What is friction?
Show answer & solution
Answer: (D) The force that opposes relative motion between two surfaces in contact
It acts along the surfaces of contact.
Mechanical Engineering · Engineering Mechanics
36 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is friction?
Answer: (D) The force that opposes relative motion between two surfaces in contact
It acts along the surfaces of contact.
What is limiting friction?
Answer: (A) The maximum friction force acting when a body is just about to slide
It equals μ times the normal reaction.
What is the coefficient of friction?
Answer: (B) The ratio of limiting friction to normal reaction
μ = F/R.
What does the coefficient of friction depend on?
Answer: (D) The nature of the surfaces in contact
It is nearly independent of contact area.
What is dynamic (kinetic) friction?
Answer: (C) The friction acting after a body has started moving
It is slightly less than limiting friction.
How does dynamic friction compare with static (limiting) friction?
Answer: (B) It is less
It is harder to start a body moving than to keep it moving.
Which statement about the laws of dry friction is incorrect?
Answer: (A) Friction is proportional to the sliding velocity
Kinetic friction is nearly independent of velocity at moderate speeds.
What is rolling friction?
Answer: (D) The resistance when a body rolls over a surface
It is much smaller than sliding friction.
What is the angle of friction?
Answer: (C) The angle between the normal reaction and the resultant of the normal reaction and limiting friction
tan φ = μ.
What is the tangent of the angle of friction equal to?
Answer: (A) The coefficient of friction
μ = tan φ.
What is the angle of repose?
Answer: (B) The angle of an inclined plane at which a body placed on it is just about to slide down
It is equal to the angle of friction.
Which statement about the angle of repose is not correct?
Answer: (B) Its sine equals the coefficient of friction
tan of the angle of repose equals μ.
What is the acceleration of a body sliding down a smooth inclined plane of angle α?
Answer: (C) g sin α
There is no friction to oppose the component of weight along the plane.
What force parallel to a rough inclined plane is needed to just move a body of weight W up the plane?
Answer: (D) W(sin α + μ cos α)
Friction acts down the plane when the body moves up.
At what angle to an inclined plane should a force be applied to drag a body up the plane with the least effort?
Answer: (A) At an angle equal to the angle of friction
The least effort is W sin(α + φ).
What horizontal force is needed to just move a body of weight W up a rough plane inclined at α, with friction angle φ?
Answer: (C) W tan(α + φ)
This is the same as the effort in a screw jack.
What is the effort needed to lift a load W with a screw jack having helix angle α and friction angle φ (at the mean radius)?
Answer: (B) W tan(α + φ)
Lowering the load needs W tan(φ − α).
What is the efficiency of a screw jack?
Answer: (D) tan α / tan(α + φ)
Efficiency is maximum when α = 45° − φ/2.
When is a screw jack self-locking?
Answer: (A) When the friction angle is greater than the helix angle
The load then stays up without effort.
What is the ratio of belt tensions on the tight and slack sides for a flat belt on a pulley?
Answer: (D) e^(μθ)
θ is the angle of lap in radians.
Why is it easier to pull a lawn roller than to push it?
Answer: (B) Pulling reduces the normal reaction, and therefore friction, while pushing increases it
The vertical component of force changes the normal reaction.
A block of weight 100 N rests on a horizontal surface with μ = 0.3. What horizontal force is needed to just move it?
Answer: (B) 30 N
F = μW = 0.3 × 100.
When a body is about to slide on a horizontal surface under a horizontal force, how is the force related to friction?
Answer: (A) The applied force equals the limiting friction
At impending motion, F = μR.
What is a wedge used for?
Answer: (C) Lifting heavy loads or tightening parts with small effort using friction and an inclined surface
Its efficiency depends on wedge angle and friction.
What is the minimum value of coefficient of friction needed for a ladder to stand against a smooth wall at a given angle?
Answer: (D) It depends on the angle of the ladder; a steeper ladder needs less friction
μ ≥ cot θ ÷ 2 for a uniform ladder at angle θ to the ground.
A body of weight 200 N is placed on a plane inclined at 30°. If μ = 0.2, will it slide down without any applied force?
Answer: (A) Yes, because tan 30° (0.577) is greater than μ
A body slides if the incline angle exceeds the angle of repose.
Why does friction act downwards on a body moving up an inclined plane?
Answer: (A) Friction always opposes the direction of motion
When moving down, friction acts up the plane.
What is the effort needed to move a body of weight W down a rough inclined plane at angle α by a force parallel to the plane, when α is less than the angle of friction?
Answer: (B) W(μ cos α − sin α)
If α exceeds the angle of friction, the body slides on its own.
Which type of friction exists between lubricated surfaces separated by a thick fluid film?
Answer: (D) Fluid (viscous) friction
It depends on the viscosity of the fluid.
What is Coulomb friction?
Answer: (C) Dry friction between surfaces of solids in relative motion or about to move
It obeys the classical laws of dry friction.
Why do vehicle tyres have treads?
Answer: (B) To improve grip by increasing friction and removing water from the contact area
Worn tyres skid more easily on wet roads.
What is the maximum efficiency of a screw jack in terms of friction angle φ?
Answer: (A) (1 − sin φ)/(1 + sin φ)
It occurs when the helix angle is 45° − φ/2.
What is the condition for a body to just slide down a rough inclined plane under its own weight?
Answer: (D) The angle of the plane equals the angle of friction (angle of repose)
Above this angle the body accelerates down the plane.
What is the angle of friction for a coefficient of friction of 1?
Answer: (B) 45°
tan 45° = 1.
What is the main advantage of rolling contact over sliding contact in machines?
Answer: (C) Much lower friction and wear
Ball and roller bearings use rolling contact.
How does the friction force between two dry surfaces vary with the area of contact, for the same load?
Answer: (D) It is practically independent of the area
This is one of the classical laws of friction.