Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Mine Safety, Rescue & Legislation: Inundation and Water Hazards

Mining Engineering · Mine Safety, Rescue & Legislation

34 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is inundation in mining?

  1. Pumping water out of a mine
  2. Sudden inflow of water, slurry or mud into mine workings
  3. Rain falling on the surface
  4. Water sprays for dust
Show answer & solution

Answer: (B) Sudden inflow of water, slurry or mud into mine workings

Inundations have caused many mining disasters.

Question 2

Which is the most common source of dangerous inrushes in coal mines?

  1. Waterlogged old workings
  2. Fresh intake air
  3. Ventilation ducts
  4. Stone dust barriers
Show answer & solution

Answer: (A) Waterlogged old workings

Old workings may contain large bodies of water under pressure.

Question 3

Why must an adequate barrier of solid coal or rock be left against waterlogged old workings?

  1. To improve ventilation
  2. To prevent water breaking through into active workings
  3. To support the fan
  4. To store explosives
Show answer & solution

Answer: (B) To prevent water breaking through into active workings

Barrier width depends on water pressure and rock strength.

Question 4

What is the purpose of advance boreholes when approaching old waterlogged workings?

  1. To measure ventilation
  2. To drain the surface
  3. To blast the face
  4. To detect water ahead of the face before it breaks through
Show answer & solution

Answer: (D) To detect water ahead of the face before it breaks through

Boreholes are kept well ahead and to the flanks of the heading.

Question 5

Which surface water source can cause inundation of shallow mines?

  1. Fresh air
  2. Stone dust
  3. Rivers, lakes and flood water entering through openings or cracks
  4. Electric cables
Show answer & solution

Answer: (C) Rivers, lakes and flood water entering through openings or cracks

Shaft collars and adits should be above flood level.

Question 6

How can geological faults contribute to mine inundation?

  1. They can act as channels connecting workings to aquifers or water bodies
  2. They have no effect
  3. They make rock dry
  4. They always stop water
Show answer & solution

Answer: (A) They can act as channels connecting workings to aquifers or water bodies

Faults must be approached with care and probing.

Question 7

What is an underground water dam (bulkhead) used for?

  1. To divert air
  2. To hold back water from abandoned or flooded areas
  3. To support the roof
  4. To store explosives
Show answer & solution

Answer: (B) To hold back water from abandoned or flooded areas

Dams are designed for the full water pressure behind them.

Question 8

Which type of pump is most commonly used for main underground dewatering?

  1. Reciprocating air compressor
  2. Hand pump
  3. Multistage centrifugal pump
  4. Bucket and rope
Show answer & solution

Answer: (C) Multistage centrifugal pump

Multistage pumps develop the high head needed in deep mines.

Question 9

What is the purpose of a main sump underground?

  1. To store explosives
  2. To hoist coal
  3. To ventilate the mine
  4. To collect water and provide storage before it is pumped out
Show answer & solution

Answer: (D) To collect water and provide storage before it is pumped out

Sump capacity allows time to deal with pump failures.

Question 10

Why should mine plans accurately show all old workings?

  1. So that water and gas hazards can be anticipated and avoided
  2. To show rainfall
  3. To show the fan
  4. To show wages
Show answer & solution

Answer: (A) So that water and gas hazards can be anticipated and avoided

Inaccurate plans of old workings caused many inrushes.

Question 11

What should workers do when signs of an inrush, such as unusual water seepage or roof sweating, appear?

  1. Ignore the signs
  2. Stop work, withdraw and report immediately
  3. Blast the face
  4. Continue mining faster
Show answer & solution

Answer: (B) Stop work, withdraw and report immediately

Warning signs include increased seepage, noises and bleeding of the face.

Question 12

What does "bleeding" or sweating of the coal face indicate?

  1. Strong roof
  2. A fire
  3. Methane only
  4. Water under pressure close to the face
Show answer & solution

Answer: (D) Water under pressure close to the face

It is a warning sign of nearby waterlogged workings.

Question 13

Why are shafts and inclines often lined and sealed through water-bearing strata?

  1. To reduce noise
  2. To increase ventilation
  3. To prevent water entering the mine from aquifers
  4. To support hoisting ropes
Show answer & solution

Answer: (C) To prevent water entering the mine from aquifers

Tubbing or concrete linings seal aquifers.

Question 14

What is dewatering in surface and underground mining?

  1. Filling old workings with water
  2. Adding water to the mine
  3. Spraying water on roads
  4. Lowering the groundwater level by pumping from wells or sumps
Show answer & solution

Answer: (D) Lowering the groundwater level by pumping from wells or sumps

Dewatering improves slope stability and working conditions.

Question 15

What is the danger of mud rushes in mines?

  1. They improve stability
  2. They provide drinking water
  3. Sudden flows of wet fine material can bury workers and equipment
  4. They cool the mine
Show answer & solution

Answer: (C) Sudden flows of wet fine material can bury workers and equipment

Mud rushes occur in caving mines and near saturated fill.

Question 16

Why must water from mines often be treated before discharge?

  1. It may be acidic, contain suspended solids or dissolved metals
  2. It is too cold
  3. It contains no minerals
  4. It is always pure
Show answer & solution

Answer: (A) It may be acidic, contain suspended solids or dissolved metals

Treatment protects rivers and groundwater.

Question 17

What is a pressure-relief or drainage borehole into old workings used for?

  1. Measuring rock strength
  2. Draining water in a controlled way before mining nearby
  3. Storing explosives
  4. Injecting methane
Show answer & solution

Answer: (B) Draining water in a controlled way before mining nearby

Controlled drainage reduces the risk of a sudden inrush.

Question 18

What is the main purpose of monitoring water levels and inflows in a mine?

