Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Engineering Mechanics: Equilibrium and Trusses

Mechanical Engineering · Engineering Mechanics

30 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What are the conditions of equilibrium for a body acted on by coplanar forces?

  1. The sum of horizontal forces, the sum of vertical forces and the sum of moments must each be zero
  2. Only the sum of moments must be zero
  3. The forces must be equal
  4. Only the sum of forces must be zero
Show answer & solution

Answer: (A) The sum of horizontal forces, the sum of vertical forces and the sum of moments must each be zero

ΣFx = 0, ΣFy = 0 and ΣM = 0.

Question 2

When three non-parallel forces keep a rigid body in equilibrium, what must be true?

  1. They must act in the same direction
  2. They must be coplanar and concurrent
  3. They must be parallel
  4. They must be equal
Show answer & solution

Answer: (B) They must be coplanar and concurrent

Their lines of action must meet at one point.

Question 3

What is a perfect frame?

  1. A frame with more members than needed
  2. A frame with no joints
  3. A frame with fewer members than needed
  4. A frame with just enough members to keep it rigid, where n = 2j − 3
Show answer & solution

Answer: (D) A frame with just enough members to keep it rigid, where n = 2j − 3

n is the number of members and j the number of joints.

Question 4

What is a deficient (imperfect) frame?

  1. A frame with more members than needed
  2. A perfect frame
  3. A frame with fewer members than needed for rigidity (n < 2j − 3)
  4. A frame with no load
Show answer & solution

Answer: (C) A frame with fewer members than needed for rigidity (n < 2j − 3)

It will collapse under load.

Question 5

What is a redundant frame?

  1. A frame with more members than needed for rigidity (n > 2j − 3)
  2. A frame with fewer members
  3. A frame with no supports
  4. A perfect frame
Show answer & solution

Answer: (A) A frame with more members than needed for rigidity (n > 2j − 3)

Its member forces cannot be found by statics alone.

Question 6

What type of forces do members of a pin-jointed truss carry?

  1. Shear only
  2. Axial tension or compression only
  3. Torsion only
  4. Bending only
Show answer & solution

Answer: (B) Axial tension or compression only

Members are two-force members.

Question 7

What are the main assumptions in analysing simple trusses?

  1. Loads act at mid-member
  2. Members bend
  3. Members are welded
  4. Members are pin-jointed, loads act only at joints and members are weightless
Show answer & solution

Answer: (D) Members are pin-jointed, loads act only at joints and members are weightless

These make every member a two-force member.

Question 8

What is the method of joints?

  1. Cutting the truss with a section
  2. Using virtual work only
  3. Analysing a truss by applying equilibrium equations at each joint in turn
  4. Using a graph
Show answer & solution

Answer: (C) Analysing a truss by applying equilibrium equations at each joint in turn

No more than two unknowns can be solved at each joint.

Question 9

In the method of sections, how many members with unknown forces should the section cut?

  1. Not more than three
  2. Only one
  3. All members
  4. Five
Show answer & solution

Answer: (A) Not more than three

Three equations of equilibrium are available for the cut part.

Question 10

What shape does a cable take under a load uniformly distributed per horizontal length?

  1. Circle
  2. Parabola
  3. Straight line
  4. Catenary
Show answer & solution

Answer: (B) Parabola

A suspension bridge cable is nearly parabolic.

Question 11

What shape does a uniform cable hanging under its own weight take?

  1. Ellipse
  2. Parabola
  3. Circle
  4. Catenary
Show answer & solution

Answer: (D) Catenary

For a small sag, the catenary is close to a parabola.

Question 12

What is the principle of virtual work?

  1. Work is always positive
  2. For a body in equilibrium, the total work done by forces during any small virtual displacement is zero
  3. Virtual work is always maximum
  4. Work equals energy lost
Show answer & solution

Answer: (B) For a body in equilibrium, the total work done by forces during any small virtual displacement is zero

Forces that do no work, such as reactions at frictionless supports, are left out.

Question 13

What types of support reaction does a hinged (pinned) support provide?

  1. A force in any direction (two components), but no moment
  2. No reaction
  3. A moment only
  4. Only a vertical force
Show answer & solution

Answer: (A) A force in any direction (two components), but no moment

A fixed support also resists moment.

Question 14

What reaction does a roller support provide?

  1. Forces in any direction
  2. A moment
  3. A force perpendicular to the surface on which it rolls
  4. A horizontal force only
Show answer & solution

Answer: (C) A force perpendicular to the surface on which it rolls

Rollers allow movement along the surface.

Question 15

Why might a heavy ladder resting on the floor and against a wall not stay in equilibrium?

  1. If the ladder is vertical
  2. If the ladder is light
  3. If both are rough
  4. If both the floor and the wall are smooth, there is no friction to resist sliding
Show answer & solution

Answer: (D) If both the floor and the wall are smooth, there is no friction to resist sliding

At least one surface must provide friction.

