What is a pure substance?
Show answer & solution
Answer: (A) A substance with a uniform and fixed chemical composition throughout
Water in its solid, liquid and vapour phases is a pure substance.
Mechanical Engineering · Thermodynamics
33 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is a pure substance?
Answer: (A) A substance with a uniform and fixed chemical composition throughout
Water in its solid, liquid and vapour phases is a pure substance.
What is the saturation temperature?
Answer: (C) The temperature at which a liquid boils at a given pressure
At 1.013 bar, the saturation temperature of water is 100 °C.
How does the boiling point of water change as pressure increases?
Answer: (B) It increases
Pressure cookers use this effect to cook food faster.
What is latent heat?
Answer: (D) Heat absorbed or released during a change of phase at constant temperature
The latent heat of vaporisation of water at 1 atm is about 2257 kJ/kg.
What is wet steam?
Answer: (A) Steam containing water particles in suspension
It is produced when vaporisation is incomplete.
What is dry saturated steam?
Answer: (B) Steam at saturation temperature that contains no water particles
It is the boundary between wet and superheated steam.
What is superheated steam?
Answer: (D) Steam heated to a temperature above its saturation temperature at the given pressure
The difference above saturation temperature is called the degree of superheat.
What is the dryness fraction of steam?
Answer: (C) The ratio of the mass of dry steam to the total mass of the wet steam
Dry saturated steam has a dryness fraction of 1.
Which instrument is used to measure the dryness fraction of steam?
Answer: (D) Throttling or separating-and-throttling calorimeter
A throttling calorimeter works when the steam becomes superheated after throttling.
What is the critical point of water?
Answer: (C) The state at which the saturated liquid and saturated vapour states become identical
For water it is about 374 °C and 221 bar.
What is the latent heat of vaporisation at the critical point?
Answer: (A) Zero
Liquid changes directly to vapour without a distinct phase change.
What is the triple point of water?
Answer: (B) The state where solid, liquid and vapour phases exist together in equilibrium
It occurs at 0.01 °C and about 0.006 bar (611 Pa).
Which chart is commonly used for steam calculations, plotting enthalpy against entropy?
Answer: (C) Mollier diagram (h–s chart)
It was developed by Richard Mollier.
How does the enthalpy of wet steam depend on dryness fraction x?
Answer: (A) h = hf + x hfg
hf is liquid enthalpy and hfg is latent heat.
What is the specific volume of wet steam with dryness fraction x, approximately?
Answer: (B) x × vg
The volume of the water part is usually neglected.
What is a steam table?
Answer: (D) A table giving properties of water and steam at different pressures and temperatures
It gives saturation temperature, enthalpy, entropy and specific volume.
On which cycle do steam (thermal) power plants work?
Answer: (C) Rankine cycle
Coal-fired plants such as the Sahiwal coal power plant in Pakistan use steam Rankine cycles.
What are the four main processes of the ideal Rankine cycle?
Answer: (A) Pump compression, constant-pressure heating in the boiler, isentropic expansion in the turbine and constant-pressure condensation
It is the basic cycle of steam power plants.
What is the main thermodynamic difference between the Rankine cycle and the Carnot cycle?
Answer: (D) In the Rankine cycle, heat is supplied to water at temperatures below the maximum cycle temperature
Heat is added over a range of temperatures, which lowers the mean temperature of heat addition.
Why is the Carnot cycle not used in practice for steam power plants?
Answer: (B) Compressing wet steam is impractical and causes damage and high work input
The Rankine cycle condenses steam fully and uses a pump instead.
How does superheating the steam affect the Rankine cycle?
Answer: (B) It increases efficiency and reduces moisture at the turbine exit
Wet steam erodes turbine blades.
What is the purpose of reheating in a Rankine cycle?
Answer: (A) To reduce moisture in the low-pressure turbine stages and increase work output
Steam is reheated after partial expansion in the turbine.
What is regenerative feed-water heating in a Rankine cycle?
Answer: (C) Using steam bled from the turbine to preheat the boiler feed water
It raises the mean temperature of heat addition and improves efficiency.
How does lowering the condenser pressure affect the Rankine cycle?
Answer: (D) It increases efficiency
It lowers the temperature at which heat is rejected.
Why is the pump work in a Rankine cycle very small compared with turbine work?
Answer: (A) Liquid water has a very small specific volume
Pump work ≈ v(p₂ − p₁), and v is small for liquids.
What is the work ratio of a cycle?
Answer: (D) The ratio of net work to gross (turbine) work
A high work ratio indicates a cycle less sensitive to component inefficiencies.
What is a binary vapour cycle?
Answer: (B) A cycle using two working fluids, such as mercury and steam, to improve efficiency
The high-temperature fluid's condenser acts as the boiler for the second fluid.
What is the degree of superheat?
Answer: (B) The difference between the actual temperature of superheated steam and its saturation temperature at the same pressure
A higher degree of superheat makes steam behave more like an ideal gas.
What is the enthalpy of dry saturated steam made up of?
Answer: (D) Sensible heat of the liquid plus latent heat of vaporisation (hg = hf + hfg)
For wet steam, only a fraction x of the latent heat is added.
How does the latent heat of vaporisation of water change as pressure increases?
Answer: (C) It decreases and becomes zero at the critical pressure
At higher pressures, less heat is needed to change liquid to vapour.
What is a separating calorimeter used for?
Answer: (A) Removing water particles mechanically to find the dryness fraction of very wet steam
It is often combined with a throttling calorimeter.
What is the specific volume of saturated water vapour compared with saturated liquid water at 1 atm?
Answer: (C) It is about 1600 times larger
vg ≈ 1.673 m³/kg and vf ≈ 0.001 m³/kg at 100 °C.
On a T–s diagram, what does the area enclosed by a Rankine cycle represent?
Answer: (A) Net work output (net heat supplied)
The same is true for any cycle on a T–s diagram.