Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Plant Economics & Safety: Process Safety and Hazards

Chemical Engineering · Plant Economics & Safety

43 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What are the three elements of the fire triangle?

  1. Fuel, water and nitrogen
  2. Oxygen, water and steam
  3. Fuel, oxygen (oxidiser) and an ignition source (heat)
  4. Heat, nitrogen and CO₂
Show answer & solution

Answer: (C) Fuel, oxygen (oxidiser) and an ignition source (heat)

Removing any one prevents fire; the fire tetrahedron adds the chain reaction.

Question 2

What is the lower flammability limit (LFL)?

  1. The flash point
  2. The autoignition temperature
  3. The maximum fuel concentration
  4. The minimum concentration of fuel vapour in air that can propagate a flame
Show answer & solution

Answer: (D) The minimum concentration of fuel vapour in air that can propagate a flame

Below it the mixture is too lean to burn.

Question 3

What are the approximate flammability limits of methane in air?

  1. About 0.1% to 0.5%
  2. About 1% to 2%
  3. About 5% to 15% by volume
  4. About 50% to 80%
Show answer & solution

Answer: (C) About 5% to 15% by volume

Natural gas leaks within this range can explode.

Question 4

What are the approximate flammability limits of hydrogen in air?

  1. About 1% to 8%
  2. About 4% to 75% by volume
  3. About 5% to 15%
  4. About 50% to 60%
Show answer & solution

Answer: (B) About 4% to 75% by volume

Hydrogen has a very wide flammable range and low ignition energy.

Question 5

What is autoignition temperature?

  1. The lowest temperature at which a substance ignites spontaneously in air without an external flame
  2. The boiling point
  3. The fire point
  4. The flash point
Show answer & solution

Answer: (A) The lowest temperature at which a substance ignites spontaneously in air without an external flame

Hot surfaces above it can ignite leaks.

Question 6

What is the limiting oxygen concentration (LOC)?

  1. The oxygen concentration below which combustion is not possible
  2. The oxygen needed for breathing
  3. The oxygen in normal air
  4. The oxygen in flue gas
Show answer & solution

Answer: (A) The oxygen concentration below which combustion is not possible

Inerting keeps oxygen below LOC.

Question 7

What is inerting?

  1. Adding more air
  2. Heating equipment
  3. Cooling with water
  4. Replacing air in equipment with an inert gas such as nitrogen to prevent flammable mixtures
Show answer & solution

Answer: (D) Replacing air in equipment with an inert gas such as nitrogen to prevent flammable mixtures

It is used in reactors, tanks and centrifuges.

Question 8

What is a BLEVE?

  1. A dust explosion
  2. A boiling liquid expanding vapour explosion caused by rupture of a vessel containing liquid above its boiling point
  3. A pool fire
  4. A chemical reaction only
Show answer & solution

Answer: (B) A boiling liquid expanding vapour explosion caused by rupture of a vessel containing liquid above its boiling point

LPG tanks exposed to fire can BLEVE, often creating a fireball.

Question 9

What is a vapour cloud explosion (VCE)?

  1. A pool fire
  2. A jet fire
  3. A small fire
  4. An explosion from ignition of a large flammable vapour cloud in a congested area
Show answer & solution

Answer: (D) An explosion from ignition of a large flammable vapour cloud in a congested area

The Flixborough disaster (1974) was a cyclohexane VCE.

Question 10

What is a pool fire?

  1. A fire burning above a pool of flammable liquid
  2. A vapour cloud explosion
  3. A burning gas jet
  4. A dust explosion
Show answer & solution

Answer: (A) A fire burning above a pool of flammable liquid

Dikes limit pool size.

Question 11

What is a jet fire?

  1. A pool fire
  2. A flash fire
  3. A fire from a pressurised release of flammable gas or liquid burning as a jet
  4. A dust explosion
Show answer & solution

Answer: (C) A fire from a pressurised release of flammable gas or liquid burning as a jet

It can cause severe local heat damage.

Question 12

What are the five elements of the dust explosion pentagon?

  1. Fuel, water, heat, CO₂ and light
  2. Dust, water, steam, oil and gas
  3. Oxygen, nitrogen, argon, fuel and heat
  4. Fuel dust, oxygen, ignition source, dispersion and confinement
Show answer & solution

Answer: (D) Fuel dust, oxygen, ignition source, dispersion and confinement

Flour, sugar, coal and plastic dusts can explode.

Question 13

Why are bonding and earthing (grounding) used when transferring flammable liquids?

  1. To prevent build-up and discharge of static electricity
  2. To increase flow
  3. To heat the liquid
  4. To measure flow
Show answer & solution

Answer: (A) To prevent build-up and discharge of static electricity

Static sparks can ignite vapours.

Question 14

What is a flame arrester?

  1. A pressure relief valve
  2. A fire extinguisher
  3. A device that allows gas flow but stops flame propagation by cooling it in narrow passages
  4. A spark plug
Show answer & solution

Answer: (C) A device that allows gas flow but stops flame propagation by cooling it in narrow passages

It is used on tank vents and flare lines.

