What is the main raw material for ammonia production in Pakistani fertiliser plants?
Show answer & solution
Answer: (D) Natural gas
Gas is both feedstock for hydrogen and fuel.
Chemical Engineering · Chemical Process Industries
35 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the main raw material for ammonia production in Pakistani fertiliser plants?
Answer: (D) Natural gas
Gas is both feedstock for hydrogen and fuel.
Which process is used for industrial ammonia synthesis?
Answer: (B) Haber–Bosch process
N₂ + 3H₂ ⇌ 2NH₃ over a promoted iron catalyst.
What are typical operating conditions for ammonia synthesis converters?
Answer: (C) About 150–250 bar and 400–500 °C
Pressure favours conversion and temperature gives an acceptable rate.
What is the typical single-pass conversion in an ammonia synthesis converter?
Answer: (B) About 15–25%
Unreacted gas is recycled after ammonia is condensed.
How is hydrogen for ammonia produced from natural gas?
Answer: (A) Steam reforming in a primary reformer followed by air addition in a secondary reformer
The secondary reformer also supplies the nitrogen.
Why is air added in the secondary reformer of an ammonia plant?
Answer: (D) To supply nitrogen for synthesis and heat from partial combustion
The H₂:N₂ ratio is adjusted to about 3:1.
Why must sulphur be removed from natural gas before steam reforming?
Answer: (C) It poisons the nickel reforming catalyst
Hydrodesulphurisation and zinc oxide beds are used.
What is the purpose of the methanator in an ammonia plant?
Answer: (A) To convert residual CO and CO₂ to methane, since they poison the synthesis catalyst
Methane is inert in the synthesis loop.
Why is a purge stream taken from the ammonia synthesis loop?
Answer: (A) To prevent build-up of inert gases such as argon and methane
Hydrogen is recovered from purge gas.
What are the raw materials for urea production?
Answer: (B) Ammonia and carbon dioxide
CO₂ comes from the ammonia plant's CO₂ removal unit.
What is the intermediate formed in urea synthesis?
Answer: (C) Ammonium carbamate
2NH₃ + CO₂ → NH₂COONH₄, which dehydrates to urea.
Which step in urea synthesis is endothermic?
Answer: (D) Dehydration of ammonium carbamate to urea
Carbamate formation is fast and exothermic.
What is the nitrogen content of urea?
Answer: (C) About 46%
Urea has the highest nitrogen content of solid fertilisers.
What is biuret in urea fertiliser?
Answer: (B) An impurity formed by heating urea, harmful to some crops
Its content is limited to about 1%.
What is prilling in urea production?
Answer: (A) Spraying molten urea from the top of a tall tower so that droplets solidify as they fall
Granulation gives larger, stronger particles.
Which urea process licensors are widely used?
Answer: (D) Stamicarbon (CO₂ stripping) and Saipem Snamprogetti (ammonia stripping)
Both recycle unconverted carbamate.
What is the main raw material for phosphatic fertilisers?
Answer: (D) Phosphate rock
Phosphate rock is mined in Hazara (near Abbottabad) in Pakistan.
How is phosphoric acid made by the wet process?
Answer: (C) By reacting phosphate rock with sulphuric acid, producing gypsum by-product
Phosphogypsum disposal is an environmental issue.
What is DAP?
Answer: (A) Diammonium phosphate, (NH₄)₂HPO₄, containing 18% N and 46% P₂O₅
It is made by reacting ammonia with phosphoric acid.
What is the nutrient grade of DAP?
Answer: (C) 18-46-0
Grades give N, P₂O₅ and K₂O percentages.
What is single superphosphate (SSP)?
Answer: (B) A fertiliser made by reacting phosphate rock with sulphuric acid, with about 16–20% P₂O₅
Triple superphosphate uses phosphoric acid and has about 46% P₂O₅.
Which process produces nitric acid from ammonia?
Answer: (A) Ostwald process
Ammonia is oxidised over platinum–rhodium gauze.
What is calcium ammonium nitrate (CAN)?
Answer: (D) A mixture of ammonium nitrate with calcium carbonate or dolomite, containing about 26% N
Limestone dilution makes it safer than pure ammonium nitrate.
Why is ammonium nitrate a safety concern?
Answer: (B) It can decompose explosively when contaminated, confined or heated
Strict storage rules apply.
What is the nutrient form of potassium expressed as in fertiliser grades?
Answer: (A) K₂O
Muriate of potash (KCl) has about 60% K₂O.
What is NPK fertiliser?
Answer: (B) A compound fertiliser supplying nitrogen, phosphorus and potassium
Grades are given as N-P₂O₅-K₂O percentages.
What is the purpose of the CO₂ removal section in an ammonia plant?
Answer: (C) To remove CO₂ from synthesis gas and supply it for urea production
Activated MDEA or Benfield solutions are used.
What is the approximate natural gas consumption basis used to compare ammonia plant efficiency?
Answer: (D) Gigajoules of gas per tonne of ammonia, about 28–35 GJ/t for modern plants
Older plants consume more energy.
What is ammonium sulphate's nitrogen content?
Answer: (A) About 21%
It also supplies sulphur.
What is the main use of anhydrous ammonia besides fertiliser production?
Answer: (C) Refrigeration and manufacture of nitric acid and chemicals
It is stored as a liquid under pressure or refrigerated.
What is the theoretical amount of ammonia needed to produce 1 tonne of urea?
Answer: (B) About 0.57 tonne
2 × 17/60 = 0.567.
What is the theoretical amount of CO₂ needed to produce 1 tonne of urea?
Answer: (C) About 0.73 tonne
44/60 = 0.733.
What is the high-temperature shift converter catalyst in ammonia plants?
Answer: (D) Iron oxide–chromium oxide
It converts most of the CO to CO₂ and H₂.
Why are urea granules often preferred to prills?
Answer: (A) They are larger and stronger, with less dust and caking
Fluid-bed granulators are widely used.
What is nitrophosphate fertiliser?
Answer: (D) A fertiliser made by digesting phosphate rock with nitric acid
Pak-Arab Fertilizers at Multan produced nitrophos.