4. The ratio of boiling points
Show answer & solution

Answer: (A) The ratio of pure-component vapour pressures

α = P₁^sat/P₂^sat.

Question 25

What is the total pressure of an ideal binary liquid with x₁ = 0.4, P₁^sat = 100 kPa and P₂^sat = 50 kPa?

  1. 40 kPa
  2. 70 kPa
  3. 75 kPa
  4. 150 kPa
Show answer & solution

Answer: (B) 70 kPa

P = 0.4 × 100 + 0.6 × 50.

Question 26

What is the vapour mole fraction y₁ in the same ideal mixture (x₁ = 0.4, P₁^sat = 100 kPa, P = 70 kPa)?

  1. About 0.286
  2. About 0.40
  3. About 0.571
  4. About 0.70
Show answer & solution

Answer: (C) About 0.571

y₁ = 40/70.

Question 27

What does a negative deviation from Raoult's law indicate?

  1. Ideal behaviour
  2. Weaker attraction between unlike molecules
  3. Immiscibility
  4. Stronger attraction between unlike molecules than between like molecules
Show answer & solution

Answer: (D) Stronger attraction between unlike molecules than between like molecules

Chloroform–acetone shows negative deviation.

Question 28

What is the dew point pressure calculation based on?

  1. Σ yi/Ki = 1
  2. Σ yi Ki = 0
  3. Σ xi = 0
  4. Σ Ki xi = 1
Show answer & solution

Answer: (A) Σ yi/Ki = 1

It finds where the first liquid forms.

Question 29

What does the gamma–phi approach to VLE use?

  1. Equations of state for both phases only
  2. Henry's law only
  3. Ideal behaviour for both phases
  4. Activity coefficients for the liquid and fugacity coefficients for the vapour
Show answer & solution

Answer: (D) Activity coefficients for the liquid and fugacity coefficients for the vapour

The phi–phi approach uses an equation of state for both phases.

Question 30

Why is the phi–phi (equation-of-state) approach preferred for hydrocarbon systems at high pressure?

  1. It is only for polar liquids
  2. It needs no parameters
  3. A single cubic equation can represent both phases near critical conditions
  4. It ignores pressure
Show answer & solution

Answer: (C) A single cubic equation can represent both phases near critical conditions

Peng–Robinson is common in gas processing simulators.

Question 31

What is the excess Gibbs energy of an ideal solution?

  1. Equal to RT
  2. Zero
  3. Negative always
  4. Positive always
Show answer & solution

Answer: (B) Zero

Activity coefficients equal 1, so G^E = RT Σ xi ln γi = 0.

Question 32

What is the infinite-dilution activity coefficient used for?

  1. Calculating vapour pressure
  2. Fitting activity coefficient model parameters and screening solvents
  3. Calculating critical points
  4. Calculating heat capacity
Show answer & solution

Answer: (B) Fitting activity coefficient model parameters and screening solvents

It reflects solute–solvent interaction strength.

Question 33

What is a eutectic in solid–liquid equilibrium?

  1. The composition and temperature at which liquid is in equilibrium with two solid phases
  2. The triple point of a pure substance
  3. A vapour–liquid azeotrope
  4. The critical point
Show answer & solution

Answer: (A) The composition and temperature at which liquid is in equilibrium with two solid phases

It is the lowest melting point of the mixture.

Question 34

How many phases can coexist at most in a two-component system at equilibrium?

  1. Two
  2. Five
  3. Four
  4. Three
Show answer & solution

Answer: (C) Four

F = 2 − P + 2 ≥ 0 gives P ≤ 4.

Practice these 34 questions interactively →