Question 15

What is the purpose of a pressure relief valve?

  1. Measuring pressure
  2. Protecting equipment from overpressure by releasing fluid automatically
  3. Isolating equipment
  4. Controlling flow continuously
Show answer & solution

Answer: (B) Protecting equipment from overpressure by releasing fluid automatically

It recloses when pressure falls.

Question 16

What is a runaway reaction?

  1. A slow reaction
  2. An endothermic reaction
  3. A reaction that stops
  4. An uncontrolled exothermic reaction where heat generation exceeds heat removal, accelerating temperature and pressure
Show answer & solution

Answer: (D) An uncontrolled exothermic reaction where heat generation exceeds heat removal, accelerating temperature and pressure

It caused the Seveso accident in 1976.

Question 17

What was released in the Bhopal disaster of 1984?

  1. Ammonia
  2. Methyl isocyanate (MIC)
  3. Dioxin
  4. Chlorine
Show answer & solution

Answer: (B) Methyl isocyanate (MIC)

It killed thousands and is the worst industrial disaster on record.

Question 18

What was released in the Seveso accident of 1976?

  1. Hydrogen sulphide
  2. Methyl isocyanate
  3. Dioxin (TCDD)
  4. Chlorine
Show answer & solution

Answer: (C) Dioxin (TCDD)

It led to the EU Seveso Directive on major hazards.

Question 19

What chemical caused the 2020 Beirut port explosion?

  1. Ammonium nitrate stored for years in a warehouse
  2. Chlorine
  3. LPG
  4. Methyl isocyanate
Show answer & solution

Answer: (A) Ammonium nitrate stored for years in a warehouse

Proper storage and inventory control are critical.

Question 20

Which HAZOP guide word combined with the parameter flow describes a complete absence of flow?

  1. Reverse
  2. Less
  3. No
  4. More
Show answer & solution

Answer: (C) No

Each guide word is applied systematically to every line and parameter.

Question 21

What is fault tree analysis (FTA)?

  1. A top-down method that works back from an undesired top event to combinations of causes using logic gates
  2. A bottom-up list of failures
  3. A cost analysis
  4. A fire test
Show answer & solution

Answer: (A) A top-down method that works back from an undesired top event to combinations of causes using logic gates

AND and OR gates combine basic events.

Question 22

What is event tree analysis (ETA)?

  1. A cost analysis
  2. A dust test
  3. A top-down analysis
  4. A forward method that traces possible outcomes from an initiating event through success or failure of safeguards
Show answer & solution

Answer: (D) A forward method that traces possible outcomes from an initiating event through success or failure of safeguards

It is used to estimate outcome frequencies.

Question 23

What is FMEA?

  1. A fire extinguisher type
  2. Failure modes and effects analysis, examining each component's failure modes and their effects
  3. A financial model
  4. A pipe code
Show answer & solution

Answer: (B) Failure modes and effects analysis, examining each component's failure modes and their effects

It is a bottom-up technique.

Question 24

What is the Dow Fire and Explosion Index used for?

  1. Measuring pressure
  2. Ranking relative fire and explosion hazards of process units
  3. Designing pumps
  4. Calculating costs
Show answer & solution

Answer: (B) Ranking relative fire and explosion hazards of process units

It considers material factor and process hazards.

Question 25

How is risk commonly defined in process safety?

  1. The product of the frequency of an event and the severity of its consequences
  2. The cost of insurance
  3. The frequency only
  4. The consequence only
Show answer & solution

Answer: (A) The product of the frequency of an event and the severity of its consequences

Risk matrices combine likelihood and severity.

Question 26

What does ALARP mean?

  1. A legal limit of zero risk
  2. As large as risk permits
  3. Always low and always reduced
  4. Risk reduced to as low as reasonably practicable
Show answer & solution

Answer: (D) Risk reduced to as low as reasonably practicable

Further reduction is required unless its cost is grossly disproportionate.

Question 27

What is the hierarchy of hazard controls?

  1. Training only
  2. PPE first, then elimination
  3. Elimination, substitution, engineering controls, administrative controls and PPE
  4. Insurance only
Show answer & solution

Answer: (C) Elimination, substitution, engineering controls, administrative controls and PPE

PPE is the last line of defence.

Question 28

What are the four colour sections of the NFPA 704 diamond?

  1. Red for health and blue for fire
  2. Blue for health, red for flammability, yellow for instability and white for special hazards
  3. Green for safety only
  4. Black for all hazards
Show answer & solution

Answer: (B) Blue for health, red for flammability, yellow for instability and white for special hazards

Ratings range from 0 to 4.

Question 29

What does a rating of 4 in the red section of the NFPA 704 diamond indicate?

  1. No fire hazard
  2. Moderate fire hazard
  3. Water reactivity
  4. Extreme flammability
Show answer & solution

Answer: (D) Extreme flammability

Gases such as hydrogen and propane are rated 4.

Question 30

What is the Swiss cheese model of accidents?