  1. To check fan speed
  2. To calculate wages
  3. To detect changes that may signal an inrush or pump problem
  4. To measure ore grade
Show answer & solution

Answer: (C) To detect changes that may signal an inrush or pump problem

Unexpected increases in inflow need investigation.

Question 19

Why must electrical pumps in a mine have standby units?

  1. To double the noise
  2. To heat the water
  3. To reduce power
  4. To keep pumping if one pump fails
Show answer & solution

Answer: (D) To keep pumping if one pump fails

Pump failure can quickly flood lower workings.

Question 20

Which precaution protects shaft tops and adit mouths from surface flooding?

  1. Siting them above the highest flood level and building embankments
  2. Placing them in river beds
  3. Leaving them unfenced
  4. Removing drainage channels
Show answer & solution

Answer: (A) Siting them above the highest flood level and building embankments

Many inundations started from flood water entering mine openings.

Question 21

What is meant by water-logged workings?

  1. Workings with high humidity only
  2. Old workings filled with accumulated water
  3. Workings with drinking water taps
  4. Workings with water sprays
Show answer & solution

Answer: (B) Old workings filled with accumulated water

Waterlogged workings are a major hazard to adjacent mines.

Question 22

What is a probe-hole drilling programme?

  1. A blasting pattern
  2. A drainage ditch plan
  3. Systematic drilling ahead of headings to detect water, gas or old workings
  4. A ventilation survey
Show answer & solution

Answer: (C) Systematic drilling ahead of headings to detect water, gas or old workings

Probe holes are drilled before advancing in risk zones.

Question 23

Why is rescue from inundated mines especially difficult?

  1. Water may trap workers in pockets of air and access may be blocked
  2. Inundations are always small
  3. Rescuers do not need equipment
  4. Water makes air fresher
Show answer & solution

Answer: (A) Water may trap workers in pockets of air and access may be blocked

Pumping and drilling may be needed to reach trapped miners.

Question 24

What is the main hazard when mining under the sea, rivers or lakes?

  1. Excess dryness
  2. Inrush of water through fractures above the workings
  3. Lack of methane
  4. Too much oxygen
Show answer & solution

Answer: (B) Inrush of water through fractures above the workings

A safe thickness of cover must be left.

Question 25

What is the main purpose of a mine drainage plan?

  1. To show fans only
  2. To show blast holes
  3. To show the sumps, pumps, pipelines and drainage routes in the mine
  4. To show wages
Show answer & solution

Answer: (C) To show the sumps, pumps, pipelines and drainage routes in the mine

Drainage plans are needed for emergency planning and pump maintenance.

Question 26

Why should pump capacity be greater than the normal water inflow?

  1. To waste power
  2. To dry the coal
  3. To handle sudden increases in inflow and pump breakdowns
  4. To reduce sump size
Show answer & solution

Answer: (C) To handle sudden increases in inflow and pump breakdowns

Spare capacity protects lower workings from flooding.

Question 27

Why must electrical switchgear for pumps be located above possible flood levels?

  1. To reduce noise
  2. So that pumps can keep working as water rises
  3. To save cable
  4. To keep it warm
Show answer & solution

Answer: (B) So that pumps can keep working as water rises

Flooded switchgear stops pumping when it is most needed.

Question 28

What is the main hazard of driving towards an unmapped abandoned mine?

  1. Sudden holing into water, gas or collapsed ground
  2. Excess ventilation
  3. Higher coal quality
  4. Too much light
Show answer & solution

Answer: (A) Sudden holing into water, gas or collapsed ground

Many inundations happened when workings broke into unmapped old workings.

Question 29

What does a sudden fall in water flow from a borehole drilled into old workings indicate?

  1. The fan has stopped
  2. There is no danger
  3. There is a fire
  4. The water may be draining a limited body, or the hole may be blocked
Show answer & solution

Answer: (D) The water may be draining a limited body, or the hole may be blocked

Flow and pressure from probe holes are monitored and interpreted carefully.

Question 30

Which type of rock above a mine is most dangerous for water inflow?

  1. Solid salt
  2. Massive impermeable clay
  3. Dry granite
  4. Highly permeable sandstone or limestone aquifers
Show answer & solution

Answer: (D) Highly permeable sandstone or limestone aquifers

Permeable strata can deliver large inflows through fractures.

Question 31

What is a safety pillar against water in mining?

  1. A pillar supporting the fan
  2. A pillar of solid mineral left to prevent water breaking into the workings
  3. A pillar in the shaft
  4. A pillar for storing explosives
Show answer & solution

Answer: (B) A pillar of solid mineral left to prevent water breaking into the workings

Safety pillars protect against rivers, lakes and waterlogged workings.

Question 32

Why should old shafts on the surface be capped and their positions recorded?

  1. To prevent surface water entering and people falling in
  2. To mark the boundary
  3. To improve ventilation
  4. To store coal
Show answer & solution

Answer: (A) To prevent surface water entering and people falling in

Old shafts are a danger both to the public and to nearby mines.

Question 33

What is the main purpose of an emergency flood alarm in a mine?

  1. To start pumps only
  2. To call shift change
  3. To warn workers to escape to higher ground or the surface
  4. To stop conveyors
Show answer & solution

Answer: (C) To warn workers to escape to higher ground or the surface

Early warning gives workers time to escape.

Question 34

Which escape direction is safest for workers when a mine begins to flood?

  1. Towards the lowest workings
  2. Into old workings
  3. Towards higher workings and the outlets
  4. Into the sump
Show answer & solution

Answer: (C) Towards higher workings and the outlets

Water flows to the lowest parts of the mine first.

Practice these 34 questions interactively →