Question 16

What is the force of friction at the top of a ladder resting against a smooth wall?

  1. Equal to the floor friction
  2. Maximum
  3. Zero
  4. Equal to the weight
Show answer & solution

Answer: (C) Zero

A smooth surface gives only a normal reaction.

Question 17

A beam of span 6 m is simply supported and carries a point load of 12 kN at 2 m from the left support. What is the reaction at the left support?

  1. 4 kN
  2. 6 kN
  3. 8 kN
  4. 12 kN
Show answer & solution

Answer: (C) 8 kN

Taking moments about the right support: R_L × 6 = 12 × 4.

Question 18

A simply supported beam of span 4 m carries a uniformly distributed load of 5 kN/m over its full span. What is each support reaction?

  1. 2.5 kN
  2. 5 kN
  3. 10 kN
  4. 20 kN
Show answer & solution

Answer: (C) 10 kN

Total load 20 kN is shared equally.

Question 19

What is a two-force member?

  1. A member under bending
  2. A member with no forces
  3. A member with two loads at mid-span
  4. A member acted on by forces at only two points, so that the forces are equal, opposite and collinear
Show answer & solution

Answer: (D) A member acted on by forces at only two points, so that the forces are equal, opposite and collinear

Truss members are two-force members.

Question 20

What is a zero-force member in a truss?

  1. A member that carries no force under a particular loading
  2. A member carrying maximum force
  3. A member with no joints
  4. A member under bending
Show answer & solution

Answer: (A) A member that carries no force under a particular loading

Such members may still be needed for stability or other loads.

Question 21

At an unloaded joint where only two non-collinear members meet, what are the forces in those members?

  1. They are maximum
  2. One is zero
  3. Both are equal and non-zero
  4. Both are zero
Show answer & solution

Answer: (D) Both are zero

Equilibrium can only be satisfied if both forces vanish.

Question 22

What is the condition of equilibrium of a particle?

  1. The sum of moments is zero only
  2. The resultant of all forces acting on it is zero
  3. It must be moving
  4. It must have no mass
Show answer & solution

Answer: (B) The resultant of all forces acting on it is zero

For a particle, moments are not considered.

Question 23

What does a fixed (built-in) support provide?

  1. Horizontal and vertical reactions and a resisting moment
  2. No reaction
  3. Only a vertical reaction
  4. Only a horizontal reaction
Show answer & solution

Answer: (A) Horizontal and vertical reactions and a resisting moment

A cantilever is fixed at one end.

Question 24

What is the sag of a cable carrying a uniformly distributed load w per horizontal length over span L with horizontal tension H?

  1. H/wL²
  2. wL/H
  3. wL²/8H
  4. wL²/H
Show answer & solution

Answer: (C) wL²/8H

The cable takes a parabolic shape.

Question 25

How does increasing the sag of a cable affect its horizontal tension for the same load and span?

  1. It increases the tension
  2. It reduces the tension
  3. It has no effect
  4. It makes the tension zero
Show answer & solution

Answer: (B) It reduces the tension

Tight cables carry very large tensions.

Question 26

What are statically determinate structures?

  1. Structures needing extra compatibility equations
  2. Structures with no supports
  3. Structures that move
  4. Structures whose reactions and internal forces can be found from the equations of statics alone
Show answer & solution

Answer: (D) Structures whose reactions and internal forces can be found from the equations of statics alone

Simple trusses and simply supported beams are determinate.

Question 27

What is a truss?

  1. A solid beam
  2. A column
  3. A cable
  4. A structure made of straight members joined at their ends to form triangles
Show answer & solution

Answer: (D) A structure made of straight members joined at their ends to form triangles

Triangles make the structure rigid.

Question 28

Why is the triangle the basic unit of a truss?

  1. It is the cheapest shape
  2. It is the simplest shape that cannot change shape without changing the length of its sides
  3. It has no joints
  4. It is the lightest shape
Show answer & solution

Answer: (B) It is the simplest shape that cannot change shape without changing the length of its sides

A four-sided frame without bracing can collapse.

Question 29

What graphical method is used to find forces in all members of a truss at once?

  1. Maxwell's force diagram (reciprocal diagram)
  2. Mollier diagram
  3. Mohr's circle
  4. Moody chart
Show answer & solution

Answer: (A) Maxwell's force diagram (reciprocal diagram)

It uses Bow's notation for labelling spaces.

Question 30

A body is in equilibrium under three forces of 30 N, 40 N and 50 N. What is the angle between the 30 N and 40 N forces?

  1. 45°
  2. 60°
  3. 90°
  4. 120°
Show answer & solution

Answer: (C) 90°

30, 40 and 50 form a right-angled triangle of forces.

Practice these 30 questions interactively →