Which three elements make up the fire triangle?
Show answer & solution
Answer: (D) Fuel, heat and oxygen
Removing any one element puts out a fire.
Mining Engineering · Mine Safety, Rescue & Legislation
38 questions, each with the answer and a worked solution.
Practice interactively and track your score →Which three elements make up the fire triangle?
Answer: (D) Fuel, heat and oxygen
Removing any one element puts out a fire.
What is spontaneous combustion of coal?
Answer: (B) Self-heating of coal by slow oxidation until it ignites without an external flame
Heat from oxidation builds up where it cannot escape.
Which factor increases the risk of spontaneous combustion in coal?
Answer: (C) Crushed coal with a slow leakage of air through it
A slow air supply brings oxygen but does not remove the heat.
Which mineral in coal is believed to promote spontaneous heating?
Answer: (A) Pyrite
Pyrite oxidation is exothermic and breaks up the coal.
What is the incubation period in spontaneous combustion?
Answer: (C) The time between exposure of coal to air and the start of active fire
Rapid extraction and good sealing keep mining ahead of the incubation period.
Which gas is the earliest common indicator of a spontaneous heating?
Answer: (B) Carbon monoxide
Small rises in CO in return air signal developing heating.
What does Graham's ratio indicate?
Answer: (A) The intensity of a heating, from CO produced compared with oxygen consumed
Rising values of Graham's ratio show a growing heating.
What are the main methods of fighting an underground mine fire?
Answer: (D) Direct attack with water or extinguishers, sealing, inertisation and flooding
The method depends on fire size, access and gas conditions.
What is the purpose of sealing a fire area?
Answer: (B) To cut off oxygen so the fire dies out
Seals isolate the fire area from the ventilation system.
Why must seals near gassy fire areas be built strong enough to resist explosions?
Answer: (A) Methane may build up behind the seal into the explosive range
Explosion-resistant seals protect rescuers during and after sealing.
What is inertisation of a sealed fire area?
Answer: (C) Injecting inert gas such as nitrogen or carbon dioxide to make the atmosphere non-explosive
Inert gas speeds extinction and reduces explosion risk.
Why must a sealed fire area be reopened with great care?
Answer: (D) Fresh air reaching hot material can cause re-ignition or an explosion
Atmosphere sampling must show the fire is extinct before reopening.
Which type of extinguisher should be used on fires in live electrical equipment?
Answer: (B) Carbon dioxide or dry powder
Water conducts electricity and endangers the user.
What is the most common use of water in fighting underground fires?
Answer: (D) Cooling and extinguishing burning coal, timber and belts
Fire mains and hoses are installed along conveyor roadways.
Which of these is a major cause of underground fires?
Answer: (C) Conveyor belt friction and overheated machinery
Belt slip, seized rollers and hot bearings ignite belts and coal dust.
Why are only flameproof or intrinsically safe electrical apparatus allowed in gassy areas of coal mines?
Answer: (A) To prevent electrical sparks igniting methane
Flameproof enclosures contain any internal explosion.
What is an intrinsically safe electrical circuit?
Answer: (D) A circuit whose energy is too low to ignite a flammable gas mixture
Intrinsic safety is used for signalling and instruments.
Which of these can cause frictional ignition of methane?
Answer: (A) Cutting picks striking quartz-rich sandstone
Hot streaks from frictional sparks can ignite gas at the cutting head.
How is frictional ignition at coal cutting machines commonly reduced?
Answer: (C) Water sprays directed behind the cutting picks and sharp picks
Sprays cool the hot streak and dilute gas.
Why are miners searched for smoking materials before going underground in gassy mines?
Answer: (B) Matches and lighters can ignite methane
Contraband search is required in safety lamp mines.
What is the most important single measure to prevent methane explosions?
Answer: (A) Adequate ventilation to keep methane well below its lower explosive limit
Ventilation dilutes and removes methane.
What usually happens when a methane explosion occurs in a dusty coal mine?
Answer: (B) It raises coal dust and may trigger a much larger coal dust explosion
Stone dusting prevents the dust explosion from spreading.
Which coal mine in Balochistan suffered a major methane explosion in March 2011 that killed over forty miners?
Answer: (C) Sanjdi
The Sanjdi disaster near Quetta was one of Pakistan's worst coal mining accidents.
What is a fire stopping?
Answer: (D) A temporary or permanent seal built to isolate a fire area
Temporary stoppings are built quickly, then replaced by permanent seals.
Why is it dangerous to reverse ventilation during a fire without a plan?
Answer: (C) It may drive smoke and gas over workers or bring flammable gas onto the fire
Reversal decisions follow the mine's emergency plan.
What is the main danger from fires in underground mines besides burns?
Answer: (B) Toxic smoke and carbon monoxide spreading through airways
Most deaths in mine fires are from smoke and CO.
Why are fire-resistant hydraulic fluids used in underground machines?
Answer: (D) To reduce the risk of fire from leaks onto hot surfaces
Mineral oil leaks can ignite on hot surfaces.
What is the purpose of fire drills in underground mines?
Answer: (A) To train workers to escape quickly and use self-rescuers and escapeways
Regular drills save lives in emergencies.
Why is coal dust allowed to accumulate along conveyor roadways a fire and explosion hazard?
Answer: (A) Dust can be ignited by hot rollers or a methane explosion and spread fire
Regular cleaning and stone dusting are required.
Which gas analysis ratio helps judge whether an atmosphere in a sealed area is explosive?
Answer: (B) Comparing measured methane, oxygen and inert gas on a Coward's diagram
The diagram shows whether the mixture can explode now or if air is added.
What is an open fire in mining terms?
Answer: (C) A fire with visible flame
Open fires spread quickly along airways.
Why must welding or cutting underground in coal mines be done only under strict permit?
Answer: (D) Hot work can ignite methane, coal dust, belts or timber
Gas tests, fire watch and extinguishers are required.
What should workers do when they discover a fire underground that they cannot safely put out?
Answer: (A) Raise the alarm, warn others and withdraw by the planned escape route
Early warning and orderly withdrawal save lives.
Which of these is a common source of ignition of methane in older mines?
Answer: (C) Faulty or misused flame safety lamps and shotfiring
Modern cap lamps are electric and sealed.
What is a heating in mining terms?
Answer: (D) An area of coal undergoing spontaneous self-heating
Heatings are detected early by CO and temperature monitoring.
What is the main advantage of sealing a fire as close to it as possible?
Answer: (B) A smaller sealed volume reduces oxygen faster and limits gas accumulation
Seal location depends on safety and access.
Why is nitrogen injection used in sealed goaf areas of coal mines?
Answer: (A) To keep oxygen low and prevent spontaneous combustion and explosions
Nitrogen is inert and can be generated on site.
What is the main purpose of a fire main along conveyor roadways?
Answer: (D) To supply water for fighting fires quickly
Hydrants and hoses are placed at intervals.