  1. Accidents occur when holes in several layers of defence line up
  2. Accidents are random
  3. Accidents have one cause
  4. Accidents happen only due to equipment
Show answer & solution

Answer: (A) Accidents occur when holes in several layers of defence line up

It was proposed by James Reason.

Question 31

What is the safety integrity level (SIL)?

  1. A pipe class
  2. A level of alarms
  3. A measure of the risk reduction provided by a safety instrumented function
  4. A tank level
Show answer & solution

Answer: (C) A measure of the risk reduction provided by a safety instrumented function

SIL 1 to 4, with 4 the highest.

Question 32

What did the Flixborough disaster of 1974 highlight?

  1. The value of dust control
  2. The danger of mercury
  3. The dangers of uncontrolled temporary modifications, leading to management of change requirements
  4. The need for more pipelines
Show answer & solution

Answer: (C) The dangers of uncontrolled temporary modifications, leading to management of change requirements

A temporary bypass pipe failed and released cyclohexane.

Question 33

What was the Ahmedpur East (Bahawalpur) tragedy of 2017 in Pakistan?

  1. An overturned oil tanker leaked fuel that ignited as people collected it, killing over 200
  2. A dam failure
  3. A chemical plant explosion
  4. A gas field blowout
Show answer & solution

Answer: (A) An overturned oil tanker leaked fuel that ignited as people collected it, killing over 200

It highlighted the danger of flammable liquid spills near crowds.

Question 34

What is the flash point classification used for flammable liquids?

  1. Grouping by price
  2. Grouping liquids by flash point to set storage and handling rules
  3. Grouping by viscosity
  4. Grouping by colour
Show answer & solution

Answer: (B) Grouping liquids by flash point to set storage and handling rules

Liquids with low flash points are most hazardous.

Question 35

What is a flash fire?

  1. A pool fire
  2. A BLEVE
  3. A jet fire
  4. Rapid burning of a flammable vapour cloud without significant overpressure
Show answer & solution

Answer: (D) Rapid burning of a flammable vapour cloud without significant overpressure

Burns occur to people inside the cloud.

Question 36

What is a deflagration?

  1. A combustion wave travelling slower than the speed of sound in the unburnt mixture
  2. A BLEVE
  3. A detonation
  4. A pool fire
Show answer & solution

Answer: (A) A combustion wave travelling slower than the speed of sound in the unburnt mixture

It can still create damaging overpressure in confined spaces.

Question 37

What is a detonation?

  1. A combustion wave travelling faster than the speed of sound, producing a shock wave
  2. A slow fire
  3. A flash fire
  4. A pool fire
Show answer & solution

Answer: (A) A combustion wave travelling faster than the speed of sound, producing a shock wave

Detonation pressures are much higher than deflagration pressures.

Question 38

What is an explosion vent (vent panel)?

  1. A valve for liquids
  2. A weak panel that opens at low pressure to relieve deflagration pressure safely
  3. A pressure gauge
  4. A flame arrester
Show answer & solution

Answer: (B) A weak panel that opens at low pressure to relieve deflagration pressure safely

It is used on dust collectors and silos.

Question 39

What is the minimum ignition energy (MIE)?

  1. The heat of combustion
  2. The autoignition temperature
  3. The flash point
  4. The smallest spark energy capable of igniting a flammable mixture
Show answer & solution

Answer: (D) The smallest spark energy capable of igniting a flammable mixture

Hydrogen's MIE is about 0.02 mJ.

Question 40

What is a layer of protection in process safety?

  1. A layer of paint
  2. A pipe coating
  3. An independent safeguard such as alarms, safety systems or relief valves that prevents or mitigates an incident
  4. A layer of insulation only
Show answer & solution

Answer: (C) An independent safeguard such as alarms, safety systems or relief valves that prevents or mitigates an incident

LOPA evaluates their adequacy.

Question 41

What is a reactive chemical hazard?

  1. A falling object
  2. A hazard from substances that react violently, decompose or polymerise under certain conditions
  3. A noise hazard
  4. A low-risk inert material
Show answer & solution

Answer: (B) A hazard from substances that react violently, decompose or polymerise under certain conditions

Thermal stability testing helps assess it.

Question 42

What is the lesson of the 2005 Texas City refinery explosion?

  1. The importance of process safety culture, proper siting of temporary buildings and avoiding overfilling of columns
  2. The danger of mercury
  3. The value of coal
  4. The need for more trucks
Show answer & solution

Answer: (A) The importance of process safety culture, proper siting of temporary buildings and avoiding overfilling of columns

A raffinate splitter overfilled during start-up.

Question 43

What is the main danger of LPG leaks in homes and plants?

  1. It rises and disperses quickly
  2. It is non-flammable
  3. It is toxic at low levels
  4. LPG vapour is heavier than air, collects in low areas and can explode when ignited
Show answer & solution

Answer: (D) LPG vapour is heavier than air, collects in low areas and can explode when ignited

Odorant helps detect leaks.

Practice these 43 questions interactively →