What are the main raw materials for Portland cement?
Show answer & solution
Answer: (A) Limestone and clay or shale
They supply CaO, SiO₂, Al₂O₃ and Fe₂O₃.
Chemical Engineering · Chemical Process Industries
36 questions, each with the answer and a worked solution.
Practice interactively and track your score →What are the main raw materials for Portland cement?
Answer: (A) Limestone and clay or shale
They supply CaO, SiO₂, Al₂O₃ and Fe₂O₃.
What is clinker?
Answer: (D) Nodules produced by burning raw meal in a kiln at about 1,450 °C
Clinker is ground with gypsum to make cement.
Why is gypsum added to cement clinker during grinding?
Answer: (C) To control (retard) the setting time of cement
About 3–5% gypsum is added.
Which kiln process is used in modern cement plants?
Answer: (A) Dry process with preheater and precalciner
The dry process uses much less fuel.
What is the role of the precalciner in a cement plant?
Answer: (B) To decompose most of the limestone before the kiln, using part of the fuel
It increases kiln capacity.
What are the four main clinker compounds?
Answer: (C) Tricalcium silicate, dicalcium silicate, tricalcium aluminate and tetracalcium aluminoferrite
They are written C₃S, C₂S, C₃A and C₄AF.
Which clinker compound is mainly responsible for early strength of cement?
Answer: (D) Tricalcium silicate (C₃S)
C₂S contributes to later strength.
Which clinker compound reacts fastest with water and must be controlled by gypsum?
Answer: (A) Tricalcium aluminate (C₃A)
It causes flash setting without gypsum.
What is sulphate-resisting cement?
Answer: (B) Cement with low C₃A content to resist sulphate attack
It is used in saline soils and sewage works.
What is the main fuel used in Pakistani cement kilns?
Answer: (C) Coal, increasingly supplemented with alternative fuels
Imported and local coal are both used.
What is the purpose of the clinker cooler?
Answer: (A) To cool hot clinker and recover heat for combustion air
Grate coolers are common.
What is the main source of CO₂ emissions in cement production?
Answer: (B) Calcination of limestone and fuel combustion
About 60% comes from calcination.
What are blended cements?
Answer: (D) Cements where part of the clinker is replaced by fly ash, slag or limestone
They reduce CO₂ and cost.
What are the main raw materials for soda-lime glass?
Answer: (C) Silica sand, soda ash and limestone
Cullet (recycled glass) reduces energy use.
What is the role of soda ash in glass making?
Answer: (D) It acts as a flux to lower the melting temperature of silica
Lime stabilises the glass against water.
Which furnace type is used for continuous large-scale glass melting?
Answer: (A) Regenerative tank furnace
Regenerators recover heat from flue gases.
What is annealing of glass?
Answer: (B) Controlled slow cooling to relieve internal stresses
It is done in a lehr.
What is the float glass process?
Answer: (B) Floating molten glass on a bath of molten tin to produce flat sheet glass
It gives smooth, parallel surfaces.
Which oxide is added to make borosilicate glass resistant to thermal shock?
Answer: (D) Boron oxide (B₂O₃)
It has a low thermal expansion coefficient.
What are the main raw materials for ceramics such as tiles and sanitary ware?
Answer: (A) Clay, feldspar and silica
Feldspar acts as a flux.
What is vitrification in ceramics?
Answer: (C) Formation of a glassy phase during firing that bonds particles and reduces porosity
Higher firing increases vitrification.
Which refractory is used in the burning zone of cement kilns?
Answer: (B) Magnesia-based (magnesia-spinel) bricks
They resist the basic clinker coating.
What is lime (quicklime) produced from?
Answer: (D) Calcination of limestone at about 900–1,000 °C
CaCO₃ → CaO + CO₂.
What is slaked lime?
Answer: (C) Calcium hydroxide formed by adding water to quicklime
The reaction is strongly exothermic.
What is plaster of Paris made from?
Answer: (A) Heating gypsum to form calcium sulphate hemihydrate
It sets by rehydrating to gypsum.
What are the main grinding systems in modern cement plants?
Answer: (A) Ball mills and vertical roller mills
Vertical roller mills use less energy.
What is the lime saturation factor (LSF) in cement raw mix?
Answer: (D) A ratio comparing CaO with the amount that can combine with silica, alumina and iron
Typical LSF values are about 0.92–0.98.
What is the silica modulus of cement raw mix?
Answer: (B) SiO₂/(Al₂O₃ + Fe₂O₃)
It affects burnability and liquid phase.
What is the typical specific heat consumption of a modern dry-process cement kiln?
Answer: (C) About 3,000–3,400 kJ per kg of clinker
Wet process kilns use far more.
What is the purpose of the bypass system in some cement kilns?
Answer: (A) To remove part of the kiln gas rich in alkalis and chlorides that cause build-ups
Alkali, chloride and sulphur cycles cause blockages.
What is ordinary Portland cement's typical fineness measured as Blaine specific surface?
Answer: (C) About 300–400 m²/kg
Finer cement gains strength faster.
What makes coloured glass such as green or amber?
Answer: (B) Small amounts of metal oxides such as iron, chromium or sulphides
Iron gives green tint.
Which glass is used for optical and decorative crystal because of its high refractive index?
Answer: (D) Lead glass
Lead oxide increases density and brilliance.
What is cullet?
Answer: (A) Broken or recycled glass added to the batch
It melts more easily and saves energy.
What is the role of a lehr in glass manufacture?
Answer: (B) An annealing oven for controlled cooling
It removes internal stresses.
What is the main use of fly ash in the cement industry?
Answer: (B) As a pozzolanic material replacing part of the clinker
It comes from coal-fired power plants.